Jump to content
SAU Community

Recommended Posts

I hit up my workout B last night (bi's forearms calves hami's squats) and didn't feel it like I did with the workout a/how I usually would if I was to train legs or arms.. I don't know if this is because I usually overtrain these parts or if I didn't train them enough last night. I felt a bit of a burn while training them but that faded as I went to the next exercise. The routine was

Biceps; 3x10 RPx10,9,9

Forearms; 3x10 RPx10,8,7

Attempt at extreme bi stretch

Calves - attempted this on the 45 degree leg press and seated calve raise with a 10-12 sec negative and didn't get much of a burn

Hami's - 2x10 RPx8,6,5

Squats - 3x8

Any suggestions on what I could've done wrong?/what I should do different

I'd suggest putting the whole DC training thing on pause until you've trained on a 3 day a week beginner program and built some more strength up first. That looks like a fairly meh workout to me; lots of little assistance things with squats at the end, while you're a beginner you might as well take advantage of the fact that you recover quicker than a more experienced trainee.

Edited by bozodos

Terrible workout

Hamstring curl before squats? lulz thread is in the wasteland.

Beginners gotta stop adopting programs of people who have surpassed the need for a beginner style program.

Ditch the isolation shit and hit the compounds hard a few days a week. Eat a truckload of food, get a good sleep and use your rest days for rest. Watch yourself get bigger and stronger than ever with the least time you've ever spent in the gym.

Also, doms and "burn" aren't the best indicators of a good workout; you can get both these from doing 300 reps of 3kg bicep curls.

  • Like 1

I've gotta say, I was a bit paranoid about having to cut back on gym time (too busy these days) so I get around 40-45mins instead of 60-70, but I've mixed up the workload more, dropped rest between sets, using almost exclusively compound exercises and my weight and strength are both still solid for me.

Quite happy with that TBH.

Edited by ActionDan

Biceps; 3x10 RPx10,9,9

Forearms; 3x10 RPx10,8,7

Attempt at extreme bi stretch

Calves - attempted this on the 45 degree leg press and seated calve raise with a 10-12 sec negative and didn't get much of a burn

Hami's - 2x10 RPx8,6,5

Squats - 3x8

Any suggestions on what I could've done wrong?/what I should do different

That's a rubbish routine

You're a beginner, you should be concentrating on compound movements.

DC training appears to be a bodybuilding program.

Not a strength program.

So with that in mind, its focus is asthetic goals.

If its more fun than arnies or ronnies program for you then just do it. Like everything else if you want the results of the guy who thought of it then you are out of luck. without the same genes and the juice program And more importantly the actual effort capabillity .People focus too much on the pro program as a means to the same results. there is night and day in what a punter considers a max lift effort or lift to 'failure' vs a good or professional athlete.

Yes, it is largely for those looking to add mass. But, I'm terribly sorry - if you went from doing 50kg squat for 6, to doing 100kg squat for 6, you just got stronger.

Wanting the results of the guy that created is a moot point, since no one has stated that's their goal. This is not a "pro" program as such; I don't see it being flogged around. Sure, a few pro's use it, but that's because they approached Dante. A lot of the great results have been with guys that don't use any kind of drug enhancement. Sure, they aren't going from 70kg to 110kg monsters in 2 years, but they're getting good results.

Agreed, it takes a certain psychological strength to push past mental blocks when training.. usually only those athletes who are 'good' as you say, or professional, have this ability.

I hit up my workout B last night (bi's forearms calves hami's squats) and didn't feel it like I did with the workout a/how I usually would if I was to train legs or arms.. I don't know if this is because I usually overtrain these parts or if I didn't train them enough last night. I felt a bit of a burn while training them but that faded as I went to the next exercise. The routine was

Biceps; 3x10 RPx10,9,9

Forearms; 3x10 RPx10,8,7

Attempt at extreme bi stretch

Calves - attempted this on the 45 degree leg press and seated calve raise with a 10-12 sec negative and didn't get much of a burn

Hami's - 2x10 RPx8,6,5

Squats - 3x8

Any suggestions on what I could've done wrong?/what I should do different

Good effort, but not quite there..

Your bicep exercise. Unless you're a genetic freak, something isn't right about your weights used, or the effort you put in, or the rest-pausing. RP of 10, 9, 9 ... If you do a proper rest pause, your sets would look something like this - 10, 6, 2. Or something to that effect. I'd say your first set you didn't go to true failure, and if you did, you took too long between sets.

