Jump to content
SAU Community

Just Fitted Dump\front Pipe


Recommended Posts

Hey all I just put a new front\dump on my r33 and when i put her back on the ground the engine aint turning over.

When i turn the key i can hear what i beleive to be the starter motor goin click click click (really fast) Now she has never had any problem starting so has shown no signs of a weak starter...

The dump pipe install took me say 3-4 hours in which time the radio was on.. could it be not enough power in the battery to engage the starter motor properally? I would have thought that if there was not enough juice it would just crank to motor real lazy or something.?

Its got me f&*'d cause all i touched was the dump pipe...

Any ideas?

Link to comment
Share on other sites

could just be your battery terminals, take of the terminals just get a steel brush and run it over the neg and pos terminals on the battery to clean them. then put them back on, tighten them, make sure there is no movement and try start it, sounds as if its not making contact properly. if it was flat it would click slowly.

if you decide to go through the hassle of removing the battery from the boot...

it might pay to check that there is enough water inside to cover the electrodes by taking the caps of and shinning a torch down there. if they need topping up, go and buy some distilled water because normal water will stuff it.

cheers 4drftn

Link to comment
Share on other sites

^ maybe your just getting too smart Mafia lol

lol, when you turn the key, and the car goes "tick tick tick" how much more obvious can you get?

lol, would you go and get some jumper leads, or runn off to SAU and post a thread?

Link to comment
Share on other sites

lol, when you turn the key, and the car goes "tick tick tick" how much more obvious can you get?

lol, would you go and get some jumper leads, or runn off to SAU and post a thread?

I'm hearing ya... common sense, It's an oxymoron I say!

Now if you can just tell me where I can purchase some wiper blades for my 1997 stagea...thx :domokun:

Edited by madbung
Link to comment
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share



  • Similar Content

  • Latest Posts

    • Updating results.  Using ATR45SS-0 model VS UHF57-900. Those two are very different turbos, different wheels sets with different wheel hub profiles but yet with almost identical result. I’m intrigued with both turbos performance. ATR45SS-0 was a 61mm turbo first developed in May 2020, UHF57-900 was a 62mm turbo developed in March 2024 as a powered up alternative of a G30-900. On paper ATR45SS-0 maxed at 563rwkws, while UHF57-900 maxed at 568rwkws. ATR45SS was slightly more responsive with slightly better power band through the mid range.  Road driving ability, ATR45SS-0 had better throttle response, felt more robust under throttle, as it wakes up earlier. I think G series wheel hub design made it to have higher inertia under light throttle. Doing bit more prototype work in the next few weeks, will update result when its back on dyno again. ATR45SS0 Blue, UHF57-900 Red Chequered tuner's Dynapack hub dyno, E85 fuel. Mod list is in video below video_20240604_114214.mp4    
    • Did you run the power cables for the mac valve to the other side of the car near the fusebox? Utilizing the stock boost controller cables? or did you run new ones?
    • Hey I have a potentially stupid HICAS question 🤣 I'm currently doing a full hicas delete, Power steering pump modified to non hicas, all lines removed from the car along with all electronics. My stupid question is - Do I need a lock out bar? is there any reason why I cant just remove everything from the rear end? I already have a lock out bar but thinking to save a few extra grams I could also get rid of the arms and tie rods as well and just run it with nothing in its place? or would it have a negative effect on handling?
    • Hi how are you guys?  I know i have been absent for years but im coming back slowly guys just wondering if anyone know where the ball joint on the NISMO arm front and rear can be replaced with OE parts?  Also  i know this is not the thread looking for springs and blistein shocks for the 260rs. Please advcie     cheers    yudy
    • Hi i do you have for stages 260rs?
×
×
  • Create New...