Jump to content
SAU Community

Recommended Posts

Yeah,

I've been watching BMI for a while now and noticed that most of the hardcore time attack monsters and the Super GT cars in Japan has this thing call CANARDS attached to the side of the front bumper.

I could sort of figured out what they are for but the question is do they REALLY work? If they do why our V8 super cars wouldn't have them on?

post-1327-1199061918_thumb.jpg

Link to comment
https://www.sau.com.au/forums/topic/199648-canards/
Share on other sites

*apparently* at highway speeds the front is slightly more stable, but it would depend on the car i guess.

V8 supercars arent exactly the most aerodynamic things to begin with lol.

Edited by s2k12
Link to comment
https://www.sau.com.au/forums/topic/199648-canards/#findComment-3557567
Share on other sites

what are canards designed for? are they for downforce or to direct the airflow around the car more efficiently? if they are for downforce, they would probably work better at high speed (racetrack). also the front bar would have to be more rigid so the downforce didn't just flex it.

my 2 cents.

Link to comment
https://www.sau.com.au/forums/topic/199648-canards/#findComment-3557568
Share on other sites

what are canards designed for? are they for downforce or to direct the airflow around the car more efficiently? if they are for downforce, they would probably work better at high speed (racetrack). also the front bar would have to be more rigid so the downforce didn't just flex it.

my 2 cents.

From Webster Dictionary.

Main Entry: ca·nard

Pronunciation: \kə-ˈnärd also -ˈnär\

Function: noun

Etymology: French, literally, duck; in sense 1, from Middle French vendre des canards à moitié to cheat, literally, to half-sell ducks

Date: 1851

1 a: a false or unfounded report or story; especially : a fabricated report b: a groundless rumor or belief

2: an airplane with horizontal stabilizing and control surfaces in front of supporting surfaces; also : a small airfoil in front of the wing of an aircraft that increases the aircraft's stability

Take your pick. :P

Cheers GW :(

Link to comment
https://www.sau.com.au/forums/topic/199648-canards/#findComment-3557611
Share on other sites

The V8 supercars don't have them because the rules limit the amount of changes they can make from the factory profile of the car (I know, I know, don't shoot the messenger)

What they do have to compensate though, is a very extended lip on the lower leading edge of the front bar that is "supposed" to do the same thing (ie - increase stability on the front end) How much value is in this, when you consider that they don't run the massive tyres and obese amounts of front camber that the BMI and WTCC run, is anyones guess.

Link to comment
https://www.sau.com.au/forums/topic/199648-canards/#findComment-3557778
Share on other sites

supertaxis run 19x11s (or 12s, cant remember) all round... cant really say thats not large...

Ah, no......

They are only allowed to run a 17" rim maximum, with a 305 (10") control tyre.

Not a huge amount of rubber to put 650-700 horses to the ground through 2 tyres....

v8 supercars tech rules (for the non believers)

http://www.v8supercar.com.au/content/attac...ction_c_update/

Link to comment
https://www.sau.com.au/forums/topic/199648-canards/#findComment-3558008
Share on other sites

west

Yeah,

I was bored, watching BMI then i was just wondering if CANARDS really do works? Well all the super GT cars in Japan has them, so are some of the time attack monster overthere ..................so it has to work, even a bit right?

What if V8 supercars has them on? Why wouldn't they?

not trying to be a bastard but is english your first language? sorry for asking . . :blink:

Link to comment
https://www.sau.com.au/forums/topic/199648-canards/#findComment-3558194
Share on other sites

canards used to be fitted to v8 supercars in the early '90s... people might remember them on the seton and johnson falcons. the level of contact in that category might have seen them moved away from if the rules didn't.

they can work if designed and set up to work, i doubt most fitted to road cars have any measurable effect... all most would be good for is extra drag.

Link to comment
https://www.sau.com.au/forums/topic/199648-canards/#findComment-3558214
Share on other sites

From Webster Dictionary.