Forearms are just straight sets. You've got to remember your forearms get a lot of indirect work with other exercises.

Legs have to be dead straight, and you have to be honest with how far you let the bottom stretch portion go. The negative is the easy part, holding it completely stretched for 10 seconds is not so easy. The weight should be such that by the 10th rep, your legs are shaking.

Looks like your hamstring exercise was done a bit better. Maybe throw in one more warm up set.

Squats... way off, sorry dude. You should be working your way up in weight, doing sets of 6, until you get to a weight that 6 reps becomes a life or death situation. Then, take only enough rest to get your breath back (usually 90 seconds for me), reduce the weight a little bit, and go for 20 reps. The weight you choose to try and get 20 reps, is a weight that you can normally only get for 10. If you still feel like you "didn't train enough" after doing this properly, I'll buy you a beer.

And like others have said, experiencing "burn" or DOMS is not an indicator of muscle growth. If anything, it's the indication of the opposite.

I'd suggest putting the whole DC training thing on pause until you've trained on a 3 day a week beginner program and built some more strength up first. That looks like a fairly meh workout to me; lots of little assistance things with squats at the end, while you're a beginner you might as well take advantage of the fact that you recover quicker than a more experienced trainee.

"assistance things" ... you seem to think this is a power lifting routine.

However.. I might have to agree with the rest of your points.

Terrible workout

Hamstring curl before squats? lulz thread is in the wasteland.

Beginners gotta stop adopting programs of people who have surpassed the need for a beginner style program.

Ditch the isolation shit and hit the compounds hard a few days a week. Eat a truckload of food, get a good sleep and use your rest days for rest. Watch yourself get bigger and stronger than ever with the least time you've ever spent in the gym.

Also, doms and "burn" aren't the best indicators of a good workout; you can get both these from doing 300 reps of 3kg bicep curls.

It's a good routine; he just did it sub-par. 5/3/1 is a good routine; I'm sure I can find some training logs somewhere that make it a "terrible workout".

So, you have this thing about doing anything before squats/deads, but you haven't really given great reasoning as to why yet? Aside from the possible hindrance bicep curls could have to deadlifting, seeing as though they are under tension.

There is no reason why he can't do some 'isolation' work alongside the compounds; besides, this program calls for doing a heavy compound movement 3 - 4 times a week (if trained on a EOD rotation). Agree with the rest though - eat, sleep, rest (even though walking is active recovery and has been shown to decrease recovery times), and that results can be achieved in less time than most think.

That's a rubbish routine

You're a beginner, you should be concentrating on compound movements.

You guys have this fondness of bagging routines, but you're not giving sound theories as to why they're rubbish?

hazjaz;

This is my log from training on Monday: (all warm ups are 10 rep sets unless otherwise stated - RP=rest pause, SS=straight set)

EZ-Bar Preacher Curl - 10kg, 15kg, 20kg, 25kg, RP-35kg, 23,10,8. (Reps are way too high, need to increase weight a whole lot)

EZ-Bar Reverse preacher curl - 10kg, 15kg, SS-35kg, 10.

Leg press calf raise - 60kg, 80kg, 100kg, SS-130kg, 12. 10 second negative, 8 second hold in stretch position, 2 second hold at top.

Lying leg curl - 32kg, 46kg, 67kg, RP-77kg, 10,5,4.

Squat (warm ups done for 6 reps) - BAR, BAR, BAR, 40kg, 60kg, 80kg, 100kg, SS-145kg, 6 reps. Reduce weight to 117.5kg, 21 reps. (New PB)

Both sets of curls were done in such a way, that you would think my head was about to explode.

The calf raises, by the end of it.. f**k me. My legs were shaking, and I couldn't walk properly.

The leg curls, same thing. I felt nauseous afterwards. My hamstrings were so pumped, that doing the stretches for them, felt like pure agony.

Those squats drilled me. That 21 rep set was a mission to complete. By rep 15, my mind had already started to give up. By rep 17, I nearly gave up. By rep 20, it felt like my lungs were on fire. After racking the bar, I quite literally dropped to the ground.

This is the kind of intensity you need to bring to the program, otherwise you won't see results.

If you're finding it hard to get around the routine, then it might be an idea to do what some of the other guys are recommending. DC training is good, it gives you great results, but it takes a certain amount of focus, intensity and consistency.

