Jump to content
SAU Community

Recommended Posts

Hi guys,

I'm writing a bit to give people a heads up on a noise reducing device I recently installed on my R32 GTR.

Its called a butterfly valve! My mate brought it in a 3 inch size from Autobahn (I hate that f**king store so much) for around $200 and never fitted it too his car, so I bolted it into mine. It is a circular plate which can rotate to restrict airflow in the exhaust system, I found a photo of one for sale on here, and have added a link too it below but a lot of exhaust stores can get them in, but 3" is the largest size i think.

http://www.skylinesaustralia.com/forums/Wo...alve++butterfly

Anyway this is his pink fluffy velvet background picture, from his add but you can see the butterfly, the section of exhaust you bolt into your exhaust and the cable and lever to control it all.

post-20826-1207711251_thumb.jpg

I have a 4 inch exhaust after the gutted cat (it came that way) and I simply put the valve in line with the cat just after it then ran the cable up through the gearstick boot, but you could use the eyelet for the CAT exhaust sensor, then put the control lever on the right kick panel on the drivers side, just under the bonnet release, this keeps it out of view of the police if I get pulled over as they apparently can ask you to open it up for noise testing.

The valve when fully shut its diameter is slightly smaller than the pipe it sits inside so it doesn't completely restrict the airflow but does create a lot of back pressure. Now at idle you wont notice this much, ever revving the engine stationary wont make a huge difference, but under load when most open exhausts are noisiest it really does make it a lot quieter, great if you want to pass a cop in a 50 zone on the side of the road, or you live at the top of a steep hill.

You have to be quite mindful that with the increased back pressure your turbos will not spool up anywhere as fast or easy, and infact if you try kick the arse on the car when it is shut you could potentially blow a gasket as the pressure finds other ways out of the exhaust system, not a problem for me because I had a not standard cat converter on my car and had to trim the flanges on it to fit the cat with an angle grinder and successfully cut a couple of holes in the cat (yes I'm getting them welded next week).

The added bonus of this seams that the engine seams to be running smoother on long cruises;

I think this is relative to valve overlap which is basically how part way during the combustion cycle the intake and exhaust valve are both open, without back pressure to hold the mixture in the cylinder I seamed to be running a little rich at low to mid RPM when the turbos weren't boost like when I'm driving on the highway, something closing the butterfly once I'm at cruising speed has almost completely fixed!

post-20826-1207711950_thumb.jpg

Anyway I can boast enough about this device and the hassles it has already averted for me and hope this helps some of you guys, if anyone needs some help and you post a question and I dont reply please PM me.

Dave

Edited by Keeper
Link to comment
https://www.sau.com.au/forums/topic/214149-exhaust-butterfly-valve/
Share on other sites

I have an Apexi ECV welded inline with my exhaust, so not the flange style

The difference in noise is heaps, if you pull it up and drive with it on it sounds like a stock car with a standard exhaust

Problem is the power restriction - it restricts the power heaps, I could barely make 5psi with the ECV activated where as when it was open it would make an easy 13psi

The idea of it is to restrict the exhaust making it quieter but its not to be driven hard with it activated, so don't boost it or try and push the car hard as it won't go and could cause damage

I'm sure Apexi advertise that it quietens down to 10db - I think that’s what it says on the box if I remember correctly

these kind of systems are becomign standard on many cars

don't some ferrari's offer it?

i know for the V35 sedan when purchasing the sport exhaust in japan you had the option of this kind of valve..

yeah my old mans XKR supercharged jag has something, keeps it quiet and backpressure when its needed down low

also the DECS is a great system, lot of auto shit, and its electronically controlled

but around $550 USD if you can find them anymore!

I must stress you don't try and boost hard when the valve is shut!!!!

the apexi EVC is exactly the same as the one I installed

thats tough when you get in a sticky situation and need some power to get out of. my mates got the apex silencer thats spring loaded so it opens up quite well when under boost and is very quiet, obviously not as good as free flowing but at least you dont have to remember to open and close all the time.

i was seriously considering these kits when i got my defect but in the end i couldnt justify it though the DECS looks pretty good.

You could always somhow attach it the the throttle, so when you give it full throttle, it automatically opens. If you want a cheaper alternative, or a bigger one, go to a truck wrecker and buy an exhaust brake flapper(actually, these are usually vacuum operated, so you may be able to hook it up to manifold vacuum, give it boost and it will open)

Edited by Adriano

OEM there's dozens that use something similar, Dancing horse, Maserati, Bentley, Jag, Aston Martin and so on. Some, like the 360 though, i think are for sound.. not noise suppression.

I've a mate with one, though theres a 4" "Y" pipe. Closed the zhaust works normally, open and it sounds like an open pipe bridge ported 13B *cough* ... So he has an option of loud (100dB) and even louder...

Most are stepper motor controlled, so you could make it open (any angle) by any system with a spare output, like an aftermarket ECU. Im sure a simple PIC could help those with OEM ECU's.

I figured most people used a Y pipe, and diverted the exhaust gases straight to atmosphere, but it seems not of late. :) The large 3.5" - 4" units from teh US seal COMPLETELY for this reason.

BTW, I would expect the roadside RTA to rape you dry if caught.

I would be VERY cautious of exhaust temps (straight through, non Y style) when cruising on the freeway, as the back pressure plus closed loop lamba correction, would make for some very hot exhaust valves i would have thought...

