Jump to content
SAU Community

Different Boost Readings?

Alex_r33s2gts25t

By Alex_r33s2gts25t,
in Engines & Forced Induction

 Share

Recommended Posts

Alex_r33s2gts25t Enthusiast

Alex_r33s2gts25t

Posted
Posted

Evening fellow car lovers...

My car - R33 GTST

Recently i did the following modifications... upgraded to R34 GTT intercooler, installed Turbo Smart Dual Stage Boost Controller (switch mounted in cabin to switch between a high and low boost setting) and a Drift Boost Guage. Installed everything myself...

Now... with the boost controller at its minimal settings (as low as the dials can go), im getting 2 different boost readings between the factory guage and the aftermarket one. I installed the aftermarket one onto the thicker hose commin off the intake manifold goin to the fuel pressure regulator (so the guages are taking readins of opposite sides of the intake manifold).

Stock guage is telling me about 8-9 psi... aftermarket guage is telling me 0.75 bar... thats like near 11psi??

Why/Which is correct??? :down: lol in oversight whats the point of having a dual stage boost controller if at its low boost setting its already at the limit of the factory turbo :D (i wasnt planin on upgradin the turbo)

Any input would be greatly appreciated :)

Link to comment
https://www.sau.com.au/forums/topic/199271-different-boost-readings/
Share on other sites
blind_elk Grand Master

blind_elk

Posted
Posted

Firstly, a gauge is only as good as the manufacturer. It's not beyond the realms of possibility for 2 different gauges to give 2 different readings of the same thing. The Nissan factory gauges are notoriously inaccurate, though.

And a boost controller cannot lower the boost below standard. It can only raise boost above standard.

260tech Proficient

260tech

Posted
Posted
Firstly, a gauge is only as good as the manufacturer. It's not beyond the realms of possibility for 2 different gauges to give 2 different readings of the same thing. The Nissan factory gauges are notoriously inaccurate, though.

And a boost controller cannot lower the boost below standard. It can only raise boost above standard.

Like the man says, if you are concerned get your aftermarket boost gauge calibrated.

Cheers GW

MBS206 Grand Master

MBS206

Posted
Posted

The aftermarket boost controller, should be able to get boost BELOW 7PSi, if installed correctly.

The factory actuator is only a 3PSi setup.

The question is, did you remove the factory solenoid?

Also, have you removed the ball and spring from the Turbo Smart tee-piece?

Those boost controllers aren't that great... I ran one, switched for the little $20 boost controller and haven't looked back!

swanny180 Proficient

swanny180

Posted
Posted
The aftermarket boost controller, should be able to get boost BELOW 7PSi, if installed correctly.

The factory actuator is only a 3PSi setup.

The question is, did you remove the factory solenoid?

Also, have you removed the ball and spring from the Turbo Smart tee-piece?

Those boost controllers aren't that great... I ran one, switched for the little $20 boost controller and haven't looked back!

Uhhh no Im pretty sure the stock R33 GTST actuator is set at 7psi...

Have you ever actually seen a 33 hold 3psi on a stock turbo with everything functioning correctly?

Alex_r33s2gts25t Enthusiast

Alex_r33s2gts25t

Posted
  • Author
Posted

I did remove the factory boost solenoid... and what spring inside tpeice???? lol i just hooked the tpeice between the turbo nd wastegate like the instructions said and blocked off the other top hose which went to the factory boost solenoid... nd yeah at its minimal settings its at like .75 bar lol

What sort of things would i need to check to see if anythin went wrong in installation?? Im pretty sure i did everything correctly though cause it all works lol

Jdfnq Proficient

Jdfnq

Posted
Posted
Uhhh no Im pretty sure the stock R33 GTST actuator is set at 7psi...

Have you ever actually seen a 33 hold 3psi on a stock turbo with everything functioning correctly?

Yeah the stock actuator is two stage. 5psi to 5000rpm then 7psi to redline :thumbsup:

R34GTFOUR Mentor

R34GTFOUR

Posted
Posted

I take it that your Drift boost gauge just a cheap knock off, in which case its properly as useless as the stock one. Go out and get a proper brand gauge, personally i wouldnt use any thing less than autometer (not autogague) so that means around the 100-150mark depending where you get it from, if you want to spend more on apexi and the like thats all good, you'll probably get an even more accurate reading but in your case an autometer should serve you well.

If you have the basic breathing mods done, ie fmic, turboback exhaust and filter than on low boost with no solinod you should be around the 6-7psi mark.

The location on the manifold where you get your vacuum/boost reading doesnt matter as long as its definately a manifold feed.

260tech Proficient

260tech

Posted
Posted
LOL, where do you go about getting boost guages caliibrated?

