Jump to content
SAU Community

Recommended Posts

hey guys, im thinking of lowering my car, i love how the stock suspension rides and launches though which is the only thing holding me back however i think my car will look a lot better lower, want it as legally low as possible, do i just get springs ? whats the go ? not sure ho3w suspension works when upgrading, i know springs lower the car and shocks hold the car thats been lowered form bottoming out ? is that true i dunno hehe

cheers

Link to comment
https://www.sau.com.au/forums/topic/21754-suspension-what-to-go-for-if-i-do-it/
Share on other sites

  • Replies 53
  • Created
  • Last Reply

Top Posters In This Topic

Go for a quality set of shocks like Bilstein or Koni, and some nice lowered springs like king springs or Whiteline and it will ride nice and handle well. Should set you back $1200-$1300ish. Not sure how low you can go, I would probably settle for 30mm lower. Check the Whiteline site for different options and prices.

thanks, yer koni quoted me $1800 for their stuff but someone told me its around $1300 fitted soi im confused now, i am willing to spend around $1300 but yer anymore i dont see it being worth it till the caqrs paid off... that was directy from koni and from a place near my house that quoted 1800... hmm

Never priced koni s, but you can get the Bilsteins for under a grand front and rear which leaves the springs which are about 300 ish. The Koni shocks do have the advantage of being adjustable if you are that way inclined. You could buy a spring compresser from Repco for $45 and do it yourself. Then you only have to pay for the wheel alignment afterwards. Its pretty easy, just a little time consuming which is why labour costs can be a little rich.

what suspension whiteline uses? I read an hpi old article, they use bilstein for their handling kit, is that correct?

how does bilstein ride on bumpy road? dun want my daily driver to be so stiff on my back...

Whiteline use Bilstein Shocks in there kits and they charge $1350 delivered, not bad.

I have only heard good things about them I'm looking at getting the sports pack from Whiteline in the next couple of weeks.

DIY nath.. you have plenty of time now :P

Just make sure you also replace the shocks with the springs. Some people just replace the springs to save a few $, which effectively reduces the life of the shocks, and overall efficiency of the whole setup

I got Whiteline springs with Bilstein shocks (both from Whiteline) but for some reason the front springs are 10mm lower than the back. I don't know if this was deliberate or not but it looks pretty good this way so I'm not complaining.

You don't need a spring compressor at all to fit this suspension. I just used my own body weight to compress the spring about 2cm.

Have you guys ever thought about upgrading your swaybars asw ell?? As a bang for you buck, these alone will make your car handle better then just lowered springs and shocks. Some of you will bw saying like WTF? It's true as whiteline have done heaps of R&D on these. Springs and shocks are good but really need to work as a package with your swaybars aswell as these decrease your body roll and make the car sit flatter around the corner. DJ_L3thal, if your happy with how your car launches and all, consider doing the swaybars first or all at the same time.

I can back up what Honey has said - I did the swaybars on my Commodore and it made it handle like a Skyline :) (well, almost!)

