Jump to content
SAU Community

Recommended Posts

You can keep the RB26 aac valve, but you have to change to the RB26 oil cooler set up. Also, the RB26 plenum will not clear the VVT solenoid on the side of the motor. It hits a coolant passage, so you either have to do non-vvt cams, or do some grinding/aluminium welding.

Throttle response is pretty cool though :cheers:

im just back from the workshop and we've got it fitting perfectly.

however as you said the vct solenoid & plug does hit the mani so it has to be cut and a piece of angle bar welded onto it. also one of the sensors needs to be moved to the underside of the mani. also the water outlet pipe (the bottom one) needs to be rotated anticlockwise (the hose still fits however).

you can use the rb25 aac, but it needs to be relocated - a bracket will be included in the kit (bolt onto the top 2 engine mount bolts)

clearance between the plenum and the brake booster/clutch cylinder and shockie tower is actually pretty good, id say more clearance than in a gtr

i'll get some pics tomorrow and upload them :thumbsup:

im just back from the workshop and we've got it fitting perfectly.

however as you said the vct solenoid & plug does hit the mani so it has to be cut and a piece of angle bar welded onto it. also one of the sensors needs to be moved to the underside of the mani. also the water outlet pipe (the bottom one) needs to be rotated anticlockwise (the hose still fits however).

you can use the rb25 aac, but it needs to be relocated - a bracket will be included in the kit (bolt onto the top 2 engine mount bolts)

clearance between the plenum and the brake booster/clutch cylinder and shockie tower is actually pretty good, id say more clearance than in a gtr

i'll get some pics tomorrow and upload them :cheers:

Noice work Ninja. Cant wait to see it. :thumbsup:

im just back from the workshop and we've got it fitting perfectly.

however as you said the vct solenoid & plug does hit the mani so it has to be cut and a piece of angle bar welded onto it. also one of the sensors needs to be moved to the underside of the mani. also the water outlet pipe (the bottom one) needs to be rotated anticlockwise (the hose still fits however).

you can use the rb25 aac, but it needs to be relocated - a bracket will be included in the kit (bolt onto the top 2 engine mount bolts)

clearance between the plenum and the brake booster/clutch cylinder and shockie tower is actually pretty good, id say more clearance than in a gtr

i'll get some pics tomorrow and upload them :cheers:

cool, would love to see pics :thumbsup:

i have just order my kit from japan so should be here within the week hopfully i can do the swap in a weekend if not i might just wait till a buy another daily

however as you said the vct solenoid & plug does hit the mani so it has to be cut and a piece of angle bar welded onto it. also one of the sensors needs to be moved to the underside of the mani. also the water outlet pipe (the bottom one) needs to be rotated anticlockwise (the hose still fits however).

clearance between the plenum and the brake booster/clutch cylinder and shockie tower is actually pretty good, id say more clearance than in a gtr

I'm pretty surprised you said there is more clearance. Mine is tight as a frogs butt.

Wait, you are putting this in a R33, huh? I've got a RB25 in my R32, so you must have a ton more room.

Just FYI there is a SAU Vic car (Red 32) in latest autosalon magazine using the RB26 setup on 25 head

Go see ben at race pace he has them, if its like his other work it will be impeccable.

Any word on 20DET Adaptation Shane? Or too hard basket?

farken whoops. forgot all about it.

it SHOULD be similar to the 25 setup, with a change of bolt location on the first plate.

where are you located? i'd ideally like to have the car on hand to make sure it all fits. i'll PM u my number so we can have a chat about it - i have a few ideas

QUOTE(dano4127 @ 28 Feb 2008, 12:17 PM)

Just FYI there is a SAU Vic car (Red 32) in latest autosalon magazine using the RB26 setup on 25 head

Go see ben at race pace he has them, if its like his other work it will be impeccable.

Yeah thats my R32.

What do you need to know.

Im verry happy with it. It gives killer response and 40hp straight up.

Understand that Gready pleniums have stuff all responce and have no performace advantage untill about 450kw so there great for drag thats it.

Adz, what size huffer you using mate? All indications are the 20 won't pull enough air through so keen to know the performance on yours, especially at low boost, part throttle, low rpm. Good one BTW :)

Im running a RB25 with a GT3582 or GT3540 in the old language.

Wouldnt recomend the rb26 set up on a 20 head.

