Jump to content
SAU Community

Recommended Posts

Guest Rhino

Us WA ppl are in the middle of organising a trip down to the Motorplex in the next couple of weeks and I was looking for advice on launch techniques for a R32 GTR.

I have dialed up 5,000rpm on the street and it bogs, whereas 6500rpm is pretty good in my opinion. What is a good launch rpm for a proper strip?

I want the GTR's first run session(not to mention mine) to be a good, fast and safe outing. I hope redline launches aren't going to to be the order of the day as I'd prefer not to rape my car to get a good time when a sensible approach will net a good result.

Fingers crossed for 12's.

Cheers,

Ryan.

Link to comment
https://www.sau.com.au/forums/topic/2079-gtr-strip-launch/
Share on other sites

  • 2 months later...

From memory there was a .30sec reduction in ET by increasing launch rpm from 5,500 - 7,000rpm, terminal speed went up by 4 - 6kph as well.

7,000 launches give a fair whack of wheel spin and spinning in 2nd was also common, depending on whether I got the shift to 2nd right.

I did 4 13.0xx sec passes in a row with my old clutch which was a factory item about half worn with a dodgy flywheel face. The MC day the Perth people had last Sunday was my first chance to flog the new clutch and it has proven to be pretty bloody good for a clutch that isn't any harsher or harder to drive than the factory unit.

The day at the drags was good, but no 12sec. passes just lost of 13.0's!! That was with the old clutch slipping a bit and 50L of fuel on board. Next time 1/4 tank of fuel and I'll have a 12sec timeslip in my pocket.

Cheers.

Link to comment
https://www.sau.com.au/forums/topic/2079-gtr-strip-launch/#findComment-69798
Share on other sites

heres ulas results

1st run...

5 grand dump, as i usually do on the street.

60 foot - 2.024

ET - 13.129

MPH - 106.52

2nd run...

i thought that i was wheelspinning too much off the line so i took off at a 4 grand dump (wrong thing to do!)

reaction time

60 foot - 2.310

ET - 13.903

MPH - 104.61

3rd run...

on this run, we all decided that i just launch at a 7 grand dump. the car rocketed!

60 foot - 1.881

ET - 12.776

MPH - 107.41

Link to comment
https://www.sau.com.au/forums/topic/2079-gtr-strip-launch/#findComment-69803
Share on other sites

ok cool... have u had it tuned?

ula had his tuned at the dyno day we had not long ago... cant remember the mods he has but its nothing outrageous but i remember he was getting 210rwkw or around 275rwhp.

hes running the stock GTR rims and not sure on the tyres

Link to comment
https://www.sau.com.au/forums/topic/2079-gtr-strip-launch/#findComment-69818
Share on other sites

heya Rhino... my rims are standard with crappy 225 rubber on them. clutch has also been upgraded but mines only a cat back exhaust. our theory was that you have to get the rear wheels to spin so the computer picks it up and then moves power to the front wheels which gets you the better take off, hence the 7000 dump. i wasn't game to try the rev limiter dump (only on gran turismo 3 hehe :) ) i know that my times wouldnt improve unless i had better and wider rubber. hope you get a good time!

Link to comment
https://www.sau.com.au/forums/topic/2079-gtr-strip-launch/#findComment-69834
Share on other sites

Hey Guys,

Use the rev limiter. Thats what it's there for!

The best way to get consistent launching is to take off the same

every time.Hold the revs up around 5-6000 then when the first

amber comes on flatten it and watch for the green.The trick is not

to sidestep the clutch(which will create problems-trust me) but to

ease it off with a little bit of slip.You must hold the car on the line

with the handbrake(or a line locker)to take up the slack in the

driveline.I have smashed std driveshafts, diff output shafts,3 gearboxes, & recently an HKS driveshaft!!! It just takes practice.

You shouldn't start breaking things until you pass 300rwkw, so if

your GTR is stock or mild give it heaps.Biggest problem is tyres.

Old, hard road tyres will not hook up.Borrow some sticky ones,

do big burnouts, experiment with tyre pressures,etc.

