Jump to content
SAU Community

Recommended Posts

Bloating side will just be my shitty digestive system. I think it *may* be the creatine pulling too much water through into my guts lol.

But yeah, I definitely noticed more energy, focus, strength, etc from it. If I didn't get the sides I spoke of, and it wasn't bad to use a PWO all the time....I'd use it every session haha

I use pre workout every session, I also use creatine every day

Anyway to speed up tendon recovery?

Big weekend on the tools has proved costly. Skipped Monday because I was sore and pulled the pin towards the end of tonights session as the tendon from the back of my elbow to the top of my shoulder is killing me.

Felt mostly around the tricep elbow connection point.

tried the NO3X. The orange/pineapple once is the best tasting pre work out I have had. tastes like berocca.

Started loading up on the creatine as well. No real dramas there. had my 20g before dinner with no issues.

Now just to stick to this over the next 3-4 weeks that I have off

Can't hold squat bar in place without rotating shoulder to use arms = twinge.

Can't hold onto bar to dead without having load go through shoulder = twinge.

Bodyweight lunges maybe? Some swiss ball morning glory things (for back)?

Trying not to even use my arm to drive the car..

Front squats (either arms crossed or in rack position) - neither of these make your shoulder rotate externally.

Bent over BB rows hurt?

Have you tried doing squats with your hands right out at the edge?

squat550.jpg

or dropping your pinkies off the bar?

photo-6.jpg

or thumb over instead of under..

glen23_backsquathigh.jpg

  • Like 1

ActionDan what are you doing for shoulder rehab? Get some Therabands from a physio and maybe a lacrosse ball for "deep tissue massage", light dumbbells also work, for doing "lucky cats" (external shoulder rotations / rotator cuff exercise). Attach the theraband to a door handle or table leg and practise retracting your scapula then drawing your elbow back, keeping it close to the body... these are the sorts of things my physio got me doing after I damaged mine.

Nothing specific for rehab at the moment, just rest, some ice, and avoiding use until the general discomfort goes away.

Not sure if any of those movements will aggravate it TTT, Can give all these things a try though and see. Cheers

depending on what the issue is / exactly what causes the pain, you can find a way around it.

Front squats don't externally rotate the shoulder at all and that's the most common shoulder pain.

Hands out further will make it harder to keep the bar stable but means the shoulders rotate much less.

This shit is pretty good to with really light weight.

Ahh yeah I remember you giving me some good rotator cuff exercises last time (different shoulder issue).

This is, I think, the tendon between my elbow running up the back through the tricep and connecting to the bony point in the shoulder. Most notable at bony point now where as a few days ago most notable toward elbow.

I use maca powder, so good

Maca has to be the best natural supplement i have ever used and probably the only one i have noticed a difference with in a few days. Clear thinking and massive boost in libido. Its some good stuff thats for sure. 2 teaspoons in my oats or a milo with skim milk which i find the tastiest

  • Like 1

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Latest Posts

    • Check the injectors flow evenly, and are actually flowing what you and the ECU think they should be flowing. If it's starting up on starter fluid, you have a fuel issue. Is it possible under cranking your fuel pump is turning off?   The harness you replaced, is that the whole engine harness? Do yourself a test, and drop the old harness on and plug it into the Z32 ECU. It's possible they've wired things different. From memory S1 to S2 is different in RB25 and you may have a wrong loom
    • I haven’t pulled the injectors to watch them spray yet but they are clicking from the cas and all of the spark plugs are wet with fuel. I’ve thought the cylinders were being flooded from the beginning and was hoping fuel pressure would fix it. Tonight I am going to pull the rail and watch the injectors spray. Don’t know how to test/diagnose if the plugs are firing in correct sequence but that should be a timing thing and as far as timing goes my car still has the half moon for the cas can only install it 1 way. And my mechanical timing is 100% correct I posted photos above. Confirmed with the balancer on and off. 
    • I checked spark on all cylinders and they all visually have spark with the plug pulled and grounded, but plug 1 is the only one that fouled. This was a running swap that blew up and was rebuilt by a machine shop, put a new wiring specialties harness and did all gaskets, studs, and bolts while it was out.  compression is 135-150 across all cylinders. Aside from that from my understanding with the z32 ecu and maf the car should start regardless. The wiring for TPS and the dual 02 sensor/ dual knock sensor stuff shouldn’t actually stop the car from starting or even running well, (just slightly rich)  they just give fault codes. Car supposedly is supposed to start as long as you have z32 afm and ecu with the nistune base map and that’s info coming from a well known and trusted tuner who does a lot with SR/RB (Rsenthalpy). After more trouble shooting today where I’m at right now is that the cas is sending signal to the injectors they click while spinning the rotor, Fuel pressure is now set at 43psi, all cylinders have good compression and all of the plugs looked great (just wet with fuel) except for cylinder 1 which was very black (cylinder 1 has 150psi compression). all of the coils generate spark if pulled out and grounded out on the head. On the fuel pump car just pops into the exhaust. On starting fluid car will fire off. Hard to tell if all cylinders are firing off but definitley a couple. sounds like all of them but it’s only for 3-5 seconds hard to tell. 
    • Final update!!! Got the front bar fitted and sprayed and all sorted now. My cutouts worked great and the indicators aren’t just falling off. 😂  
×
×
  • Create New...