I would have gotten swaybars for my Skyline before the shocks and springs, but the old suspension was totally buggered so I didn't have much choice with limited funds. The other thing too is that the stock Skyline swaybars are much better than factory Commodore ones, so there's probably more room for improvement on the latter.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • From there, it is really just test and assemble. Plug the adapter cables from the unit into the back of the screen, then the other side to the car harness. Don't forget all the other plugs too! Run the cables behind the unit and screw it back into place (4 screws) and you should now have 3 cables to run from the top screen to the android unit. I ran them along the DS of the other AV units in the gap between their backets and the console, and used some corrugated tubing on the sharp edges of the bracket so the wires were safe. Plug the centre console and lower screen in temporarily and turn the car to ACC, the AV should fire up as normal. Hold the back button for 3 sec and Android should appear on the top screen. You need to set the input to Aux for audio (more on that later). I put the unit under the AC duct in the centre console, with the wifi antenna on top of the AC duct near the shifter, the bluetooth antenna on the AC duct under the centre console The GPS unit on top of the DS to AC duct; they all seem to work OK there are are out of the way. Neat cable routing is a pain. For the drive recorder I mounted it near the rear view mirror and run the cable in the headlining, across the a pillar and then down the inside of the a pillar seal to the DS lower dash. From there it goes across and to one USB input for the unit. The second USB input is attached to the ECUtec OBD dongle and the 3rd goes to the USB bulkhead connected I added in the centre console. This is how the centre console looks "tidied" up Note I didn't install the provided speaker, didn't use the 2.5mm IPod in line or the piggyback loom for the Ipod or change any DIP switches; they seem to only be required if you need to use the Ipod input rather than the AUX input. That's it, install done, I'll follow up with a separate post on how the unit works, but in summary it retains all factory functions and inputs (so I still use my phone to the car for calls), reverse still works like factory etc.
    • Place the new daughterboard in the case and mount it using the 3 small black rivets provided, and reconnect the 3 factory ribbon cables to the new board Then, use the 3 piggyback cables from the daughterboard into the factory board on top (there are stand offs in the case to keep them apart. and remember to reconnect the antenna and rear cover fan wires. 1 screw to hold the motherboard in place. Before closing the case, make a hole in the sticker covering a hole in the case and run the cable for the android unit into the plug there. The video forgot this step, so did I, so will you probably. Then redo the 4 screws on back, 2 each top and bottom, 3 each side and put the 2 brackets back on.....all ready to go and not that tricky really.      
    • Onto the android unit. You need to remove the top screen because there is a daughterboard to put inside the case. Each side vent pops out from clips; start at the bottom and carefully remove upwards (use a trim remover tool to avoid breaking anything). Then the lower screen and controls come out, 4 screws, a couple of clips (including 3 flimsy ones at the top) and 3 plugs on the rear. Then the upper screen, 4 screws and a bunch of plugs and she is out. From there, remove the mounting brackets (2 screws each), 4 screws on the rear, 2 screws top and bottom and 3 screws holding in the small plates on each side. When you remove the back cover (tight fit), watch out for the power cable for the fan, I removed it so I could put the back aside. The mainboard is held in by 1 screw in the middle, 1 aerial at the top and 3 ribbon cables. If you've ever done any laptop stuff the ribbon cables are OK to work with, just pop up the retainer and they slide out. If you are not familiar just grab a 12 year old from an iphone factory, they will know how it works The case should now look like this:
    • Switching the console was tricky. First there were 6 screws to remove, and also the little adapter loom and its screws had to come out. Also don't forget to remove the 2 screws holding the central locking receiver. Then there are 4 clips on either side....these were very tight in this case and needed careful persuading with a long flat screw driver....some force required but not enough to break them...this was probably the fiddliest part of the whole job. In my case I needed both the wiring loom and the central locking receiver module to swap across to the new one. That was it for the console, so "assembly is the reverse of disassembly"
    • But first....while I was there, I also swapped across the centre console box for the other style where the AV inputs don't intrude into the (very limited !) space.  Part# was 96926-4GA0A, 284H3-4GA0B, 284H3-4GA0A. (I've already swapped the top 12v socket for a USB bulkhead in this pic, it fit the hole without modification:) Comparison of the 2: Basically to do the console you need to remove the DS and PS side console trim (they slide up and back, held in by clips only) Then remove the back half of the console top trim with the cupholders, pops up, all clips again but be careful at the front as it is pretty flimsy. Then slide the shifter boot down, remove the spring clip, loose it forever somewhere in the car the pull the shift knob off. Remove the tiny plastic piece on DS near "P" and use something thin and long (most screwdrivers won't fit) to push down the interlock and put the shifter down in D for space. There is one screw at the front, then the shifter surround and ashtray lift up. There are 3 or 4 plugs underneath and it is off. Next is the rear cover of the centre console; you need to open the console lid, pop off the trim covering the lid hinge and undo the 2rd screw from the driver's side (the rest all need to come out later so you can do them all now and remove the lid) Then the rear cover unclips (6 clips), start at the top with a trim tool pulling backwards. Once it is off there are 2 screws facing rearwards to remove (need a short phillips for these) and you are done with the rear of the console. There are 4 plugs at the A/V box to unclip Then there are 2 screws at the front of the console, and 2 clips (pull up and back) and the console will come out.
×
×
  • Create New...