I'd be pissing off the preacher curls - not good for your arms. Do standing ones (I prefer straight bar but not everyone has the wrist flexibility). Basically there is too many exercises with too much volume, and compounds should be done first, and heaviest, not at the end of a workout. I personally hate calf raises - you can do them til the cows come home, and I can bet you your legs won't grow appreciably at all. 20 rep squats at light weight are a good way to ensure that you're not going to be putting more weight on the bar effectively either.

That is in regards to Hazjaz btw.

The reason we keep going on about it is because Hazjaz is obviously a beginner in terms of results and type of programming; trying to adapt advanced / intermediate routines for beginners and majoring in the minor shit is a fail, I know this from personal experience.

Generally leg machines are used as the assistance lifts to the big one - the squat. If you want to specialise in just growing muscles that's fine, but it's not the best method to take when starting out, and it's not as efficient as building up a decent amount of strength first.

Edited by bozodos

I'd be pissing off the preacher curls - not good for your arms. Do standing ones (I prefer straight bar but not everyone has the wrist flexibility). Basically there is too many exercises with too much volume, and compounds should be done first, and heaviest, not at the end of a workout. I personally hate calf raises - you can do them til the cows come home, and I can bet you your legs won't grow appreciably at all. 20 rep squats at light weight are a good way to ensure that you're not going to be putting more weight on the bar effectively either.

That is in regards to Hazjaz btw.

The reason we keep going on about it is because Hazjaz is obviously a beginner in terms of results and type of programming; trying to adapt advanced / intermediate routines for beginners and majoring in the minor shit is a fail, I know this from personal experience.

Generally leg machines are used as the assistance lifts to the big one - the squat. If you want to specialise in just growing muscles that's fine, but it's not the best method to take when starting out, and it's not as efficient as building up a decent amount of strength first.

Agreed, preacher curls aren't for everyone. I also like standing barbell curls.. using a bit of body English for the last rep or two means you can use a weight slightly higher than normal; note the keyword being 'bit'.. Too many guys turn it into some kind of bastardised power clean. I guess we're agreeing to disagree about what exercises should come first. Agree with the calf raises part, we established the results will largely come down to genetics. Who said anything about "light weight"? I thought I made it pretty clear that this was a decently heavy weight..

I know that was in regards to Hazjaz, but just wanted to comment anyway :)

It's not impossible to adapt a more advanced routine for someone with less experience.. I've done it with 2 guys who have had no prior weight lifting experience, and they are getting great results. Although, I concede, this could be due to the fact of face-to-face interaction and support.

I still don't see how it is such a big issue to have a supplemental exercise being trained alongside the squat. Programming the squat in this fashion (keeping heavy sets in the 4 - 6 rep range) is perfect for strength gains, with enough TUT to allow for adequate hypertrophy. The heavy 20-rep set performed only further facilitates this. Besides, it's almost legend how effective heavy weight, high rep set squats are for leg development.

Agree strength is a big player in all things, though.

Id like to qualify that by a strength program I meant something that is not "incidental" and relative as it is in the DC program.no intent to disrespect the program.

A 100kg squat is stronger than 50kg but, this program is unlikely to efficiently deliver rapid strength gains on anyone other than a beginner or a complete slacker. And as agreed it is because its an asthetic program. Strength gains are a bonus and necessary incidental benifit but , volume appears to be the main effective vehicle of hypertrophy in the program.

If that makes sense.

EPIC posts, and just to stir the pot a bit more, I claim that under grasp heaves/chins/pull ups are the best exercise for the bicep.

Ive attached my latest if anyone CBF looking, its a slightly modified 8 6 3 from blackironbeast web site, start week 2 on Monday.

I just print it off and tick next to it if I get it and record reps for my + set.

