Jump to content
SAU Community

Recommended Posts

Been ages since I dropped in on the Norris brothers. Must get down there again one day.

Spotted their display, but didn't see neither brother.

theres only anthony there now...the boys had a big punch up a couple of years ago...now paul runs hils own milky business...you know what its like...two brothers always arguing whos better..etc etc

theres only anthony there now...the boys had a big punch up a couple of years ago...now paul runs hils own milky business...you know what its like...two brothers always arguing whos better..etc etc

Bloody hell! Oh well, Anthony was always more into it with his drag racing 1600 and all that. Might be getting another 1600 by the end of the year, so I'll be seeing more of Anthony again.

Spotted Purple 33 GTR near my house on the weekend, GTR 888, seen it there quite a few times, looks good!

Saw the gayest car this morning on Anzac Hwy, Silver Mirage with a huge Veilside style front bar with pink mesh, what looked like 13" mags n a bright pink sticker on the front window.. "It's Illegal To Be This Cute"

Spotted Purple 33 GTR near my house on the weekend, GTR 888, seen it there quite a few times, looks good!

Saw the gayest car this morning on Anzac Hwy, Silver Mirage with a huge Veilside style front bar with pink mesh, what looked like 13" mags n a bright pink sticker on the front window.. "It's Illegal To Be This Cute"

Its illegal to be so gay and revolting :banana:

Spotted an extremely tough looking Silver 350Z with what looked like TE37's this arvo on Grand junction Rd

I don't think I've said it in the SA section but I'm pretty sure I've said it elsewhere, 99% of body kits DESTROY the look of a car because 99% of kits are gay. Each to their own though.....

spotted a nice sounding looking stag in pearl, boost works sticker on the back window chick driver near noarlunga

spotted a flawless r31 4dr in seaford, p plater , my r31 rego i think? very nice car

a wine r33 with gtr wing at noarlunga, no end plates driven buy a older bald guy, about 55ish?, kids stopped him to discuss his line, seemed nice guy interested in built skylines. anyone know him?

lots of cops out on the prowl

Spotted a Sh!t load of cop cars down my way :D . Looking for a black car with 3 guys in it, as they were seen driving away from a fire (just started... lil bit sus). Havnt seen soooo many is ages, bit scary lol!

Saw a really nice seriesIII silver 33 GTR today around 5:00pm in Salisbury, plates were GTR-033. And a maroon Cefiro turning off Bridge rd around 6:30pm

Edited by Jamesrb25

Spent all day driving around town in the N1 and spotted 0 Skylines! I swear my car scares everyone away!!

Spotted something cool the other day though - a VX Commodore Equipe with the plates [EQUIPT]...oh dear...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • OK, Step 3, if you need to remove the valve body, either to replace it, the TCM, or to do a more complete drain.  First, you need to disconnect the TCM input wires, they are about half way up the transmission on the drivers side. One plug and the wires are out of the way, but there is also a spring clip that stops the socket from sliding back into the transmission. On my car the spring clip was easy to get, but the socket was really stuck in the o-ring of the transmission housing and took some.....persuasion. You can see both the plug to remove (first) and the spring clip (second) in this pic Incidentally, right next to the plug, you can see where the casting has allowance for a dispstick/filler which Nissan decided not to provide. there is a cap held on with a 6mm head bolt that you can remove to overfill it (AMS recommend a 1.5l overfill). Final step before the big mess, remove the speed sensor that is clipped to the valve body at the rear of the box.  Then removal of the Valve Body. For this the USDM Q50 workshop manual has a critical diagram: There are a billion bolts visible. Almost all of them do not need to be removed, just the 14 shown on the diagram. Even so, I both removed one extra, and didn't check which length bolt came from which location (more on that later....). Again it is worth undoing the 4 corners first, but leaving them a couple of turns in to hold the unit up....gravity is not your friend here and trans oil will be going everywhere. Once the corners are loose but still in remove all the other 10 bolts, then hold the valve body up with 1 hand while removing the final 4. Then, everything just comes free easily, or like in my case you start swearing because that plug is stuck in the casing. Done, the valve body and TCM are out
    • OK, so if you are either going for the bigger fluid change or are changing the valve body which includes the Transmission Control Module (TCM), first you should have both a new gasket 31397-1XJ0A and a torque wrench that can work down to 8Nm (very low, probably a 1/4 drive one). You can probably get by without either, but I really didn't want to pull it all apart together due to a leak. First, you now need that big oil pan. The transmission pan is 450 long x 350 wide, and it will probably leak on all sides, so get ready for a mess. There are 24x 6mm headed bolts holding the pan on. I undid the 2 rear corners, then screwed those bolts back in a couple of turns to let the pan go low at that end, then removed all the middle bolts on each side. Then, undo the front corner bolts slowly while holding the pan up, and 80% of the fluid will head out the rear. From there, remove the remaining bolts and the pan is off. You can see it is still dripping oil absolutely everywhere...it dripped all night.... I got another couple of litres when I removed the pan, and then another few when I removed the valve body - all up another 4l on top of the 3 already dropped in step 1.
    • Yeh I think i'll message an old contact i had for ages that manages his own tyre shop now.. n tell him what i want n work with him before ordering..  Got this 17x9 +30 Driftteks on 245/45/17 PSR Drag Radials on the rear.. They fit well - for your reference in future - Rear guards  have been lipped in & minimal to non flaring of the rear Gaurds.    
    • If only it were that easy! I also needed to remove seats, shocks, brake calipers, send my car through a fence, and use measuring and ended up guessing because I didn't remove seats, shocks and brake calipers. It can be hard sometimes Can be a little more complex than 'just measure' if you want to truly measure the entire wheel through all of it's suspension travel. But if you aren't going for every last mm then yeah, you can check the space you currently have and guesstimate.
    • If you own a car, and it has wheels on it, and you know the offset of those wheels, and you have a measuring device, you have everything you need to work out if other wheels will fit.
×
×
  • Create New...