Nearly missed this, first off gauge needs to be cabable of being opened without terminal damage being inflicted. (best option) if not can get correction chart? The yellow pages is always a good place to start, mechanical gauge range = press - 0 - vacuum, electrical = take sensor also. Any NATA instro calibration company or connections to airforce/airlines/altimeter calibration joints, know anyone in the sky-diving game.......breathing? :thumbsup:

Cheers GW

Alex_r33s2gts25t Enthusiast

Alex_r33s2gts25t

Posted
  • Author
Posted

Heya, i dont think the drift guage is faulty, it sells for 90 bux... nd is pretty lol...

I havent done air intake or exhaust mods yet... pod filter is on its way from ebay :banana: nd exhuast wont be for a while. Ahwell i dont really need the turbo to boost more than it is at the moment anyway lol, after i get the exhaust and a safc ill get tuned on a dyno and they can look at it then :down:

thanx for input guys

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • S1_C34
      Stagea Front CV Axle Question

      By S1_C34 · Posted

      I ordered a GSP Front R/H Axle from here - https://justjap.com/products/gsp-premium-front-driveshaft-r-h-nissan-r32-r33-r34-skyline-gtr-stagea-4wd#description It lasted around a year before one of the boots blew out. I'm lowered, but I have GKTech roll center adjusters. One year seems a little premature. I think I'm going to spend the extra money on an OEM cv axle this time. This website - https://tfaspeed.com/collections/nissan-stagea-wgnc34-x-four-parts/products/nissan-stagea-awc34-260rs-rb26-right-front-axle-drive-assembly Makes it sound like the readily available OEM CV axle will only fit 11.1999 Stagea and up (mine is a 2.1997 S1). The JustJap listing didn't mention any years or anything for the GSP axle. Amayama shows '11.1999' and up as well for that part number. As well as 'plastic boot type'. See attached picture. So I guess my question is, does that axle (39100-23U60) really only fit S2 Stagea? It's the front driver side. If it does, I'd love to buy that instead of rolling the dice on another GSP. I've found that OEM one cheaper here: https://www.partsfornissans.com/oem-parts/nismo-jdm-r32-r33-r34-skyline-gtr-r32-gts4-right-front-axle-3910023u60 and here https://www.nissanparts.cc/oem-parts/nismo-shaft-ft-drive-3910023u60 Just a little confused because the JapSpeed listing for the GSP front driver axle doesn't mention any specific years or anything and it fit my S1 Stagea fine. So will 39100-23U60 fit my S1 Stagea even though technically it says '11.1999' and up? What would have changed? Thanks.  
    • TurboTapin
      CD009 RB Conversion

      By TurboTapin · Posted

      Thanks for the info. The only "Issue" I've had with the shifter is I always found the throw between 4th and 6th gear too close. I'm always worried to shift into 4th accidently and sending my motor to the moon. Adam LZ recently came out with a video and stated Serialnine revised their shifters to correct this and will change all the revised parts for 150$. Strangely enough, I contacted Serialnine right after and they denied it and said it's bullshit. I found that strange as he's a distributer. I'll keep this forum post updated on that saga.
    • Nightmare_mistress_R33
      CD009 RB Conversion

      By Nightmare_mistress_R33 · Posted

      Yep that is correct. It allows you to adjust the short throw range from what I can tell
    • TurboTapin
      R32 GTST - 600KW+ RB28/CD009 Build

      By TurboTapin · Posted

      Car has been running great, I've put about 300km's of break in time on it. First thing that stands out with properly sealing rings is no more noticeable crankcase smell coming out of my catch can. This may seem insignificant, but the constant smell while driving around was infuriating. It's also nice to see my oil level remain stable. Two new issues have developed that I only noticed this weekend though. There's a very noticeable driveline vibration past 100kmh. I only noticed it now as I've been babying it under 100kmh in the backroads. This comes as no surprise as I'm running a one-piece shaft, and I paid zero attention to my driveshaft angle when I put everything back in. I also have a fair bit of voltage drop on hot starts. The starter audibly is forcing. No issues on cold start though. I must not have removed all the paint under my main block ground during assembly. I'll try and take care of both those issues this week once the kids are asleep.  I also received all the parts I was missing for my direct port setup. I will hopefully have pictures of that up soon. I'm hoping to get back on the dyno the week of June 30th as I'll be on vacation. I'm confident I should be able to make north of 500rwkw on pump gas and WMI. I'll go back again later this summer with E98, but I want to confirm my ethanol content sensor is working properly first. I've never seen it read anything but 11%. This makes sense for our 10% ethanol content pump gas here, but I would expect the occasional movement between fill ups. 
    • jez NF
      The Evolution Of "night Fury"

      By jez NF · Posted

      75% complete. Will now need to get a new axle with 5x114.3 hubs and then figure out how to customize some mudguards for it once the wheels are on.
×
×
  • Create New...