Jump to content
SAU Community

Recommended Posts

Just a quick question.

I have just gotten my hands on a rb30det (loom, ecu, turbo all there), with rb25 gearbox, and was planning on stuffing these into my r32 manual gtst. Having basically very little knowledge, and no experience in doing this conversion, I was wondering whether there are any issues with this proposed conversion, or does the engine fit straight in, like a rb25 would?

I am planning on ripping out the rb20det and gearbox out myself, respraying my engine bay and then towing the car to the shop that is going to do the conversion. but to save on time, and any potential hassles, was wondering whether i would need to provide any additional bits and pieces for this. I have purchased some new engine mounts, but apart from that, i can't think of anything else that they might need.

Any help on this would be appreciated, as the car will probably be going in on either monday or tuesday.

Cheers

Link to comment
https://www.sau.com.au/forums/topic/202546-rb30det-into-r32/
Share on other sites

well that's good news. what about all the mounting and bracing underneath? all lines up fine? already got a front facing plenum on it, so should hopefully have no worries. will have to see about the high mount turbo though. might need a new manifold for it

the solution is to modify the Rb20 engine mounts (metal brackets) and cut them down some 20 mm then reweld them up, this will lower the engine to a more desirable height, however the sway bar will foul and the sump will be lower then the crossmember, so spacve the bar down and fit a bashplate and these issues are then nothing to worry about.

I had to remove my strut brace, have a stock 25DE plenum on there and it rubs slightly on the front corner and also slightly on the timing belt cover.. I spaced the back of the bonnet up 10mm so it doesnt try to buckle the bonnet every time I shut it..

Forward facing plenum will go on with the new turbo, all measurements for the GT35R high mount appear that it will clear as it will sit just below the crossover pipe. Will likely "massage" the timing belt cover slightly, don't need to gain much.. 5mm maybe.

Does the 30 have all the ancillaries bolted on? if not you'll need to modify the power steering pump bracket (cut the top boss flush with the lower two), other than that I don't remember anything else that needed modifying (apart from shuffling all the pipework so the bonnet would close!).

Edited by bubba

RB30 did not end up fitting. Mainly due to the design of the front facing plenum on the thing. Stuck up by a couple of centimetres. Could have had another plenum fabricated, but that and the retune would have put my budget out by a fair bit. So rb25 it was. Car will be back on the road on monday at the latest. Trying to source a bloody pfc at the moment that is reasonably priced is proving impossible as well.

also, if somebody in the brisbane area has a r32 2way they are willing to sell, pm me :P

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Seat of the pants assessment of the new intake: The car is way less "doughy" when hitting the loud pedal, especially off idle when stopped or in traffic, I did use a cheapo lazer thermal thingo to measure the temp around where the pod filter got its air, it was between 55 - 60°C, in saying this the car was shut off and not moving, so the OEM intake pipe was not supplying any fresh air to where the pod was when the car was at least moving A weird bonus was induction noise on the throttle in the cabin increased a bit,  I was worried that I was actually going to lose some of that induction noise I love so much, outside though, when I got the daughter to do a WOT drive by pass for me, the induction noise has increased alot when on the throttle, not quite ITB doort, but well up there I'm extremely happy with the results and have been exploring the country roads in the region  As for house mods: 1.New front fence is up and is awesome, it really upgraded how the joint looks from the street, and the added security is nice 2. Electricians have replace some interior lights, and with more lighting in the garage, a few new motion detecting lights out the front above the garage, front room, and at the front door, which I have already found heaps helpful coming and going, also now has fancy pants CCTV all round the house The only hold point for power though is the solar and batteries due to supply issues, although this will happen over the next few weeks 3. I have done a heap of landscaping out the front and I'm almost ready to do a new small retaining wall with some nice blocks to replace the brick and cemented in rocks around the raised garden beds cemented in river stone "was the fashion at the time" the house was built. I currently have a pallet of retaining wall blocks and 2 bulka bags of 20mm blue metal to replace the wood chip that is in the raised garden beds around the house 4. I now have 3 big raised garden beds for out the back to grow some vegetables, about 70cm high, 200cm long and 100cm wide 5. My 2 compost bins are already pretty full with brown, green and kitchen waste from the landscaping I'vedone so far, but they will probably take a few months to break down, so anything else that gets chopped, trimmed, and kitchen waste will just start filling the base of the raised garden beds to about 30cm before I start throwing 40cm of good compost, and stuff, for the vegetables to grow in, I'll need a few ton of compost and soil, but the local supplier can sent me bulka bags of the stuff Basically the logs, wood chips and a few strategically placed rocks for drainage, will give the beds some good organic materials down low to break down over time, and they will hold moisture during the warmer months to save the water in my big arse water tank if we don't get alot of rain So, all in all, the car and house mods are going well, and I'm really enjoying being retired, I sleep in too 0700 and slowly plod around inside until I feel like actually doing anything, and only work in the yard for as long as want, which has actually been alot over the last few weeks,  although when you look at it, it seems that not a huge amount of work has been done,  until I look at the before I started the work pics Happy days and good times indeed 
    • hahaha yeah. Plan is to get side skirts and probably just rear pods. But going to do them one-by-one. I've got a set that I really like from RHDJapen, but that one isn't shipped to AU. So need to find someone who can get it for me
    • Here's an idea, answer the questions I asked you as they are trying to work out WHY the LSD will be binding up in a straight line.
    • You haven't driven many modern cars then have you? Most of them have sfa steering feel with their stupid electric bullshit steering systems.
×
×
  • Create New...