Jump to content
SAU Community

Recommended Posts

hey guys!

just purchased myself a cooling pro stealth fmic (600x240x60) and have just installed it today after a few hours. the only hacking i needed to do was a little bit of the intrusion bar to hug around the corners of the fmic and the hacking of a support bracket on the bottom pipe (would not give me that little extra room to line it up with the stock piping no matter how hard i huffed and puffed).

my warning is mainly for series 2 owners - the first bend of the top pipe prevents your front bar (that is, if you have stock) to go on properly due to the fog light and the housing on the left side (looking at the front of the car). i thought i could hack the housing on an angle but realised it was also the rear of the fog light that actually hit the bend as well and thus i could not line up the right side (looking at the front of the car) of the bumper. hacking the housing that was built into the bar is one thing, but hacking the actual housing for the fog light is another.

after an hour sitting in my thinking chair, i decided to remove the stock fog lights + indicator assembly and hack off the housing built into the bar itself to allow room for that damn bend! now i had the problem of an ugly space where the fog lights + indicator assembly should be, so what i did was pop down to autobarn and bought myself a grill mesh and then bought gtr look-a-like indicators and fog lights. what i did was fill up that gap for the assembly with the grill and just cut out holes to fit in the new indicator and fog light. i left the bottom half as stock so basically, rather then having the fog light + indicator assembly, i now have a grill with a fog light and indicator - pretty much a 400R front bar imitation.

just a note - most or some other fmic piping actually go UNDER the fog light + indicator assembly. just weird when i encountered this problem. had me scratching my head for hours taking apart random things and putting them back in thinking i alligned something off.

APART from that debacle, no problems thus far. im quite happy with the fmic. its definitely living up to its stealth because the bottom pipe hides directly behind the bottom section of the front bar and the core itself is actually hiding behind my plates. only noticable if you look hard enough. i get no turbo lag since the pipes use the existing stock pipes so you get the shortest cooling route possible. i have installed 3 other types of fmic(s) and after a test drive the boost does take longer to pick up speed. with this setup, it spools maybe a little faster if not the same. bottom end rpms have alot more pick up (a little but noticable).

i can only assume, but this kit was really meant for the series 1 owners since their bar has more room behind it but anyone with an aftermarket front bar should have no problems.

hope this helps some of you s2 owners thinking of getting one of these.

Link to comment
https://www.sau.com.au/forums/topic/214746-cooling-pro-stealth-fmic/
Share on other sites

  • Replies 43
  • Created
  • Last Reply

Top Posters In This Topic

Top Posters In This Topic

Posted Images

Hey , Dude thanks. I was about to buy one! i use to have a BLitz LM and i sold it for 1,000 but now i want it bak! :D i only had it for a week !!!!!!!

also could you please post up pics plz :O

Edited by geraus
Hey , Dude thanks. I was about to buy one! i use to have a BLitz LM and i sold it for 1,000 but now i want it bak! :D i only had it for a week !!!!!!!

also could you please post up pics plz :rofl:

Is it me or does this make no sence? :P Why buy a Blitz to sell and get a Stealth? Unless you were after some $? Hehe.

Im guessing, in this case if your like me and have an S2 with a different OEM bumper (pictured) Then possibly you wont have the same effects? As there looks to be bugger all behind the indicator, heeeeaps of room. Can only buy one and try i guess!

post-38698-1208149376_thumb.jpg

hey guys!

just an update, i ended up cheating after all because i did not like the look of the mesh - too much attention in my opinion as i like to keep my car as stock looking as possible. i ended up fitting in the stock lights with some very minor modifications to the assembly. here is just the one picture of the whole thing and i apologise for the poor quality. if anyone wants to see the actual modifications up close just post here and when i am free i will take pictures so you can see up close what i did. i did not take pictures of the grill because i was not going to keep that look.

post-32455-1208154486_thumb.jpg

as you can see, most of the fmic hides under the front bar which in a way gets less wind but since its winter i do not think its a problem thus far although since the fmic is rather wide it may make up for that loss in height. i will have to wait for summer and see how it handles. other fmic(s) i have installed uses the bottom pipe area for extra height for the core (hence why the bend usually goes under the fog light + indicator assembly).

i thought about it today and looked at black warriors tutorial (which was a big help by the way) and noticed that since his core was actually shorter in width than mine, the bend that gave me trouble actually bends earlier to hug the corner straight under the head light. the cooling pro actually bends later or else the piping diameter is comprimised! just thought some people would appreciate an answer to why as i hate not knowing why haha.

Nice paint job on your bar.

was this aimed at me? and are you refering to the sun reflection? as my front bar is in great factory condition.

Edited by Silver_R34_GT-T

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • I wasn’t able to replicate the sound anymore. It was a one time sound so maybe it was just coincidence but it was like small pebbles being dropped in a coke can.   should I try cleaning the MAF? It could be it’s functioning but dirty? I don’t know.
    • Update 4: Hi all. The car drives again! Haven't driven for long, only to store it in the garage again, but the test drive was successful. The coolant and oil leaks seem to be fixed for now. Temps on the engine were also very good, while moving I never even saw 80C water during the approx. 30 minute drive. Ate up all the coolant in the reservoir though so will have to fill that even more when I go to the car next time. One thing that pisses me off is that the RPM gauge is still f**ked, I even resoldered the board twice and used copper paste on the silly screws that are used as connections. Next time I take it out I'll take apart the board and fit new components, I'll see if I can get a replacement IC for it.  I have an appointment set for 22nd of September for the engine tune to 370hp. Alignment also still needs to be done. My hope is that I can get all the legal stuff over with by the end of this season. Anyone of you have advice regarding intercoolers? Currently there is an APEXI core fitted, one of those weird hybrid ones, 600x270x76. I don't think it's bad but it's not new and now I still have the chance to change it now to legally include it in the paperwork. Only issue is that the only options that would arrive in time are a HKS Type R intercooler or generic Ebay spec intercoolers comparable to a JustJap one. Ideally I'd order a Plazmaman but it takes over a month to receive which would mean making the car legal has to wait until next season. Would love to hear some input on this. Same story for my injectors, the previous owner was a nunce and put ID 1050x on the engine. They work but are obviously not ideal at "normal" power levels. But I don't see a reason to change them unless the tuner says it's necessary. I read online before buying a different exhaust that the top secret style rear diffusers won't fit due to the size of the rear resonators. My buddy and I made it work by slightly "adjusting the shape" of the mounting bracket and making some spacers out of 3d print for the mounting bolts. Fits like a charm. Just putting this here in case someone has this problem. Even the hefty HKS Silent Hi Power rear can fits without hitting anything.
    • Well they got my money but they are not getting my gearbox ! 
    • It's needed for rolling idle up, and I think it is a decider on VCT also.
    • I mean, not really. Link ECU's can absolutely still have errors from the ECU thinking it's getting a sensor it's not expecting. I would imagine the speed at the ECU level in Nistune does absolutely nothing anyway? I assume the ECU does not do any fancy TC stuff with regards to front+rear wheel speed or anything of that like anyway. Someone who uses Nistune may be more fluent in it. 
×
×
  • Create New...