Jump to content
SAU Community

Recommended Posts

You will need!!!!

ECU of some description

Fuel pump and Reg so as to max out injectors by raising fuel pressure (not the best way to do things)

FMIC

Exhaust (other wise you are wasting your time)

Bleed valve (boost control of some kind)

Now I would go a z32 AFM as well

also some injectors

Link to comment
https://www.sau.com.au/forums/topic/213155-turbo-question/#findComment-3766788
Share on other sites

17psi on a stock tune could make mince meat of a piston in no time... If you dont have the correct AFR (air fuel ratio) you run a high risk of detonation due to lean fuel and air mixtures.

But you might be lucky, I have heard of people doing it and not having troubles...

However, my advice is to run a maximum of 12 - 14psi with a stock R33 RB25DET computer, if you start running anything over this kind of boost you may have serious issues with your AFR's being far to lean and if you get even a small boost spike without safe mixtures you could easily end up with a piston head with a large chunk missing.

Do it once, do it right...

1st step - Fuel pump (Bosch 040 or Walbro are the most popular)

2nd step - Splitfires (or higher amperage coils) the standard coils dont have high enough amps and with more boost you could end up blowing out the spark at high RPM.

3rd step - Computer and injectors (try not to go over 550cc on a stock motor as they can be a bitch to tune if they're to big) and something like a Power FC plug in or a Microtech would be needed to control the whole kit.

Oh and make sure that you have some sort of reliable boost control and a front mount + big exhaust or you'll just choke a bigger turbo and it wont breathe enough for decent power gains.

Ive been through all of this and unless you know what your doing and can do most of it yourself it can become very expensive.

Happy shopping :P

Link to comment
https://www.sau.com.au/forums/topic/213155-turbo-question/#findComment-3767492
Share on other sites

Bullet - I've got 740cc's goin in, stock block + GTRS, mods as in sig. Was told it'll be fine by my mechanic. Is it just 'fiddly' to do or something?

It really depends on your overall set up and the power that you are looking to get out of it as to which injector size is well suited.

Bigger is not necessarily better when it comes to injectors, I originally put 650cc squirters in mine and because I was building a set up more for response and track work rather than outright power or drag racing they were far to big.

When the tune was being done with the 650's my tuner had to pull out over 50% of the fuel going in to keep the AFR's right and that made it run like crap because the injector duty was to low, it also refused to idle.

So 550cc's went in and they were as big as I needed for my set up.

If youre looking for about 300kw at the wheels, which isnt a huge ask with the turbo you have then you will probably need bigger than 550's in yours, you will probably need a rising rate fuel reg to keep as much pressure in the rail as possible to.

I dont claim to be a tuning expert, but I have done just about every bolt on mod that you can do to an RB motor aswell as a lot of time on the dyno having it tuned, Im only speaking from my own experience. :thumbsup:

Link to comment
https://www.sau.com.au/forums/topic/213155-turbo-question/#findComment-3768813
Share on other sites

17psi on a stock tune could make mince meat of a piston in no time... If you dont have the correct AFR (air fuel ratio) you run a high risk of detonation due to lean fuel and air mixtures.

But you might be lucky, I have heard of people doing it and not having troubles...

However, my advice is to run a maximum of 12 - 14psi with a stock R33 RB25DET computer, if you start running anything over this kind of boost you may have serious issues with your AFR's being far to lean and if you get even a small boost spike without safe mixtures you could easily end up with a piston head with a large chunk missing.

Do it once, do it right...

1st step - Fuel pump (Bosch 040 or Walbro are the most popular)

2nd step - Splitfires (or higher amperage coils) the standard coils dont have high enough amps and with more boost you could end up blowing out the spark at high RPM.

3rd step - Computer and injectors (try not to go over 550cc on a stock motor as they can be a bitch to tune if they're to big) and something like a Power FC plug in or a Microtech would be needed to control the whole kit.

Oh and make sure that you have some sort of reliable boost control and a front mount + big exhaust or you'll just choke a bigger turbo and it wont breathe enough for decent power gains.

Ive been through all of this and unless you know what your doing and can do most of it yourself it can become very expensive.