_EXCEL_PROGRAM_4_DAY_4_WEEK (1).xls

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Latest Posts

    • Any update on this one? did you manage to get it fixed?    i'm having the same issue with my r34 and i believe its to do with the smart entry (keyless) control module but cant be sure without forking out to get a replacement  
    • So this being my first contribution to the SAU forums, I'd like to present and show how I had to solve probably one of the most annoying fixes on any car I've owned: replacing a speedometer (or "speedo") sensor on my newly acquired Series 1 Stagea 260RS Autech Version. I'm simply documenting how I went about to fix this issue, and as I understand it is relatively rare to happen to this generation of cars, it is a gigantic PITA so I hope this helps serve as reference to anyone else who may encounter this issue. NOTE: Although I say this is meant for the 260RS, because the gearbox/drivetrain is shared with the R33 GTR with the 5-speed manual, the application should be exactly the same. Background So after driving my new-to-me Stagea for about 1500km, one night while driving home the speedometer and odometer suddenly stopped working. No clunking noise, no indication something was broken, the speedometer would just stop reading anything and the odometer stopped going up. This is a huge worry for me, because my car is relatively low mileage (only 45k km when purchased) so although I plan to own the car for a long time, a mismatched odometer reading would be hugely detrimental to resale should the day come to sell the car. Thankfully this only occurred a mile or two from home so it wasn't extremely significant. Also, the OCD part of me would be extremely irked if the numbers that showed on my dash doesn't match the actual ageing of the car. Diagnosing I had been in communication with the well renown GTR shop in the USA, U.P.garage up near University Point in Washington state. After some back and forth they said it could be one of two things: 1) The speedometer sensor that goes into the transfer case is broken 2) The actual cluster has a component that went kaput. They said this is common in older Nissan gauge clusters and that would indicate a rebuild is necessary. As I tried to figure out if it was problem #1, I resolved problem #2 by sending my cluster over to Relentless Motorsports in Dallas, TX, whom is local to me and does cluster and ECU rebuilds. He is a one man operation who meticulously replaces every chip, resistor, capacitor, and electronic component on the PCB's on a wide variety of classic and modern cars. His specialty is Lexus and Toyota, but he came highly recommended by Erik of U.P.garage since he does the rebuilds for them on GTR clusters.  For those that don't know, on R32 and R33 GTR gearboxes, the speedometer sensor is mounted in the transfer case and is purely an analog mini "generator" (opposite of an alternator essentially). Based on the speed the sensor spins it generates an AC sine wave voltage up to 5V, and sends that via two wires up to the cluster which then interprets it via the speedometer dial. The signal does NOT go to the ECU first, the wiring goes to the cluster first then the ECU after (or so I'm told).  Problems/Roadblocks I first removed the part from the car on the underside of the transfer case (drain your transfer case fluid/ATF first, guess who found out that the hard way?), and noted the transfer case fluid was EXTREMELY black, most likely never changed on my car. When attempting to turn the gears it felt extremely gritty, as if something was binding the shaft from rotating properly. I got absolutely no voltage reading out of the sensor no matter how fast I turned the shaft. After having to reflow the solder on my AFM sensors based on another SAU guide here, I attempted to disassemble the silicone seal on the back of the sensor to see what happened inside the sensor; turns out, it basically disintegrated itself. Wonderful. Not only had the electrical components destroyed themselves, the magnetic portion on what I thought was on the shaft also chipped and was broken. Solution So solution: find a spare part right? Wrong. Nissan has long discontinued the proper sensor part number 32702-21U19, and it is no longer obtainable either through Nissan NSA or Nissan Japan. I was SOL without proper speed or mileage readings unless I figured out a way to replace this sensor. After tons of Googling and searching on SAU, I found that there IS however a sensor that looks almost exactly like the R33/260RS one: a sensor meant for the R33/R34 GTT and GTS-T with the 5 speed manual. The part number was 25010-21U00, and the body, plug, and shaft all looked exactly the same. The gear was different at the end, but knowing the sensor's gear is held on with a circlip, I figured I could just order the part and swap the gears. Cue me ordering a new part from JustJap down in Kirrawee, NSW, then waiting almost 3 weeks for shipping and customs clearing. The part finally arrives and what did I find? The freaking shaft lengths don't match. $&%* I discussed with Erik how to proceed, and figuring that I basically destroyed the sensor trying to get the shaft out of the damaged sensor from my car. we deemed it too dangerous to try and attempt to swap shafts to the correct length. I had to find a local CNC machinist to help me cut and notch down the shaft. After tons of frantic calling on a Friday afternoon, I managed to get hold of someone and he said he'd be able to do it over half a week. I sent him photos and had him take measurements to match not only the correct length and notch fitment, but also a groove to machine out to hold the retentive circlip. And the end result? *chef's kiss* Perfect. Since I didn't have pliers with me when I picked up the items, I tested the old gear and circlip on. Perfect fit. After that it was simply swapping out the plug bracket to the new sensor, mount it on the transfer case, refill with ATF/Nissan Matic Fluid D, then test out function. Thankfully with the rebuilt cluster and the new sensor, both the speedometer and odometer and now working properly!   