Juz my thoughts

Edited by GeeTR

They blow shut if used in a single pipe. If used in a Y pipe arrangement they are ok. Have a look at how the OEM gear is used, It's always on a second pipe or a diversion in a muffler, it's never blocking the primary pipe.

godzl1975 has obviously experienced it.

rubbish things. get a decent rear muffler and throw the cannon in the bin. Maintain power while avoiding headaches (both literal and metaphoric).

even the brand new falcon has this system, although it wasnt fitted for noise, it was fitted for emission's so i was told....

regardless if the epa catch's a temporary silencing device, your even more f**ked then if you just went over the normal limit.... trust me its not worth the hassle. just make your car a reasonable noise level.

Why does everyone think the rta would have an issue with it, it can only make the car quieter, and should improve emmissions when its shut, as it would be similar to EGR.

the epa in particular heve an issue with such a devcie, as its a device that can temporarily alter the emissions of the car, be it noise and actual gase's.... any temporary emission control device is illegal, aswell as anything that can alter the emission's other then factory, e.g aftermarket computer,bov etc

Yeah, I've been emailing around and I'm now in contact with AES / Hyperflow (Autospeed did a couple of articles on their system) and they've got a few of these things.

Their top-of-the-line one is fully active with a pressure sensor and a configurable control unit, so it can adjust itself to maintain only a certain amount of backpressure. It'll take inputs from the TPS and an RPM signal wire too, so you can also set it to only open at WOT or a certain RPM. Not cheap, but a pretty funky piece of gear.

I'll probably end up going for the dumbest one, which is just a simple on-off switch that I'll conceal somewhere.

a lot of exhaust stores can get them in, but 3" is the largest size i think.

Hyperflow's comes in 4" bore size, but they recommend going half an inch bigger than the rest of your exhaust to retain flow.

But if it was setup to open and close automatically, then it should be legal?

If its set up so it cannot be controlled by the user and, in its automatic mode passes all noise and emissions regulations for the vehicle, then yes it could conceivably be legal. That's how Ferrari, Aston Martin, Lamborhini, etc get away with theirs.

Edited by scathing

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I got back to Japan in January and was keen to get back on track as quickly as possible. Europe is god-awful for track accessibility (by comparison), so I picked up a first-gen GT86 in December just to have something I could jump into right away. The Skyline came over in a container this time and landed in early January. It was a bit battered after Europe, though—I refused to do anything beyond essential upkeep while it was over there. The clutch master cylinder gave out, and so did the power steering. I didn’t even bother changing the oil; it was the same stuff that went in just before I left Japan the first time. Naughty. Power steering parts would’ve cost double with shipping and taxes, so knowing I’d be heading back to Japan, I just postponed it and powered through the arm workout. It took a solid three months to get the car back on the road. Registration was a nightmare this time around. There were a bunch of BS fees to navigate, and sourcing parts was a headache. I needed stock seats for shaken, mistakenly blew 34k JPY on some ENR34 seats—which, of course, didn’t fit—then ended up having the car’s technical sheet amended to register it as a two-seater with the Brides. Then there’s the GT86. Amazing car. Does everything I want it to do. Parts are cheap, easy to find, and I don’t care what anyone says—it’s super rewarding to drive. I’ve done a few basic mods: diff ratio, coilovers, discs, pads, seat, etc. It already had a new exhaust manifold and the 180kph limiter removed, so I assume it’s running some kind of map. I’ve just been thrashing it at the track non-stop—mostly Fuji Speedway now, since I need something with higher speed after all that autobahn time. The wheels on the R34 always pissed me off—too big, and it was a nightmare getting tires to fit properly under the arches. So I threw in the towel and bought something that fits better. Looks way cleaner too (at least to me)—less hotboy, less attention-seeking. Still an R34, though. Now for future plans. There are a few things still outstanding with the car. First up, the rear subframe needs an overhaul—that’s priority one. Next, I need to figure out an engine rebuild plan. No timeline yet, but I want to keep it economical—not cutting corners, just not throwing tens of thousands at a mechanic I can barely communicate with. And finally, paint. Plus a bit of tidying up here and there.  
    • Nope, needed to clearance under the bar a little with a heat gun, a 1/2" extension as the "clearancer", and big hammer, I was aware of this from the onset, they fit a 2.0 with this intake no problems, but, the 2.5 is around 15mm taller than a 2.0, so "clearancing" was required  It "just" touched when test fitting, now, I have about 10mm of clearance  You cannot see where it was done, and so far, there's no contact when giving it the beans Happy days
    • It's been a while since I've updated this thread. The last year (and some) has been very hectic. In the second-half of 2024 I took the R34 on a trip through Germany, Italy, France and Switzerland - it was f*cking great. I got a little annoyed with the attention the car was getting around Europe and really didn't drive it that much. I could barely work on the car since I was living in an inner-city apartment (with underground parking). During the trip, the car lost power steering in France - split hose - and I ended up driving around 4,000kms with no power steering.  There were a few Nurburgring trips here and there, but in total the R34 amassed just shy of 7,000kms on European roads. Long story short, I broke up with the reason I was transferred to Europe for and requested to be moved back to Japan. The E90, loved it. It was a sunk cost of around EUR 10,000 and I sold it to a friend for EUR 1,500 just to get rid of it quickly. Trust me, moving countries f*cking sucks and I could not be bothered to be as methodical as I was the first time around.
    • I assume clearances were all a-okay?
    • Shock tower brace is in +5Kw....LOL  
×
×
  • Create New...