Car feels great at all rpm and runns about 15psi. It just feels like it wants to get up and boogy all the time.

any idea when the kit will be available to purchases?

as after exchanging emails with the Japaneses supplier, they said some parts need to be changed and welded :D which i'm not very keen on, Does your kit required anything similar or is it just a swap setup?

and will you be running an adopter to use the rb25 acc value or adopter to run the 26 acc value on the 25?

wish you were located in perth :D

Edited by [Michael]

atm im waiting on the admins on here to get back to me as i need trader status. That was over a week ago when i asked them.

if you want to retain your VCT, then there will be some welding required (look at the pics in post 66, near the vct solenoid)

no adapters need to be used for the aac :down:

atm im waiting on the admins on here to get back to me as i need trader status. That was over a week ago when i asked them.

if you want to retain your VCT, then there will be some welding required (look at the pics in post 66, near the vct solenoid)

no adapters need to be used for the aac :)

what are the benefits of retaining the VCT? and is it as simple as removing that section of the gtr plenuming and welding the gts-t part on?

what are the benefits of retaining the VCT?

"V-TEC just kicked in....YO!!" :)

Basically you get the cam and mapping responding to whatever computer you use to change the inlet timing relative to the engine RPM.

So on my race car, with no VCT but using GTS25t PFC I have the VCT set to over 10,000 RPM, so nothing changes at all.

I haven't looked hard enough to know about the welding.

"V-TEC just kicked in....YO!!" :)

Basically you get the cam and mapping responding to whatever computer you use to change the inlet timing relative to the engine RPM.

So on my race car, with no VCT but using GTS25t PFC I have the VCT set to over 10,000 RPM, so nothing changes at all.

I haven't looked hard enough to know about the welding.

interesting, where on the pfc h/c does it show the VCT setting, as i might have alook see at mine

interesting, where on the pfc h/c does it show the VCT setting, as i might have alook see at mine

You have to have datalogit and the software. You can't get to it in the hand controller.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Can I suggest you try EBC directly again and link them to as many competitor catalogues as you can to show their listing is incorrect, eg https://dba.com.au/product/front-4000-series-hd-brake-rotor-dba42304/ If you have access to an R33 GTST VIN and your VIN, you could also use a Nissan Parts lookup like Amayama to show them the part number is different between 33 GTST and 34 GTT which may get their attention
    • So i got reply from EBC and they just this site where you can clearly see those 296mm fronts on R34 GTT. I send them photos and "quotes" that 296mm are not for 34 GTT and they are too small. But it will be very hard to return them cuz nobody here knows 100% and they just copy those EBC catalogue :-D https://ebcbrakesdirect.com/automotive/nissan/skyline-r34
    • Hi, is the HKS  Tower Bar still available ? negotiable ? 🤔
    • From there, it is really just test and assemble. Plug the adapter cables from the unit into the back of the screen, then the other side to the car harness. Don't forget all the other plugs too! Run the cables behind the unit and screw it back into place (4 screws) and you should now have 3 cables to run from the top screen to the android unit. I ran them along the DS of the other AV units in the gap between their backets and the console, and used some corrugated tubing on the sharp edges of the bracket so the wires were safe. Plug the centre console and lower screen in temporarily and turn the car to ACC, the AV should fire up as normal. Hold the back button for 3 sec and Android should appear on the top screen. You need to set the input to Aux for audio (more on that later). I put the unit under the AC duct in the centre console, with the wifi antenna on top of the AC duct near the shifter, the bluetooth antenna on the AC duct under the centre console The GPS unit on top of the DS to AC duct; they all seem to work OK there are are out of the way. Neat cable routing is a pain. For the drive recorder I mounted it near the rear view mirror and run the cable in the headlining, across the a pillar and then down the inside of the a pillar seal to the DS lower dash. From there it goes across and to one USB input for the unit. The second USB input is attached to the ECUtec OBD dongle and the 3rd goes to the USB bulkhead connected I added in the centre console. This is how the centre console looks "tidied" up Note I didn't install the provided speaker, didn't use the 2.5mm IPod in line or the piggyback loom for the Ipod or change any DIP switches; they seem to only be required if you need to use the Ipod input rather than the AUX input. That's it, install done, I'll follow up with a separate post on how the unit works, but in summary it retains all factory functions and inputs (so I still use my phone to the car for calls), reverse still works like factory etc.
    • Place the new daughterboard in the case and mount it using the 3 small black rivets provided, and reconnect the 3 factory ribbon cables to the new board Then, use the 3 piggyback cables from the daughterboard into the factory board on top (there are stand offs in the case to keep them apart. and remember to reconnect the antenna and rear cover fan wires. 1 screw to hold the motherboard in place. Before closing the case, make a hole in the sticker covering a hole in the case and run the cable for the android unit into the plug there. The video forgot this step, so did I, so will you probably. Then redo the 4 screws on back, 2 each top and bottom, 3 each side and put the 2 brackets back on.....all ready to go and not that tricky really.      
×
×
  • Create New...