And there you have it. About 5-6 weeks of headaches wrapped up in a 15 minute photo essay. As I was told it is rare for sensors of this generation to die so dramatically, but you never know what could go wrong with a 25+ year old car. I HOPE that no one else has to go through this problem like I did, so with my take on a solution I hope it helps others who may encounter this issue in the future. For the TL;DR: 1) Sensor breaks. 2) Find a replacement GTT/GTS-T sensor. 3) Find a CNC machinist to have you cut it down to proper specs. 4) Reinstall then pray to the JDM gods.   Hope this guide/story helps anyone else encountering this problem!
    • So this being my first contribution to the SAU forums, I'd like to present and show how I had to solve probably one of the most annoying fixes on any car I've owned: replacing a speedometer (or "speedo") sensor on my newly acquired Series 1 Stagea 260RS Autech Version. I'm simply documenting how I went about to fix this issue, and as I understand it is relatively rare to happen to this generation of cars, it is a gigantic PITA so I hope this helps serve as reference to anyone else who may encounter this issue. NOTE: Although I say this is meant for the 260RS, because the gearbox/drivetrain is shared with the R33 GTR with the 5-speed manual, the application should be exactly the same. Background So after driving my new-to-me Stagea for about 1500km, one night while driving home the speedometer and odometer suddenly stopped working. No clunking noise, no indication something was broken, the speedometer would just stop reading anything and the odometer stopped going up. This is a huge worry for me, because my car is relatively low mileage (only 45k km when purchased) so although I plan to own the car for a long time, a mismatched odometer reading would be hugely detrimental to resale should the day come to sell the car. Thankfully this only occurred a mile or two from home so it wasn't extremely significant. Also, the OCD part of me would be extremely irked if the numbers that showed on my dash doesn't match the actual ageing of the car. Diagnosing I had been in communication with the well renown GTR shop in the USA, U.P.garage up near University Point in Washington state. After some back and forth they said it could be one of two things: 1) The speedometer sensor that goes into the transfer case is broken 2) The actual cluster has a component that went kaput. They said this is common in older Nissan gauge clusters and that would indicate a rebuild is necessary. As I tried to figure out if it was problem #1, I resolved problem #2 by sending my cluster over to Relentless Motorsports in Dallas, TX, whom is local to me and does cluster and ECU rebuilds. He is a one man operation who meticulously replaces every chip, resistor, capacitor, and electronic component on the PCB's on a wide variety of classic and modern cars. His specialty is Lexus and Toyota, but he came highly recommended by Erik of U.P.garage since he does the rebuilds for them on GTR clusters.  For those that don't know, on R32 and R33 GTR gearboxes, the speedometer sensor is mounted in the transfer case and is purely an analog mini "generator" (opposite of an alternator essentially). Based on the speed the sensor spins it generates an AC sine wave voltage up to 5V, and sends that via two wires up to the cluster which then interprets it via the speedometer dial. The signal does NOT go to the ECU first, the wiring goes to the cluster first then the ECU after (or so I'm told).  Problems/Roadblocks I first removed the part from the car on the underside of the transfer case (drain your transfer case fluid/ATF first, guess who found out that the hard way?), and noted the transfer case fluid was EXTREMELY black, most likely never changed on my car. When attempting to turn the gears it felt extremely gritty, as if shttps://imgur.com/6TQCG3xomething was binding the shaft from rotating properly. After having to reflow the solder on my AFM sensors based on another SAU guide here, I attempted to disassemble the silicone seal on the back of the sensor to see what happened inside the sensor; turns out, it basically disintegrated itself. Wonderful. Not only had the electrical components destroyed themselves, the magnetic portion on what I thought was on the shaft also chipped and was broken. Solution So solution: find a spare part right? Wrong. Nissan has long discontinued the proper sensor part number 32702-21U19, and it is no longer obtainable either through Nissan NSA or Nissan Japan. I was SOL without proper speed or mileage readings unless I figured out a way to replace this sensor. After tons of Googling and searching on SAU, I found that there IS however a sensor that looks almost exactly like the R33/260RS one: a sensor meant for the R33/R34 GTT and GTS-T with the 5 speed manual. The part number was 25010-21U00, and the body, plug, and shaft all looked exactly the same. The gear was different at the end, but knowing the sensor's gear is held on with a circlip, I figured I could just order the part and swap the gears. Cue me ordering a new part from JustJap down in Kirrawee, NSW, then waiting almost 3 weeks for shipping and