Jump to content
SAU Community

Carsales.com.au's Review On The R35 Gtr In Japan.


Recommended Posts

the problem here is weight

as Ferni said, you can't go too far either side of optimal for the damping and have a system that works well

(ie- 'jacking' down or po-go'ing). the engineers have obviously chosen springs that have a huge rate to control the fat body, so that basicaly determines the ride characteristics. the shockies only job is to 'damp' the motion of the springs

also - I hope to god Nissan Australia does ABSOLUTELY NOTHING to suspension settings on account of MOTOR/Wheels magazine and the UK guys whining about comfort

:/

When the 350Z was released, the exact same complaints were made about its ride. So they revised the suspension for the European models, with help from Nissan UK. Guess what happened? Those suspension revisions ended up in later model 350Zs internationally, and everyone concluded the car drove better on the road since it was absorbing bumps. On road loops the Euro-spec setup was quicker and more confidence inspiring, and made the car more enjoyable to drive.

As always, the Japanese can't seem to tune suspension. They always assume "stiffer = better" when its not the case, especially not for a street car driven by ordinary people. A car with progressive handling is always quicker than something super sensitive unless you're a good driver (which most people are not).

Considering the car in question is not the V-Spec or N1, I hope they do something about the suspension if its as bad as they say. If someone complains about a track-focused car being too harsh on the road but great on the track, I'd agree that they're nuts, but if you intend on living the GT-R as a "daily drivable supercar" then I'd rather it absorb bumps and maintain constant tyre contact with the road.

As always, the Japanese can't seem to tune suspension. They always assume "stiffer = better" when its not the case, especially not for a street car driven by ordinary people. A car with progressive handling is always quicker than something super sensitive unless you're a good driver (which most people are not).

I thought the GTR used Bilstein suspension and was tuned by the guys at Bilstein?

Anyway, there is no way the GTR with its weight can lap the Nurg in 7:38 with softer suspension. Nissan engineers knew that and they had to compromise the softer suspension in order to get the lap time they were after.

I think you'll find that the differences between japanese-tuned suspension and australian-tuned suspension has more to do with the roads in each place than the engineers.

I love the term "built for australian roads" - in other words, have the suspension as soft as you can possibly make it so as not to spill your drink every 5m when you hit a pothole or some piece of badly cracked bitumen. Our roads (at least here in SA) are bumpy and extremely crap. On a good quality flat road, my stagea is more comfortable than just about every other car i've been in. It kind of just glides along, no seasickness etc.

But give it your average adelaide road and the suspension is less than perfect :P

As far as the article is concerned. Most of the aussie car reviewers are so brainwashed into aussie cars its no wonder it only scored 3.5/5.0. They were probably just confused because they couldn't work out what model of holden it was...

Correct me if im wrong, but the Aussie guy that test drove the GTR was from MOTOR magazine?

As i can recall, guys at MOTOR magazine have always been biased towards the GTR's - they don't like GTR's. There was one time, they tested the R34 with other cars and complained that it's handling around the track was more annoying than revolutional. Thats because they didn't know that a GTR is meant to be driven hard to bring out the best in it. They were driving it around the track like pussies.

However, WHEELS magazine have always loved GTR's. They were the ones that gave it the nickname 'Godzilla'. Anyway, i remembered an article where they tested an R34 N1 against a Monaro GTS or somethin and they said that the GTR was "the best car they've ever driven - no kidding".

Man these guys dont know how to drive pfft 4.0 wait till people own this car and get familiar with it easy mid 3s and mid to low 11s...

umm, with launch control and DSG what does the driver actually have to do to but hold the right pedal down???

umm, with launch control and DSG what does the driver actually have to do to but hold the right pedal down???

They were testing in slightly damp conditions. Hence there could be a couple of tenths that can be cut from the 0-100kmh time and the 0-400m (also mentioning they hit the 180kmh limiter before they reached the end of the 400m and they still managed a 12.1).

a) GT-R has launch control and b) it works! Using it to good effect on the complex's deserted dragstrip, in the failing light at the end of the Sendai session, MOTOR's David Morley punched out an even 4.0sec for the 0-100km/h sprint and 12.1sec for the standing 400m.

While in 'normal' conditions the 4.0sec will be hard to trim...

nothing about it being damp when they did it. If it was damp I doubt they'd say it would be hard to beat in normal conditions. so my point about knowing how to drive, or getting familiar with the car helping accelleration times significantly still stands.

nothing about it being damp when they did it. If it was damp I doubt they'd say it would be hard to beat in normal conditions. so my point about knowing how to drive, or getting familiar with the car helping accelleration times significantly still stands.

It seems you're right. did they mention what revs the launch control takes off? is it a clutch frying redline launch?

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Yeah, it's getting like that, my daughter is coming over on Thursday to help me remove the bonnet so I can install the Carbuilders underbonnet stuff,  I might get her to give me a hand and remove the hardtop, maybe, because on really hot days the detachable hardtop helps the aircon keep the interior cool, the heat just punches straight through to rag top I also don't have enough hair for the "wind in the hair" experience, so there is that....LOL
    • Could be falling edge/rising edge is set wrong. Are you getting sync errors?
    • On BMWs what I do because I'm more confident that I can't instantly crush the pinch welds and do thousands of USD in chassis damage is use a set of rubber jacking pads designed to protect the chassis/plastic adapter and raise a corner of the car, place the aforementioned 2x12 inch wooden planks under a tire, drop the car, then this normally gives me enough clearance to get to the front central jack point. If you don't need it to be a ramp it only needs to be 1-1.5 feet long. On my R33 I do not trust the pinch welds to tolerate any of this so I drive up on the ramps. Before then when I had to get a new floor jack that no longer cleared the front lip I removed it to get enough clearance to put the jack under it. Once you're on the ramps once you simply never let the car down to the ground. It lives on the ramps or on jack stands.
    • Nah. You need 2x taps for anything that you cannot pass the tap all the way through. And even then, there's a point in response to the above which I will come back to. The 2x taps are 1x tapered for starting, and 1x plug tap for working to the bottom of blind holes. That block's port is effectively a blind hole from the perspective of the tap. The tapered tap/tapered thread response. You don't ever leave a female hole tapered. They are supposed to be parallel, hence the wide section of a tapered tap being parallel, the existince of plug taps, etc. The male is tapered so that it will eventually get too fat for the female thread, and yes, there is some risk if the tapped length of the female hole doesn't offer enough threads, that it will not lock up very nicely. But you can always buzz off the extra length on the male thread, and the tape is very good at adding bulk to the joint.
    • Nice....looking forward to that update
×
×
  • Create New...