Drag racing GTRs is great fun.

I took out my R34 which only has exhaust & apexi power FC and

ran 12.1 @ 115mph! Don't over rev it. If your car is not making power over 7000rpm change gears earlier - it will run faster.

Have fun.

P.S. I have a mate over there with a GTR torana.Runs mid nines!!!

Link to comment
https://www.sau.com.au/forums/topic/2079-gtr-strip-launch/#findComment-69851
Share on other sites

Yep,

I do drive my R34 that hard.It's the only way to get it off the line

properly without bogging.Check out the Jap guys.You always hear

them popping on the rev limiter before they launch.:burnout:

Go hard or Go home.With the R33(OS 3 Litre engine) I sit on

9000 rpm for at least 5 seconds before launch to build up the boost.Any 4WD with a small capacity turbo engine needs revs to

launch hard.They don't have much bottom end torque, so if you

come off the clutch too early you bog the engine, lose torque, &

lose time. It is much easier to launch a V8 because they have so much torque.My old HJ holden ute (350 chev) used to launch at

4-4500rpm, run a 1.4 60ft, & 10.1 @ 133 mph.Also most V8s use

a trans & torque convertor which multiplies the torque & literally

slingshots the car off the line.

We are doing it the hard way with Hi-tech, multivalve,turbocharged,small capacity engines - & using solid clutches & manual gearboxs plus hard street suspension/steet tyres.It is much harder than old school drag racing, but it is a challenge, and it is great fun.Dropping the clutch at full revs, changing 4 or 5 gears,keeping the engine on boost,and all the while trying to keep the car off the wall is very entertaining!

There is no doubt that V8s are king of competition drag racing,

but you try and drive a 10sec V8 car on the street reliably.

This is where Hi-tech comes into it's own.They handle well, go like stink,behave on the street in traffic,& have all the creature comforts.Go skylines!!!

:uh-huh:

Link to comment
https://www.sau.com.au/forums/topic/2079-gtr-strip-launch/#findComment-71271
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • You can use your VIN to look up the factory part number somewhere like amayama, and then look to order new if necessary. https://www.amayama.com/en/genuine-catalogs/nissan Depending on price you might want to rebuild instead. @GTSBoy I had an interesting insight into US market parts when the Titan rear calipers were sticking. New calipers were dirt cheap, about 20% more than a rebuild kit....they are just considered throw away maintenance items
    • Funny, but really not funny. Thank god (most) f the world has moved on since then
    • Lots of votes for driving onto a plank first; that is the quickest way I've found, 25mm is enough for my case but that will vary by car It also depends where you are going for. On the 32 I can get to the rear diff with my floor jack if I do that end first, and get it up on stands. Then I lift the front from either front tow hook as high as needed, also onto stands. Sometimes I need a small lift on the other tow hook to get it level enough If I do the front first I can't get to the rear diff because of the angle of the car Other options are getting to the front mount of the rear subframe from in front of the wheel (if only lifting one side, or just do both which is a bit of a pain compared to one lift from the diff), or also the gearbox cross member mount on the driver's side if you are  just trying to lift the driver's side. I This is the jack I use; it says 75mm clearance but of course that is only on the lower section so if you have to reach too far in like the diff you still get stuck. https://www.snapon-bluepoint.com.sg/category/Floor-Jacks/product/Floor-Jack,-2-Ton-Low-Profile
    • On the bright side, the weather will turn much nicer for working outside shortly....sounds like you might need to start on a neighbour's garden next
    • Ok so i will NEED to have this sensor anyway even with Nistune (or standalone ECU) https://justjap.com/products/genuine-nissan-boost-pressure-sensor-evap-control-system-fits-nissan-r34-skyline-c34-nm35-stagea-pnt30-x-trail-rb25det-vq25det-sr20vet?currency=AUD&srsltid=AfmBOoqfxX48bW9bEwH62orcNhtBfp7ekAL0C9Ca89ySFGUiBzXfXeze Is this the correct one? And this is only thing i need? No other "things" connected to the sensor or something? I do have the wiring.
×
×
  • Create New...