Jump to content
SAU Community

Recommended Posts

I've got my original R33 s2 bonnet sitting in my room and would like to remove the small water spray part from the bonnet without breaking/scratching anything.

Reason being - i've now got a carbon bonnet and would like to install them on it.

Any hints/tips would be great (before I apply the brute force approach next weekend).

Thanks for the help.

Mark

I tried pulling out the stock ones.. there is a plastic plate that holds it in there - but you might have to remove the sound/head foam to get to it..

i didn't want to use the brute force approach for fear of scratching (quite likely), and there didn't look like any easy way to get them out without twisting them :P

Did you managed to get them off predator?

I dont recall any plate on/near them, mine just seem to be a clip on the underside of the bonnet. My lack of a decent set of plyers prevented me from taking them off.

Do you think any sort of aftermarket spray will fit? I might just not bother with the old ones...

Mark

  • 2 weeks later...

MRK25T,

if you havent got them off yet, and dont have the plyers then just get a screw driver and push the tab underneath the bonnet to remove. should have to force it much at all, took me 5 seconds to do!!!

currently undergoing a full respray!!

oh well good luck

Mud - I got the carbon bonnet from UAS (www.gtr.com.au) about 2 weeks ago at the open day they had. Nick, Tosh, Carlo, etc. took my old bonnet off and put the new one on while I waited.

Craved - I haven't had a chance to have a nother go at the sprays yet. My bonnet is in my room at my parents place but i'm living with my girlfriend elsewhere.

I'll give it a go with the screw driver Saturday arvo after I finish work at Maccas.

What does it cost to get a full respray in normal metallic?

Mark

MRK25T,

well really depends on what you do your self!!!!

Only costing me $1500 with 2pac paint and pearl + a little air brushing..... but that is a mate doing that......

Most of the price for a full respray comes from actually preparing the car, rubbing back etc....

So when i lost my licence 3 months ago... i did it all my self, nearly finished after 2.5 months of weekend work, would have been quicker but i'm making my own side skirts and pods so that has taken heaps of time.....

3 weeks to go til i see if it was worth it :)

yeah $1500 --- paint and painter

thats all i had to pay for!

helps when you know people in that field, and take the time to do things your self! --(not that i had much driving to do :) )

the spray booth is not yet factored in -- if i cant get one

will have to hire for $400

btw MRK25T

think i saw you working on that bonnet at UAS, was there to pick up parts.. how'd you get the bonnet home?

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • After my last update, I went ahead with cleaning and restoring the entire fuel system. This included removing the tank and cleaning it with the Beyond Balistics solution, power washing it multiple times, drying it thoroughly, rinsing with IPA, drying again with heat gun and compressed air. Also, cleaning out the lines, fuel rail, and replacing the fuel pump with an OEM-style one. During the cleaning process, I replaced several hoses - including the breather hose on the fuel tank, which turned out to be the cause of the earlier fuel leak. This is what the old fuel filter looked like: Fuel tank before cleaning: Dirty Fuel Tank.mp4   Fuel tank after cleaning (some staining remains): Clean Fuel Tank.mp4 Both the OEM 270cc and new DeatschWerks 550cc injectors were cleaned professionally by a shop. Before reassembling everything, I tested the fuel flow by running the pump output into a container at the fuel filter location - flow looked good. I then fitted the new fuel filter and reassembled the rest of the system. Fuel Flow Test.mp4 Test 1 - 550cc injectors Ran the new fuel pump with its supplied diagonal strainer (different from OEM’s flat strainer) and my 550cc injectors using the same resized-injector map I had successfully used before. At first, it idled roughly and stalled when I applied throttle. Checked the spark plugs and found that they were fouled with carbon (likely from the earlier overly rich running when the injectors were clogged). After cleaning the plugs, the car started fine. However, it would only idle for 30–60 seconds before stalling, and while driving it would feel like a “fuel cut” after a few seconds - though it wouldn’t fully stall. Test 2 – Strainer swap Suspecting the diagonal strainer might not be reaching the tank bottom, I swapped it for the original flat strainer and filled the tank with ~45L of fuel. The issue persisted exactly the same. Test 3 – OEM injectors To eliminate tuning variables, I reinstalled the OEM 270cc injectors and reverted to the original map. Cleaned the spark plugs again just in-case. The stalling and “fuel cut” still remained.   At this stage, I suspect an intermittent power or connection fault at the fuel pump hanger, caused during the cleaning process. This has led me to look into getting Frenchy’s fuel hanger and replacing the unit entirely. TL;DR: Cleaned and restored the fuel system (tank, lines, rail, pump). Tested 550cc injectors with the same resized-injector map as before, but the car stalls at idle and experiences what feels like “fuel cut” after a few seconds of driving. Swapped back to OEM injectors with original map to rule out tuning, but the issue persists. Now suspecting an intermittent power or connection fault at the fuel pump hanger, possibly cause by the cleaning process.  
    • For race cars, this is one part where I find having the roll cage bar having gone through a hole in the floor better than the build it up on a ledge inside... The Merc I help on, the main hoop ends are marked on the car, and the jack is marked... Jack goes under a few inches and lifts one whole side of the car up... Removes that fight for long slim jacks for race car duties!   My biggest issue for the daily drivers I work on, is my jacks don't go high enough. The jacks start out on a few blocks, jack it up, then start a second jack under it on more blocks, and then I can get an axle stand under it. My axle stands are presently in use, and are nearly fully extended. The car is sitting with barely more than a cm of clearance to get the wheel off the studs! Sarah's Kluger is the same, as it has an ungodly amount of droop available in the suspension and a distinct lack of good jacking points!
    • Happy? Yep, my to do list is getting shorter and shorter. Either this light approaching is the end of the tunnel, or I'm about to be hit by a train... Ha ha ha   Also, Duncan isn't that far out of town that you need to make a multi day drive out of it. 😛
    • Sorry I meant that we are building the EH for a client.
    • LOL, when one "money pit" is never enough Noice, and excellent work mate
×
×
  • Create New...