Jump to content
SAU Community

No Mufflers, Just 3" Pipe From Turbo To Twin 2.5"s

Proximity Motorsport
 Share

Recommended Posts

Proximity Motorsport Experienced

Proximity Motorsport

Posted
Posted

hey,

Was thinking about cutting off cannon and putting on twin 2.5" pipes out back of r32. (this is not for road use)

Atm car has no mufflers apart from a cannon, and its just 3" turboback. Has anyone ever heard a rb20 with no mufflers. I know if you just unbolt cannon sounds like a sack of shit.. will it sound any better with the extra lengh in pipe?? Has anyone got a clip? I searched youtube but no luck

cheers

Nismo_Boy Grand Master

Nismo_Boy

Posted
Posted
hey,

Was thinking about cutting off cannon and putting on twin 2.5" pipes out back of r32. (this is not for road use)

Atm car has no mufflers apart from a cannon, and its just 3" turboback. Has anyone ever heard a rb20 with no mufflers. I know if you just unbolt cannon sounds like a sack of shit.. will it sound any better with the extra lengh in pipe?? Has anyone got a clip? I searched youtube but no luck

cheers

Search 240sx, rb20, and straight pipe. There are a few sound files of rb’s with open pipes on you tube.

It’ll sound a little “cleaner” with pipes out the back as the sound wont be echoing under the car. It’ll still sound like an Isuzu truck at idle though.

One of my R32’s had a 3inch system turbo to tip with no mufflers or cat, it will get annoying if you daily drive the car and obviously the Police will pick on you.

Would I do it again? Yes. Did it make any power gains? No. The popping on de-cel and the ridiculous amount of flames were a novelty at the time.

Ionos Community Regular

Ionos

Posted
Posted

It will be freaking loud and probably drone. My RB25DET had this exact setup when I bought it, it was horrible. The droning was crazy, sounded great on WOT but how often are you on WOT compared to cruising? Never mind also that it's obviously illegally loud, and the last thing we need with these cars are more attention from the boys in blue.

Chris_A31 Enthusiast

Chris_A31

Posted
Posted

My cefiro rb20 is 2.5" dump into 3" dump back.. only 1 centre res and thats it. I love the sound of it.. no drone at all. Its actually fairly quiet on idle but absolutely screams on boost. I do rate the cefiro rb20 note quite a bit better than the 32 rb20, mainly due to the rougher sound. I dont have any videos of it at the moment though..

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Kapr
      What brakes on R34 GTT(Europe)

      By Kapr · Posted

      Ok i will get those 310mm. I found one but on a different site. This is the description on those...is it ok? Technical parameters: - Axle: front. - Disc type: ventilated. - Number of holes: 5. - Disc diameter: 310mm. - Total height with center: 54mm. - Thickness (new/min.): 30/28mm. - Designed for brake calipers manufacturer: Sumitomo.
    • GTSBoy
      Mistakes were made, my R34 Story

      By GTSBoy · Posted

      You Gregged a whole racetrack!?
    • GTSBoy
      R32 GT-R: 4WD Light Turns On After Bumps – Code 19 (ETS Motor) But No Issues Found

      By GTSBoy · Posted

      Look for broken wire or bad connector at the motor. Might not be it, but is worth starting there, as it is easy.
    • Bireley_32
      R32 GT-R: 4WD Light Turns On After Bumps – Code 19 (ETS Motor) But No Issues Found

      By Bireley_32 · Posted

      Hi everyone, I’m having an issue with my R32 GT-R. Sometimes, when the car goes over a bump or experiences some vibration, the 4WD warning light comes on the dashboard. When I check the code from the control unit in the trunk, it shows Code 19 – ETS Motor. However, everything seems to be working fine — if I turn off the engine and restart the car, the light goes away and everything functions normally. Has anyone experienced this before? Where should I start troubleshooting this issue? Thanks in advance!
    • Kinkstaah
      Mistakes were made, my R34 Story

      By Kinkstaah · Posted

      I'm back from the dyno - again! I went looking for someone who knew LS's and had a roller dyno, to see how it shaped up compared to everything else and confirm the powerband really is peaking where Mr Mamo says it should. TLDR: The dyno result I got this time definitely had the shape of how it feels on the road and finally 'makes sense'. Also we had a bit more time to play with timing on the dyno, it turns out the common practice in LS is to lower the timing around peak torque and restore it to max after. So given a car was on the dyno and mostly dialled in already, it was time for tweaking. Luis at APS is definitely knowledgable when it came to this and had overlays ready to go and was happy to share. If you map out your cylinder airmass you start seeing graphs that look a LOT like the engine's torque curve. The good thing also is if you map out your timing curve when you're avoiding knock... this curve very much looks like the inverse of the airmass curve. The result? Well it's another 10.7kw/14hp kw from where I drove it in at. Pretty much everywhere, too. As to how much this car actually makes in Hub Dyno numbers, American Dyno numbers, or Mainline dyno numbers, I say I don't know and it's gone up ~25kw since I started tinkering lol. It IS interesting how the shorter ratio gears I have aren't scaled right on this dyno - 6840RPM is 199KMH, not 175KMH. I have also seen other printouts here with cars with less mods at much higher "kmh" for their RPM due Commodores having 3.45's or longer (!) rear diff ratios maxing out 4th gear which is the 1:1 gear on the T56. Does this matter? No, not really. The real answer is go to the strip and see what it traps, but: I guess I should have gone last Sunday...
×
×
  • Create New...