Jump to content
SAU Community

Recommended Posts

hey guys

now that we have hot days as soon as its 35+ outside with or without the a/c on my car overheats this only happens when im driving but when i stop the temp starts to drop but takes awile and my overflow bottle was boiling with coolant and over filling? would it be the radiator cap? not holding pressure because it was making air noises when i popped the bonnet up

thanks ppl

Edited by Jsikalias
Link to comment
https://www.sau.com.au/forums/topic/199766-overheating-problem-need-help-pls/
Share on other sites

  • Replies 40
  • Created
  • Last Reply

Top Posters In This Topic

im gonna go with radiator cap not holding pressure.

run the car up to temp, and with the cap on, squeeze the top rad hose, there should be pressure in the hose during normal operation. If there is not then the cap is not sealing, so the coolant will boil. (the pressure raises the boiling point of the water/coolant)

I had the same problem a couple of weeks ago, turns out one of the big fittings on my intake manifold has rusted pretty bad due to a previous owners not using antifreeze, which in turn blocked the radiator and would cause the car to overheat, i would suggest taking out your radiator and get it tested and cleaned.

http://www.skylinesaustralia.com/forums/Co...-O-t196137.html

i dont think it is your pump man. the pump is basically fins on a shaft that push water around. the only thing that goes in the pump is seals and bearings and i doubt that the seals could leak enough coolant to cause that!
If previous owners haven't used coolant treatment (and the Japs are notorious for not doing so), the fins rot away. Under load, the rotted fins cannot circulate the coolant; the engine produces more heat that cannot be removed because the coolant isn't being circulated. At idle, the remaining bits of fin can circulated the water, so it tends to cool a bit.

ive actually got the exact same prob at the moment water pump is less than 5000ks old changed it when i dit the timing belt ect ect . my car has never overheated at all or even come close in the time ive owned it i run good coolent .

the other day 40+ in adelaide going up the hills first thing the aircon cut out ive since found if ya car is getting to hot the ecu cuts the air con r33.

temp gauge went to 3/4 and i pulled over water was pissing out the overflow tank onto the ground we let it cool down and started the car and topped up the water turned around and headed home as it was now going down the hills and hardly any load the needle went back to half and the air con was ok again .

next day thought i would take it thru the hills closer to home and the same thing happened again normal driving even in the hot weather with the air con on its fine its only when ya hit the hills i have trouble.

will put in a new themrostat this week and a new cap and see how that goes .

the rad looks very clean as far as you can see but will get it cleaned out if the thermostat and cap dont help .

let me know what fixers yours if ya find the prob

cheers dean

to flush the radiator u dont neeed to remove it. just d/c the top hose and then the bottom hose. put a hose in the top and flush away. after that flush the engine by sticking the hose into the intake (top hose) and allowiing the watr to come out the bottom.

if u get brown water and crap coming out, thats the issue for ocer heating. rusted dfins and crap in the radiator (rust) that i causing yor issues. but also after doing this getyour cooling system pressure tested.

in my old 33, sme thing happened. flushed radiator, had it checked and still same thing. pressure tested the system found a small leak from a hose that was 10cm long but enough that it was leaking fluid at temp and causing the overheat

yeah dude i had same prob in my 32 when the new motor went in they didnt flush the old rad and engine, the radiator just acted as a huge collection for crap out of the engine it was so blocked ,cleaned with kero and tried as hard as i could to over heat it and it wouldnt

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • ok so if i wanted to go 18's i would go for 8's  in front 30+ or 32+ off set at front and the back 9 would be ok? what offset should i aim for.. then can i do some  hunting for wheel rim choices..   
    • Absolute f*cking nightmare. I had to take breaks constantly, and I was always pissed off when I got home. The line split in Italy on day 2 (we drove from the Netherlands), lol. Driving any narrow European town was... well, sh*t.   Appreciate it man. Here, I'll just drop a favourite from the load I took on Saturday.   I'll update here when things happen with the car, the thing is, with stock power and almost everything chassis-wise taken care of, there really are no problems. 268,000kms now and counting.  
    • Ah! I actually managed to snag a lightly used set.... that aren't so suitable for me right now. They don't work on a GTT without some cutting or creative heat moulding. I thought about reselling them myself cause I didn't want to murder them, but it looks like I'm probably going to attempt to murder them/melt them because I may as well. @GTSBoy @PranK can somebody close this thread?
    • Hey mate,  I have a set, one is slightly damaged but wont be noticable once installed.  Shoot me a message if your still after them 
    • I couldn't wait But, the black constant tension hose clamps were too thick and there wasn't enough clearance at the T/B and I couldn't get it to seat properly, so I had use a silver one there I also added some 3" silicone over the alloy bit that goes through to hole on the radiator support as it looked like it was sitting on the edge of the hole in the radiator support, I never noticed a rattle or anything, but there was a witness mark It is basicly done, and I can live with the silver hose clamp at the T/B, I will get a black clamp for the head vent though where it is attached to the bulkhead fitting  It never stops...LOL, only issue now with the shock tower brace is it slightly touches the under bonnet liner now, if I leave it it will either wear some paint off the brace where it touches, or damage the liner, so I removed the liner to see what I have to work with, with the liner removed I have about 20mm of clearance, but sadly the middle part of the underside of the bonnet is only dusted with paint and looks crap, so I cannot have that, but.... as I have a roll of Carbuilders premium under bonnet insulation in the garage laying around that is only 5.5mm thick (we were going to use it on the boys Patrol, but he crashed the front of it a few months and it was written off, hence why he now drives my old Honda Accord Euro), I'll use the OEM liner as a template and get the Carbuilders stuff fitted up to cover that dusted paint up
×
×
  • Create New...