Happy shopping :)

+ 1 on everything said here, apart from id go 740 injectors because your buying them, you may as well go that big. mean while this is doing everything right, you could get away with doing less then half the stuff, but its all risk management!

take it easy, stuart

Link to comment
https://www.sau.com.au/forums/topic/213155-turbo-question/#findComment-3769082
Share on other sites

Hmm I've got a Nismo pump instead of the rising rate fuel reg. I'm looking for 260-270, I don't like fireworks (stock bottom end!). So from what you said, I guess yeah I'm better off with my 740cc's. Will find out earyl next week anyway when John's done!

Link to comment
https://www.sau.com.au/forums/topic/213155-turbo-question/#findComment-3769381
Share on other sites

555 nismo injectors, 70% duty cycle, std internals except tomei sticks, 290+rwkw

I have a SARD fpr, so may help a bit?

I reckon 550's would be fine myself, but its your $$$$ and 555's cost nearly as much as 740's

Link to comment
https://www.sau.com.au/forums/topic/213155-turbo-question/#findComment-3773267
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • For these last 7 years of ownership, I've always had to use a small scissor jack under one of the front tow hooks to raise the front just enough so my low-profile jack fits under to reach my subframe jack point. I'm beginning to get annoyed of always having to do this. Are there any lower low-profile jacks that fit under the gtr lip on a dropped car?
    • Seat of the pants assessment of the new intake: The car is way less "doughy" when hitting the loud pedal, especially off idle when stopped or in traffic, I did use a cheapo lazer thermal thingo to measure the temp around where the pod filter got its air, it was between 55 - 60°C, in saying this the car was shut off and not moving, so the OEM intake pipe was not supplying any fresh air to where the pod was when the car was at least moving A weird bonus was induction noise on the throttle in the cabin increased a bit,  I was worried that I was actually going to lose some of that induction noise I love so much, outside though, when I got the daughter to do a WOT drive by pass for me, the induction noise has increased alot when on the throttle, not quite ITB doort, but well up there I'm extremely happy with the results and have been exploring the country roads in the region  As for house mods: 1.New front fence is up and is awesome, it really upgraded how the joint looks from the street, and the added security is nice 2. Electricians have replace some interior lights, and with more lighting in the garage, a few new motion detecting lights out the front above the garage, front room, and at the front door, which I have already found heaps helpful coming and going, also now has fancy pants CCTV all round the house The only hold point for power though is the solar and batteries due to supply issues, although this will happen over the next few weeks 3. I have done a heap of landscaping out the front and I'm almost ready to do a new small retaining wall with some nice blocks to replace the brick and cemented in rocks around the raised garden beds cemented in river stone "was the fashion at the time" the house was built. I currently have a pallet of retaining wall blocks and 2 bulka bags of 20mm blue metal to replace the wood chip that is in the raised garden beds around the house 4. I now have 3 big raised garden beds for out the back to grow some vegetables, about 70cm high, 200cm long and 100cm wide 5. My 2 compost bins are already pretty full with brown, green and kitchen waste from the landscaping I'vedone so far, but they will probably take a few months to break down, so anything else that gets chopped, trimmed, and kitchen waste will just start filling the base of the raised garden beds to about 30cm before I start throwing 40cm of good compost, and stuff, for the vegetables to grow in, I'll need a few ton of compost and soil, but the local supplier can sent me bulka bags of the stuff Basically the logs, wood chips and a few strategically placed rocks for drainage, will give the beds some good organic materials down low to break down over time, and they will hold moisture during the warmer months to save the water in my big arse water tank if we don't get alot of rain So, all in all, the car and house mods are going well, and I'm really enjoying being retired, I sleep in too 0700 and slowly plod around inside until I feel like actually doing anything, and only work in the yard for as long as want, which has actually been alot over the last few weeks,  although when you look at it, it seems that not a huge amount of work has been done,  until I look at the before I started the work pics Happy days and good times indeed 
    • hahaha yeah. Plan is to get side skirts and probably just rear pods. But going to do them one-by-one. I've got a set that I really like from RHDJapen, but that one isn't shipped to AU. So need to find someone who can get it for me
    • Here's an idea, answer the questions I asked you as they are trying to work out WHY the LSD will be binding up in a straight line.
×
×
  • Create New...