Jump to content
SAU Community

Recommended Posts

i have a stall problem on my S2 so i took the kick pannel off the passenger side got the ecu out to do the diagnostic check. swiched the ignition on and no lights, on closer inspection there is the holes to view the lights and a hole for the screw but none of its there is ther any other way to do this with out a consult unit.

and why dont i have lights????

Edited by xr8eater
Link to comment
https://www.sau.com.au/forums/topic/210274-diy-to-do-diagnostic-on-an-r33-s2/
Share on other sites

My R33 S2 doesn't have lights on it's ECU either but at least mine doesn't have holes like the one you described. I haven't seen R33 Ecu having lights yet though. Most of the ECU i've seen are the concealed type.

You have to switch the car to the right diagnostic mode by shorting some terminals on the diagnostic plug. Its all in the workshop manual

That probably wont help with your stall issue, clean afm, aac etc. and go from there

ok after alot of messing about

i will finaly give you guys a way to do a diagnostic on an S2 with no lights on the eccs

first find the consult plug in the fuse bos next to the steering wheel as in pics

post-13070-1205647285_thumb.jpg

next remove the plug end and turn your car to the on position dont start it

post-13070-1205647395_thumb.jpg

get a paper clip and insert into only the holes shown for 2 seconds and remove

post-13070-1205647516_thumb.jpg

post-13070-1205647551_thumb.jpg

your engine check light should start to flash a series of codes

ECU Diagnostic Codes

11 Crankshaft position sensor

12 MAF sensor circuit (air flow meter)

13 Coolant temperature circuit

14 Vehicle speed sensor circuit

21 Ignition circuit

31 ECU (ouch!)

34 Knock sensor

43 Throttle position circuit

45 Injector leak

51 Ignition circuit

54 Auto signal to ECU

55 All OK

Turn the ignition off to put the ECU back to normal and clear all faults.

to check the o2 sensor follow the prompts above but dont tun the ignition off just start the car the check light will flash off for rich on for lean.

Edited by xr8eater
  • 2 weeks later...

did the diagnostic test which worked perfrectly.... came upp with no. 12 afm prob.

my consult plaug didnt have the black plug connected in it, is just opened....

also are r33 s1 ecu identical with their terminal connector numbers as a r33 s2.

I need to check the continuity of terminal no. 26 & 27 which relate to the afm sensor wires.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hi...a bit a "development" on the brakes. I spoke to the guys where i get brakes from...and they are saying that 296mm EBC are for R34 GT-T. I then went to their site: https://www.ebcbrakes.com/vehicle/uk-row/NISSAN/Skyline (R34)/ and search for my car(R34 GT 1998 - it has GTT brakes) and it show me this USR1229 number and they are rly 296mm rotors... So now iam rly confused... The rotors i have now on the car are 310mm asi shown... So where is the problem? Does the whole EBC got it wrong or my calipers are just...idk know what?  
    • Oh What the hell, I used to get a "are you sure you want to reply, this thread is XX months old" message. Maybe a software update remove that. My bad.
    • This is a recipe for disaster* Note: Disaster is relative. The thing that often gets lost in threads like this is what is considered acceptable poke and compromise between what one person considers 'good' looks and what someone else does. The quoted specs would sit absurdly outside the guards with the spacers mentioned and need  REALLY thin tyres and a LOT of camber AND rolling the guards to fit. Some people love this. Some people consider this a ruined car. One thing is for certain though, rolling the guards is pretty much mandatory for any 'good' fitment (of either variety). It is often the difference between any fitment remotely close to the guards. "Not to mention the rears were like a mm from hitting the coilovers." I have a question though - This spec is VERY close to what I was planning to buy relative to the inboard suspension - I have an offset measuring tool on the way to confirm it. When you say "like a mm" do you mean literally 1mm? Or 2mm? Cause that's enough clearance for me in the rear :p I actually found the more limiting factor ISNT the coilover but the actual suspension arms. Did you take a look at how close those were?
    • @GTSBoy yeah sorry i know thery are known for colors bud those DBA are too in colors 🙂 Green will be good enough for me  
    • That's my life. Past-Duncan has a lot to answer for
×
×
  • Create New...