Main Entry: ca·nard

Pronunciation: \kə-ˈnärd also -ˈnär\

Function: noun

Etymology: French, literally, duck; in sense 1, from Middle French vendre des canards à moitié to cheat, literally, to half-sell ducks

Date: 1851

1 a: a false or unfounded report or story; especially : a fabricated report b: a groundless rumor or belief

2: an airplane with horizontal stabilizing and control surfaces in front of supporting surfaces; also : a small airfoil in front of the wing of an aircraft that increases the aircraft's stability

Take your pick. :D

Cheers GW :(

ha I'll stick with the duck one.

Link to comment
https://www.sau.com.au/forums/topic/199648-canards/#findComment-3558489
Share on other sites

Its for looks. I doubt you would notice it. High speeds?? 911 Turbo, Veyron, F1 Mclaren...I don't see canards on those.

Diffusers at the rear and flat underbody on the hand will do something for aerodynamics.

Canards are just one of those things that one workshop did (I think it was MCR?) and now everyone has to have it.

Back in the 70's people used to raise the bonnet up at the back maybe a couple of cms because someone thought it would be a good idea for heat extraction. It actually did the opposite because of the low pressure zone around the windscreen sucked air into the engine bay and kept the engine nicely insulated with its own heat. They finally realised and changed the design slightly e.g A9X Torana, rear facing sealed hood scoop = oldschool CAI.

/end rant

Link to comment
https://www.sau.com.au/forums/topic/199648-canards/#findComment-3558708
Share on other sites

ok so whats the diffrence with the ones on the time atack cars (canardon the frontbumber 1/2 way up)

and the one on JET 200 (off ignition dvd) that has them parallel with the front bumber on the bottom

no doubt both cars spent plenty of time in the wind tunnel testing alternative designs

Link to comment
https://www.sau.com.au/forums/topic/199648-canards/#findComment-3558856
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Latest Posts

    • CTIS (Central Tire Inflation System) has existed since the 80's. I'm looking into buying a Hummer H1 and they generally included it. 
    • My idle is set at 950rpm though - Moving the timing around 20 degrees is not really what I'd call a calm idle. That said... neither is chop, by definition. The LS ECU likes to adjust timing to hold idle as opposed to air. It'd work, but generally speaking there'd be a discrepancy in the base idle and the IACV would want to move the timing around anyway to maintain said idle. I think I'm just going to keep the timing steady anyway. Preserve my engine mounts.  My aircon is now officially regassed. As the guy was reversing I noticed my reverse lights do not operate, along with my reverse cam. This is a bit distressing, because 100% of guides talk about which wire to connect to backup cams as "the goes with the [other color] wire". Often when doing conversions. Unfortunately the R34 colour wires aren't documented Unfortunately I had a T56 Magnum gearbox with it's reverse switch, which also isn't documented. Unfortunately there's definitely not documentation for people with both of these in the one car. Unfortunately I forgot. After many hours of this, I have a reverse cam and reverse lights again. The wire going through the trans tunnel to the reverse switch had broken. Upon inspection, it looks like this one wire had about 7 spade terminals and extensions in it.. for reasons I cannot possibly comprehend. I also spent the 750 hours required to clean up the wiring behind my head unit which now looks like this: This is a monumental improvement relative to what used to be there WRT triple gauges, head unit, traction control, wideband controller, and whatever the f**k OEM stuff still exists there in various states of connectivity/needed. Next step is to check in at the Exhaust shop to see/confirm how much clearance I have, to decide what mid mufflers or 'resonators' (which are just straight through, narrower mufflers) I can add and hopefully cut out a lot of exhaust leaks, pinhole, v-band or otherwise. But first step will be to 'take a look' before the next step.
    • Fark the AFM card and Nistune, Haltech Nexus S3, DBW, cruise control, flex fuel, dis dat.  
    • It's most likely the bolt/bush where the cover bolts back wore and allowed cover to move forward.
    • Still haven't put the injectors and R35 AFM in so we can tune the bloody thing for the HG highflow it got mid last year! I think I can forecast the upgrade path to a bigger twin scroll, external gate, Haltech, flex setup, Samsonas, dis dat, etc will be .... a while away!
×
×
  • Create New...