Jump to content
SAU Community

Recommended Posts

Anyone have any overheating issues with their car on these past few days? Mine never had this problem before until a few days ago, my water temp gauge rose to 2/3 of the gauge when it's usually in the middle. So I had to turn off my A/C so that the tempreture can drop back to normal.

I thought my water pump or thermostat was failing since it has never happened in the last 3 years of owning it. But this happened to a friend of mine too so I wasn't sure if it's just the heat or something wrong with my car.

If this is uncommon, then I will take the car out to the mechanic to check. The coolant in my radiator is still full so that wasn't the problem I think.

Link to comment
https://www.sau.com.au/forums/topic/210583-over-heating-issues/
Share on other sites

Also be sure to check your radiator fan for issues, I think thats the source of my overheating issue.

One way to check is get a friend to start the car when its pretty warm. Hold the fan gently, with a finger or similar, do not misinterpret this post to mean shove your hand straight into the fan and see what happens.

If the fan try's to turn with some force then its working.

If its like mine you can hold it with one finger and even after you let it go it takes a while to start spinning again.

Oh, and if you injure yourself by doing this I take no responsibility whatsoever :).

Edited by some_cs_student
Also be sure to check your radiator fan for issues, I think thats the source of my overheating issue.

One way to check is get a friend to start the car when its pretty warm. Hold the fan.

If the fan try's to turn with some force then its working.

If its like mine you can hold it with one finger and even after you let it go it takes a while to start spinning again.

I prob wouldn't recommend stickin your hand in there and cranking the car.....

Also be sure to check your radiator fan for issues, I think thats the source of my overheating issue.

One way to check is get a friend to start the car when its pretty warm. Hold the fan.

If the fan try's to turn with some force then its working.

If its like mine you can hold it with one finger and even after you let it go it takes a while to start spinning again.

You can use something else, for Christs sake don't use your hand lol.

lol, the fans not that hard to hold still when you start the engine, the coupling just slips the same as when the engine is revving which is what keeps the fan at a fairly constant speed. I wouldn't go putting my hand in there when it's already spinning but otherwise.....

I get my coolant changed once a year, just before summer. If you changed yours 30,000km ago, maybe try a full flush. Always best to start simple. Also get a pressure test done on the system to see if you have any leaks and if you have time pull off your front bar and clean up leaves/crap that's infront of your radiator.

If that doesn't fix it, I'd be looking at the thermostat (replace) or maybe a clogged radiator (flush/rod).

lol man do NOT stick your hand in ther

dumbest idea ever

I've done it on 2 different cars, and I'm fine.

I don't mean put your entire hand into the fan, I mean touch the end of the fan blade and start it, if it pulls away from you then its working.

Of course if you're stupid enough to put your entire hand in there then you've misinterpreted my advice.

Also see if its spins after you turn the engine off after its warmed up, my fan spins for a long time...

Also be sure to check your radiator fan for issues, I think thats the source of my overheating issue.

One way to check is get a friend to start the car when its pretty warm. Hold the fan gently, with a finger or similar, do not misinterpret this post to mean shove your hand straight into the fan and see what happens.

If the fan try's to turn with some force then its working.

If its like mine you can hold it with one finger and even after you let it go it takes a while to start spinning again.

Oh, and if you injure yourself by doing this I take no responsibility whatsoever :P.

LOL... ...try sticking your dick in there... *clacka clacka clack* ;)

LOL... Well.. you guys can try sticking your dick in there if you want.. but I used a branch and tried to put it in slowly.

It smacked my stick away so I'm assuming that my fan is still strong and it feels like its blowing hard.

Maybe I will try a flush first and see how it goes from there.

LOL... Well.. you guys can try sticking your dick in there if you want.. but I used a branch and tried to put it in slowly.

It smacked my stick away so I'm assuming that my fan is still strong and it feels like its blowing hard.

Maybe I will try a flush first and see how it goes from there.

Did you put the branch in while its spinning?

Or did you try putting the stick on it when you started it? If it pushes the stick out from idle when it starts moving then your fine, just don't drop the stick into the fan. lol.

Good luck with fixing the issue.

you gotta put in fact as well that the jap cars such as skylines werent made for Australian weather also, mechanic told me that one time and that could be one reason for it as well some one correct me if im wrong.

Japanese weather does not hit these one off hot days, but it does get very hot and humid for weeks at a time... That is why Japanese cars have much better cooling systems and air conditioners than Euro cars of the same age.... Most of us own cars that are over 10 years old, you have to expect them to get a bit upset when it gets hot...

Citroen CX aircon was so weak, that for Japanese and Australian markers, twin air conditionsers were fitted.... They added another one in the boot... It is also once of the reasons that the Commodore grew away from the Opel versions they were based on from the VL. Holden needed more space for the larger Aus spec air con units.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • CTIS (Central Tire Inflation System) has existed since the 80's. I'm looking into buying a Hummer H1 and they generally included it. 
    • My idle is set at 950rpm though - Moving the timing around 20 degrees is not really what I'd call a calm idle. That said... neither is chop, by definition. The LS ECU likes to adjust timing to hold idle as opposed to air. It'd work, but generally speaking there'd be a discrepancy in the base idle and the IACV would want to move the timing around anyway to maintain said idle. I think I'm just going to keep the timing steady anyway. Preserve my engine mounts.  My aircon is now officially regassed. As the guy was reversing I noticed my reverse lights do not operate, along with my reverse cam. This is a bit distressing, because 100% of guides talk about which wire to connect to backup cams as "the goes with the [other color] wire". Often when doing conversions. Unfortunately the R34 colour wires aren't documented Unfortunately I had a T56 Magnum gearbox with it's reverse switch, which also isn't documented. Unfortunately there's definitely not documentation for people with both of these in the one car. Unfortunately I forgot. After many hours of this, I have a reverse cam and reverse lights again. The wire going through the trans tunnel to the reverse switch had broken. Upon inspection, it looks like this one wire had about 7 spade terminals and extensions in it.. for reasons I cannot possibly comprehend. I also spent the 750 hours required to clean up the wiring behind my head unit which now looks like this: This is a monumental improvement relative to what used to be there WRT triple gauges, head unit, traction control, wideband controller, and whatever the f**k OEM stuff still exists there in various states of connectivity/needed. Next step is to check in at the Exhaust shop to see/confirm how much clearance I have, to decide what mid mufflers or 'resonators' (which are just straight through, narrower mufflers) I can add and hopefully cut out a lot of exhaust leaks, pinhole, v-band or otherwise. But first step will be to 'take a look' before the next step.
    • Fark the AFM card and Nistune, Haltech Nexus S3, DBW, cruise control, flex fuel, dis dat.  
    • It's most likely the bolt/bush where the cover bolts back wore and allowed cover to move forward.
    • Still haven't put the injectors and R35 AFM in so we can tune the bloody thing for the HG highflow it got mid last year! I think I can forecast the upgrade path to a bigger twin scroll, external gate, Haltech, flex setup, Samsonas, dis dat, etc will be .... a while away!
Ă—
Ă—
  • Create New...