customs clearing. The part finally arrives and what did I find? The freaking shaft lengths don't match. $&%* I discussed with Erik how to proceed, and figuring that I basically destroyed the sensor trying to get the shaft out of the damaged sensor from my car. we deemed it too dangerous to try and attempt to swap shafts to the correct length. I had to find a local CNC machinist to help me cut and notch down the shaft. After tons of frantic calling on a Friday afternoon, I managed to get hold of someone and he said he'd be able to do it over half a week. I sent him photos and had him take measurements to match not only the correct length and notch fitment, but also a groove to machine out to hold the retentive circlip. And the end result? *chef's kiss* Perfect. Since I didn't have pliers with me when I picked up the items, I tested the old gear and circlip on. Perfect fit. After that it was simply swapping out the plug bracket to the new sensor, mount it on the transfer case, refill with ATF/Nissan Matic Fluid D, then test out function. Thankfully with the rebuilt cluster and the new sensor, both the speedometer and odometer and now working properly!   And there you have it. About 5-6 weeks of headaches wrapped up in a 15 minute photo essay. As I was told it is rare for sensors of this generation to die so dramatically, but you never know what could go wrong with a 25+ year old car. I HOPE that no one else has to go through this problem like I did, so with my take on a solution I hope it helps others who may encounter this issue in the future. For the TL;DR: 1) Sensor breaks. 2) Find a replacement GTT/GTS-T sensor. 3) Find a CNC machinist to have you cut it down to proper specs. 4) Reinstall then pray to the JDM gods.   Hope this guide/story helps anyone else encountering this problem!
    • perhaps i should have mentioned, I plugged the unit in before i handed over to the electronics repair shop to see what damaged had been caused and the unit worked (ac controls, rear demister etc) bar the lights behind the lcd. i would assume that the diode was only to control lighting and didnt harm anything else i got the unit back from the electronics repair shop and all is well (to a point). The lights are back on and ac controls are working. im still paranoid as i beleive the repairer just put in any zener diode he could find and admitted asking chatgpt if its compatible   i do however have another issue... sometimes when i turn the ignition on, the climate control unit now goes through a diagnostics procedure which normally occurs when you disconnect and reconnect but this may be due to the below   to top everything off, and feel free to shoot me as im just about to do it myself anyway, while i was checking the newly repaired board by plugging in the climate control unit bare without the housing, i believe i may have shorted it on the headunit surround. Climate control unit still works but now the keyless entry doesnt work along with the dome light not turning on when you open the door. to add to this tricky situation, when you start the car and remove the key ( i have a turbo timer so car remains on) the keyless entry works. the dome light also works when you switch to the on position. fuses were checked and all ok ive deduced that the short somehow has messed with the smart entry control module as that is what controls the keyless entry and dome light on door opening   you guys wouldnt happen to have any experience with that topic lmao... im only laughing as its all i can do right now my self diagnosed adhd always gets me in a situation as i have no patience and want to get everything done in shortest amount of time as possible often ignoring crucial steps such as disconnecting battery when stuffing around with electronics or even placing a simple rag over the metallic headunit surround when placing a live pcb board on top of it   FML
    • Bit of a pity we don't have good images of the back/front of the PCB ~ that said, I found a YT vid of a teardown to replace dicky clock switches, and got enough of a glimpse to realize this PCB is the front-end to a connected to what I'll call PCBA, and as such this is all digital on this PCB..ergo, battery voltage probably doesn't make an appearance here ; that is, I'd expect them to do something on PCBA wrt power conditioning for the adjustment/display/switch PCB.... ....given what's transpired..ie; some permutation of 12vdc on a 5vdc with or without correct polarity...would explain why the zener said "no" and exploded. The transistor Q5 (M33) is likely to be a digital switching transistor...that is, package has builtin bias resistors to ensure it saturates as soon as base threshold voltage is reached (minimal rise/fall time)....and wrt the question 'what else could've fried?' ....well, I know there's an MCU on this board (display, I/O at a guess), and you hope they isolated it from this scenario...I got my crayons out, it looks a bit like this...   ...not a lot to see, or rather, everything you'd like to see disappears down a via to the other side...base drive for the transistor comes from somewhere else, what this transistor is switching is somewhere else...but the zener circuit is exclusive to all this ~ it's providing a set voltage (current limited by the 1K3 resistor R19)...and disappears somewhere else down the via I marked V out ; if the errant voltage 'jumped' the diode in the millisecond before it exploded, whatever that V out via feeds may have seen a spike... ....I'll just imagine that Q5 was switched off at the time, thus no damage should've been done....but whatever that zener feeds has to be checked... HTH
×
×
  • Create New...