Jump to content
SAU Community

Recommended Posts

Item: r33 series 1 afm

Age: from a 94 gtst that's done 107k

Condition: good

Price: $90 delivered

To Fit: (What car) as above

Location: tuggerah (central coast, NSW)

Contact: post or PM

Comments: upgraded to z32afm

Item: r33 series 1 ecu

Age: from a 94 gtst that's done 107k

Condition: good

Price: $100 delivered

To Fit: as above

Location: tuggerah (central coast, NSW)

Contact: post or PM

Comments: using a haltech instead

Item: r33 series 1 turbo elbow

Age: from a 94 gtst that's done 107k

Condition: good

Price: $60 delivered

To Fit: as above

Location: tuggerah (central coast, NSW)

Contact: post or PM

CIMG1141.jpg

everything else eg. hoses, clamps, piping etc can be picked up for $50

CIMG1116.jpg

CIMG1140.jpg

prices aren't negotiable

  • 2 weeks later...
  • 3 weeks later...

while i get the reason behind it....not being able to edit the original for sale post if really annoying :)

a little bit negotiable on above prices now

just realised the turbo elbo is missing 1 of the 3 screws

the afm is actually a z32 that i purchased from 'doodz' brand new who bought it from just jap, comes with plug, not an rb25det s1 afm as suggested above (got my sticker labels mixed up) :P . it's still unused

numbers on orange sticker reads 22680 30POO A36-000 N62. 1916F

asking $220 not negotiable

also have a pair of 235/45/17 kumho 711's for sale, will check how much tread there is later in the week. only asking $50

I may also have an rb25det power fc + hand controller for sale soon, but need to double check it works.....stay tuned

  • 2 weeks later...
Guest
This topic is now closed to further replies.


  • Similar Content

  • Latest Posts

    • The cross sectional area of a circular hole scales with the square of diameter. So a 2mm diameter hole is 4x the area of a 1mm hole. Not double. The 1.7mm hole is nearly 3x the area of a 1mm hole. You do not need restrictors at both ends of the oil supply line. If you have new, additional restrictors at the turbo end, that you did not have before, then you do not need a restrictor at the inlet end.
    • Hi all. Been a while but things are moving along. I just have something that I am wondering about. Since I will use OEM turbo oil pumbing, I got myself a new bolt, the one that goes into the engine block oil feed. As I recall (and see visually) this bolt comes restricted with I think a 1.7mm hole? Not quite sure but it was something around that size. The turbos have 1mm restrictor bolts installed, as necessary due to ball bearings and my higher oil pressures. Can I now just use that OEM bolt with the 1.7mm hole in for the engine block or will this actually be too much oil flow restriction and I have to drill it out first? In my head it would make sense for the bolt to be at least 2mm wide as both turbos take "1mm of oil flow". Do let me know if my logic is flawed here, I just want to make sure I don't kill my turbo bearings with too little oil. Don't know if I can trust the saying I read somewhere that ball bearing turbos essentially only need an oil mist
    • There are several aftermarket options available, from not-too-painful moneyhttps://justjap.com/collections/driveshafts-bearings/products/d-max-reinforced-replacement-rear-driveshaft-set-fits-nissan-s13-s14-s15-r32-r33-r34-c35 and  https://justjap.com/products/crank-motorsport-billet-rear-axles-fits-nissan-skyline-r33-gts-t-r34-gt-t?srsltid=AfmBOorQk4xkGUa98kO7v2ePLUiNt-HRrM2AwWNw9mbSIVE1ujBVwY__, all the way up to The Driveshaft Shop https://driveshaftshop.com/skyline-cv-axles/
    • Yeah based on old XRC5964S specs, it looks to be roughly GTX3576R sized? But this 5964S compressor will flow 90lb airflow somewhat similar to the compressors in both the GTX3584RS or G35-1050.. I fully expected the 0.64 rear A/R to choke up top - seems way too small from typical convention - but these are seemingly beneficial over the prior 0.82 results.. Be interesting to see if he comments on the EFR question in that thread - he mentioned in a prior video that BW EFR's were the "cats pajamas 10 years ago", but by the sounds of things all his kits have been using Xona for quite a while now.
    • Yeah it’s still got the oem manual gearbox and clutch, only kinda mods are a blow off valve, coil overs, and a aftermarket intercooler. Also had it for about 2 months now with a lovely midnight purple paint on it.
×
×
  • Create New...