Jump to content
SAU Community

Recommended Posts

Just a few things i was hoping some of you might be able to help me on. My rb20 in my silvia is only getting roughly 330klms out of a tank. The tank size is 55L. This was with relatively easy driving etc. Also, the cars idle rises and falls dramatically sometimes at idle. Does anybody have any ideas what i should be looking for as to fixing this problem? All the rb has done to it is a k & n air filter which came off the old engine that was in it. Thanks for your help.

Jase

Link to comment
https://www.sau.com.au/forums/topic/20762-rb20-probs/
Share on other sites

Check the idle control valve, or whatever its called, on the back of the plenum. Pull it off and hit it with carby cleaner. They tend to clog up a bit and cause a fluctuating idle.

That economy is pretty bad, I get min 400kms per tank local driving with filter, exhaust, intercooler, boost controller and i don't really drive slow. Up to 530km on longer distance driving.

This is generally taking 53-55L when i fill it up. RB20T aswell.

Link to comment
https://www.sau.com.au/forums/topic/20762-rb20-probs/#findComment-437744
Share on other sites

I would almost bet my left whatever that its your oxygen sensor. I had the same problem with my car, disconnect it and see if it idles better. When i got a new one, the idle was perfect and a big difference in fuel economy (I had to disconnect the faulty one till i found the new one)

Link to comment
https://www.sau.com.au/forums/topic/20762-rb20-probs/#findComment-438853
Share on other sites

I think the problem has been solved. My ignition timing so was retarded it wasn't funny. Now it seems to be very conservative on the petrol and is going heaps harder!! Still have the occasional up and down idle tho so i will take that valve off and give it a clean. For all your rb20det people, i peaked power at 7200rpm, does this sound normal??? The dyno i was on was a bit out of whack too cuz i only got 73kw's at the wheels!!! hehe.

Link to comment
https://www.sau.com.au/forums/topic/20762-rb20-probs/#findComment-439254
Share on other sites

Yeah, I had the same problem after my conversion. While doing the conversion, in an effort to work out why I wasn't getting ignition, I mucked around with the crank angle sensor and when I finally got it going, it was retarded so on idle, it would nearly cut out then rise then nearly cut out again, one of the first things I checked was the CAS and this solved the problem.

Link to comment
https://www.sau.com.au/forums/topic/20762-rb20-probs/#findComment-447281
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Has equal chance of cleaning an AFM and f**king an AFM. I think you can work out what happened. When the Hitachi ECU sees the AFM die and goes into the associated limp mode, then it will start and run just fine, because it ignores the AFM and just runs on idle maps that will do what it needs to get it going. But there is no proper load signal, so that's about all it can do. My suggestion? If you don't want to go full aftermaket ECU, then get some R35 GTR AFM cards and some housings to put them in, in the stock location, and Nistune the ECU. Better to do a good upgrade than just replace shitty 40 year old tech with the same 40 year old tech.
    • So my car was recently having trouble starting on initial crank, I would need to feather the gas for it to start up but besides that it would start and run fine. So I clicked the idle air control valve (with throttle body cleaner) and cleaned the MAF sensors (with MAF cleaner). The start up issue was fixed and now the car turns over without the assist of the throttle, but the car is in limp mode and wont rev past 2.5k RPM. From what I understand the IACV would not put the car in limp mode, so I am to believe it is the MAF sensors, but it was running fine before and now I cant get it out of limp mode. I cleaned the MAF made sure the o rings were seated properly. Made sure the cables were plugged in properly, the cables also both read the same voltage. Does anybody know why this is or what could be causing this or how to get it out of limp mode?
    • Ooo I might actually come and bring the kids, however will leave the shit box home and take the daily
    • Thanks. Yeah I realised that there's no way I'd be able to cover the holes with the filler, it would just fall through. Thanks again @GTSBoy!
    • That was the reason I asked. If you were going to be fully bodge spec, then that type of filler is the extreme bodge way to fill a large gap. But seeing as you're going to use glass sheet, I would only use that fibre reinforced filler if there are places that need a "bit more" after you've finished laying in the sheet. Which, ideally, you wouldn't. You might use a blob of it underneath the sheet, if you need to provide some support from under to keep the level of your sheet repair up as high as it needs to be, to minimise the amount of filler you need on top. Even though you're going bodge spec here, using glass instead of metal, the same rules apply wrt not having half inch deep filler on the top of the repair. Thick filler always ends up shitting the bed earlier than thin filler.
×
×
  • Create New...