Jump to content
SAU Community

Recommended Posts

hey guys, whats the story with these?

http://www.d2racingsports.com.au/d2suspension.html

any good?

have also been looking @ the g4s from justjap.

dunno if i can afford 2k suspension.

Edited by eddieeeee-ro
Link to comment
https://www.sau.com.au/forums/topic/200049-d2-adjustable-suspension/
Share on other sites

Steer clear, they are crap IMO.

Currently have them on, came with the car, and will be gone in feb when i get paid.

Way to stiff, the adjustment is a wank and even on the softest setting is far harder then i would want on the street.

As an example of how hard it is, i have a sub box in the boot that has been known to hit the boot lid over some bumps.

Spend your money elsewhere...

i had d2 in my car for about 2-3years (ecr33), in my opinion they are an ok cheap coilover, yes they are hard and bumpy but they use a large spring rate, so its to be expected.

Although the adjustment isn't that great, it still works ok for the price you pay.

while i had the d2 suspension in my car i used it for track (mc, drift, drag) and found the car to handle pretty ok >_<

also when you buy the d2 you can ask for whatever spring rate you like, so you can run something like 4/6 or similar and it wont be as bumpy or hard.

just my 2cents

(also when i bought my d2 they were the only coilovers available in that price range which had both damper and height adjustment)

Having personal experience using these on the track I can confirm they are a good entry level coilover, but my experience has only been with far softer spring rates than the default provided... my only concern would be to longevity with hard use.

The above said, if you have a 2k budget I'd consider Australian spec Tein Super Street from Fulcrum or if you don't require adjustability consider SK's kit.

If you were to go with the D2/G4/K-Sport option, I'd go with Just Jap's G4 brand as their support is excellent.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • How do you propose I cable tie this: To something securely? Is it really just a case of finding a couple of holes and ziptying it there so it never goes flying or starts dangling around, more or less? Then run a 1/8 BSP Female to [hose adapter of choice?/AN?] and then the opposing fitting at the bush-into-oil-block end? being the hose-into-realistically likely a 1/8 BSPT male) Is this going to provide any real benefit over using a stainless/steel 1/4 to 1/8 BSPT reducing bush? I am making the assumption the OEM sender is BSPT not BSPP/BSP
    • I fashioned a ramp out of a couple of pieces of 140x35 lumber, to get the bumper up slightly, and then one of these is what I use
    • I wouldn't worry about dissimilar metal corrosion, should you just buy/make a steel replacement. There will be thread tape and sealant compound between the metals. The few little spots where they touch each other will be deep inside the joint, unable to get wet. And the alloy block is much much larger than a small steel fitting, so there is plenty of "sacrificial" capacity there. Any bush you put in there will be dissimilar anyway. Either steel or brass. Maybe stainless. All of them are different to the other parts in the chain. But what I said above still applies.
    • You are all good then, I didn't realise the port was in a part you can (have!) remove. Just pull the broken part out, clean it and the threads should be fine. Yes, the whole point about remote mounting is it takes almost all of the vibration out via the flexible hose. You just need a convenient chassis point and a cable tie or 3.
    • ..this is the current state of that port. I appreciate the info help (and the link to the Earls thing @Duncan). Though going by that it seems like 1/4 then BSP'ing it and using a bush may work. I don't know where I'd be remote mounting the pressure sender... to... exactly. I assume the idea here is that any vibration is taken up by the semiflexible/flexible hose itself instead of it leveraging against the block directly. I want to believe a stronger, steel bush/adapter would work, but I don't know if that is engineeringly sound or just wishful thinking given the stupendous implications of a leak/failure in this spot. What are the real world risks of dissimilar metals here? It's a 6061 Aluminum block, and I'm talking brass or steel or SS adapters/things.
×
×
  • Create New...