Jump to content
SAU Community

Recommended Posts

Hey there people.

I just recently bought a 1994 R33 Skyline.

It has a Big HKS exhaust and a Greddy Intercooler.

I had a bleed valve fitted and it is runnibg at 11psi, punching out

187RWKW.

I was just wondering what is next to do to it. I just wanna do it and

not have to worry about replacing stuff over and over.

I was hoping for about 350-400+ ATW. The car is off the road for some

of the work to begin.

I am not made of money and I saved for years for this so I am

hoping to do the work myself.

Can you please help me out.

Thanks,

Shaun

post-47374-1202807758_thumb.jpg

post-47374-1202807850_thumb.jpg

Link to comment
https://www.sau.com.au/forums/topic/205754-what-to-do-next/
Share on other sites

350-400RWKW you wont get for any less than $5000- $10000+ on existing engine....

your next mod should be ECU related, either replace with full aftermarket set up and tune $1200-$$$ or look into something like a second hand SAFC piggy back controller $4-500 tuned, good tune on full replacement ECU with 14psi should get you 50-70 extra RWKW depending on the condition of you engine.

you will get better responses in the forced induction section though..

May-be a MOD can just move this thread..

Link to comment
https://www.sau.com.au/forums/topic/205754-what-to-do-next/#findComment-3642945
Share on other sites

350-400kw atw?

Prepare to spend big (c.10-15k) and put up with lots of little issues- especially if the car isn't in tip-top condition. The difference in cost between 250rwkw and 350rwkw is big.

For that power you'll need a forged bottom end, head work (cams, port/polish, valves+springs), fat ass laggy turbo, reworked fuelling system, Power FC, twin/triple plate clutch etc...

I could go on and list the other things, and some of the problems that might arise from working the car so hard (such as maintaining traction)

If you're prepared, patient, well planned, and have the cash you can build an awesome machine. Do some searches in forced induction and drivetrain sections too.

Good luck ;)

Edited by R338OY
Link to comment
https://www.sau.com.au/forums/topic/205754-what-to-do-next/#findComment-3643081
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I've heard the Tomei USA head gaskets are decent if you want to o-ring the heads but otherwise not recommended.
    • The 296mm rotors are the R33 turbo brakes. The 310mm rotors are the R34 turbo brakes. The calipers are nearly the same, but not. They're the same caliper but the R34 caliper has longer legs so that it sits out far enough to go over the rotor. The pads are the same for both. When you say, "I bough tsome EBC"....did you just mean pads? Or rotors? 310mm rotors fit under 17" wheels. There may be some wheels without enough clearance though. I can't fit my fingers between the barrel of my wheel and the "corners" of my R34 calipers, but there is plenty of room behind the spokes. This is on Enkei RPF1. You can fit 324mm rotors inside a 17" wheel, but I'd be willing to bet that it would be close to impossible with the Nissan/Sumitomo caliper (using an adapter, of course), because the Sumitomo caliper is fatter than the Brembo caliper that is supposed to go on the 324mm rotors.
    • Hi. Can someone tell me what brakes(and mainly WHERE) can i buy brakes on R34 GTT? I bought some EBC which SHOULD go on my car(i have GT but it has GTT brakes) but it does not fit, Brakes are "too" small(296mm) Are 310mm be good or? I have 17 inch wheel so no "big boys" but for me driving i just need one that fits and i can get here in EU/Czech.
    • Since winter isn't that harsh anymore in Poland, i will definetely drive it 365 days a year 😉. But if the snow hits i will try it for sure and let U know. Only swap i am planning to do is of course R34 GTR front 😍.
    • Hey. Very valuable information about pitwork, I will pay attention when buying any consumable parts 🙏 As for the carpets - I got a handful of information from nengun, from which it appears that indeed the carpets for the driver's side are OEM. They are not able to show me any pictures due to the long chain of different sales entities but after I place the order, as soon as the goods arrive at the nengun warehouse from which they will send the shipment to me they can send me photos and if my purchase differs from OEM I can immediately return it / cancel the purchase. I think I will give it a try 😉. Of course i'll let you know what's what as soon as i get them P.s. I know the topic is not relevant to the thread, but both nengun and amayama have these SICK 😍 trunk room lamps available. Do you know anyone who ordered them? I need to have one in my car
×
×
  • Create New...