Jump to content
SAU Community

Recommended Posts

hey guys ive got stock suspension at the moment and pushing around 190rwkw... so would like to looka t handling a bit now, ive removed my hicas fuse because the hicas was pulling me seriously to the left on high acceleration/high speed which was a worry and since i removed the fuse its been fine... i am planning on getting a lock bar soon for that.. but also just wondering with strut bars.. can i just get the cheapest one i can find or are adjustable/better brands really worth the extra ? for my suspensioin i am currently looking into going conia shocks and springs all around

cheers

Link to comment
https://www.sau.com.au/forums/topic/21314-strut-bars-in-r33-gtst/
Share on other sites

strut bars arent really nescesary (spelling) but if u did get one, maybe an aluminium one or sumthing that is not adjustable. expensive ones arent really worth the extra unless its frotrack use mainly. The suspension setup sounds good if ur thinking of koni, otherwise i dont know wat conia is :D

Before I put sways on my car, I put strut bars front and rear and hardly noticed any difference in the car. From my understanding strut bars increase the rigidy of the chassis.

On my WRX when I put one in the front I noticed a slightly better turn in on corner entry though body roll didn't change. Thus you can conclude that the Skylines have a better chassis to start off with which is why there is little difference.

The biggest improvement was the sway bars cause the car is much more sharper on entry and the ammount of roll is reduced.

Strut bars go over the engine bay. Sway bars are underneath the car.

Plus you get more rice factor out of strut bars! :)

I think sways are about 250 or so. If it's for a RWD car you probably only need one for the front suspension. If you want to go do track days then front and rear.

i found a slight difference when i fitted the strut bar in my engine bay, not alot mind u but a lil bit, picked one up for $160 gives it a bit more of a performance look too i reckon...

sway bars not too sure how much there costing atm.

cheers

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • This. A 3d wheel alignment is like $120...just take it to the shop. Since theres probably multiple adjustments that need to be made after changing something. Mine has front/rear lower arms, traction rods, tension rods, camber arms, toe arms, front upper arms, hicas kit, sway bars and coilovers. I measure from the edge of the bolt holes on the originals and set the same length on all the adjustable stuff to dial it as close as I could to OEM. Took it straight for alignment; it didnt feel right at all...after alignment, it feels perfect. Similarly i've just changed the springs on another car; and I still needed multiple adjustments to bring it back in spec.
    • A full Veilside kitted JZA80 Supra in Meriken park in Kobe city a few weeks back
    • Its a well known brand in New Zealand; its a rebrand of the Rhino RAV3.  I don't know what the wiring difference *is* between the rev.1 (installed about 15 years ago) and rev.2; but as you say I would think its reasonable that it uses the same immobiliser relay circuits. I had a look but couldnt see a similar harness; but didnt move things around since I didnt want to mess with it   It was one of AVS well known Authorised Installers; I spoke to AVS themselves about it but theyre unsure hence seeking advice more so from the skyline community who are more familiar with the actual car and its wiring. Im in Auckland; but the installer is on the other side of the city so hes very reluctant to come back to even look at it to confirm something isnt connected into the wrong wire.  I dont want to drop the name since they *did* do a really good job for the most part. Everything is very tidy and he fully replaced all the alarm wiring, all the sensors, the wiring to the door motors, installed a switch which was never installed in the first place...really happy with the alarm install itself..just not this one issue. We all make mistakes, if it is the alarm, I just want my fuel pump getting proper switched, fused, power as it was; without having to shell out for an auto electrician to switch a wire and tell me it was the alarm. 
    • Even with the piston at TDC there was room for it to drop, but I don't think it can drop fully into the cylinder, the problem you have is that you need something pushing against the valve to hold it up so you have enough room to put the new stem seal on and the spring etc.  I used compressed air only because putting rope in the cylinder seemed a bit risky to me, I know people have done it countless times before like this. Overall it's a pain in the ass job. Honestly you'd probably be better off taking the head off because the risk of dropping something in the engine and the finicky-ness of it all is very stressful. If you are going to attempt it though i 10000% recommend a 36050 valve spring/keeper tool. I had both the traditional lever type and after doing 1 cylinder it was absolute pain to get those valve keepers in place, even with 2 people. That 36050 is amazing, you do have to push hard to get them in place but it works perfectly almost every time. Back to my actual issue I think my engine is just tired and old and the rings have gone bad. The comp numbers (cold, no oil) were: Cyl 1 -129psi Cyl 2 - 133psi Cyl 3 - 138psi Cyl 4 - 137psi Cyl 5 - 157psi Cyl 6 - 142psi   Cylinder 5 and 6 having the most carbon on them.
    • Who did you have do the installation? I actually know someone who is VERY familiar with the AVS gear. The main point of contact though would be your installer.   Where are you based in NZ?
×
×
  • Create New...