Jump to content
SAU Community

Recommended Posts

Guys - as always, I enjoy the banter so.....

I am building a RB26 with the usuals:

Wiseco Forged pistons

Eagle Rods

R33 Crank

Tomei Head Gasket

N1 water pump

N1 oil pump

ACL Bearings

Stock Reco Head

Adjustable cam gears

Standard 05U Block (to be bored to first O/S / 86.5)

Turbos - still deciding -5's or -7's (or equivelent)

(would love a set of AX53B70's - anybody got some?)

Blah blah etc.

Will have the fuel and ecu to support plenty of power.

Anyway... question is:

At what point (power lever, type of usage etc) should I be considering a N1 block?

Your opinion matters ;)

What do you guys think?

Edited by Antimatter
Link to comment
https://www.sau.com.au/forums/topic/219038-at-what-point-do-i-need-an-n1-block/
Share on other sites

Not at those power levels ;)

Well above 400, 450 even

the fastest drag skyline in this country makes over 1200hp

our car is producing over 900hp

both run STD 05U Nissan blocks

N1's have a lot of wank factor in my opinion.

So I can make a 400kw on a standard block? is there any "special" prep for that sort of power? I.e that grouting / cement I hear about.

you can "hardbloc" it as i have done to a few...

but a correctly set-up engine that is properly balanced will go a long way to saving your block.

apoligies for the double post...

Hi Ash ;)

Edited by DiRTgarage
i personally would pick a tomei or JUN oil pump over a N1 oil pump

ur rebuilding the engine so u may as well spend abit more and get some thing stronger

N1 oil pumps are just fine on a street engine as long as 8000rpm is not exceeded too often and a decent balancer is used.

Well my car (who was owned by Mik before me) cracked his stock block at 370 KW at the rears with a Tomei stroker. However this was a Series 3 R33 and from what i can gather these blocks were quite porous

N1 oil pumps are just fine on a street engine as long as 8000rpm is not exceeded too often and a decent balancer is used.

i know a few people who have been threw more then 1 or 2 N1 oil pumps B4 going tomei oil pump

these are street cars that dont see over 8000rpm

i know a few people who have been threw more then 1 or 2 N1 oil pumps B4 going tomei oil pump

these are street cars that dont see over 8000rpm

and probably were wearing 13-15 year old rubber balancers on them that were doing little more than helping the belts go round on the front of the engine.

So many engines rebuilt with dodgy balancers slapped back on them without a thought.

I raced for over 3 years with an N1 at over 8500rpm not a problem. Engine was built by me and properly balanced with a new harmonic balancer fitted.

They are not indestructable but if engine is properly built and ran correctly they survive fine in a street application.

Yes the Tomei pumps are good...out of the aftermarket the Tomei and JUN are definately the pick of them.

Edited by DiRTgarage

OK... so I am getting some thumbs down on my oil pump... ANYWAY

Looks like my block will put up with me screwing the guts out of a pair of -5's?

i wouldnt risk using a N1 oil pump, spend the extra on sumthin better for sure.
i wouldnt risk using a N1 oil pump, spend the extra on sumthin better for sure.

How many R34 N1 engines fracture oil pumps?...none that ive heard of...why not?

well balanced engine with good quality fresh balancer on the front.

its harmonic crank vibration that kills oil pumps...the higher the revs the worse the problem.

id spend the extra $600 on an ATI balancer and stick with your N1.

this is free advice from someone who has done a lot of work, testing and research on this very issue. At quite a bit of expense.

Edited by DiRTgarage
How many R34 N1 engines fracture oil pumps?...none that ive heard of...why not?

well balanced engine with good quality fresh balancer on the front.

its harmonic crank vibration that kills oil pumps...the higher the revs the worse the problem.

id spend the extra $600 on an ATI balancer and stick with your N1.

this is free advice from someone who has done a lot of work, testing and research on this very issue. At quite a bit of expense.

Am i buying an ATI balancer now Paul? lol

Maybe I will start a thread on oil pumps :(

Anyway - to look at my original question about the blocks.... what is it that hurts them?

I have a block that came out a car that would have not been making much more than 300kw. Block cracked between the waterjacket and the bore number 2, filled the bore with water (at revs), and ended with a piston sized hole in the side of the block....

It was a stock motor that was obviously leant on. What a way to go though... BOOM!

:P

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • (Rb25det intake manifold) I’m having a hell of a time trying to find the full part or part number of this coolant hardline so far I was given these (Below) but they aren’t what I’m looking for and was told it’s the IAR or aac valve but that doesn’t seem to be it either. If someone could point me in the right direction it’d be greatly appreciated. Or if anyone has it for sale that’d be great too. I have recently purchased a greddy manifold and I can’t seem to find my old one to pull it off.  (Front Heater Return / Water Pipe (under intake): Primary part: 14053‑21U10 (front return pipe assembly for R33/R34 RB25DET) Alternative listing: 14053‑21U00 (same pipe, sometimes interchangeably referenced)   Heater Feed Pipe: Listed as 14075‑04U00 or feed-related variant 14053‑AG500)    
    • This sounds cool. But, as per usual, anything really complicated like that, that I take on, constitutes a steep learning curve that I never actually "learn". I just get it working, install it and start using it. Then, when it breaks a few months later, I've got no memory of what I did, how I did it, or even the bloody IP address I gave it. I'm having more or less exactly that problem right now. My Proxmox machine was discovered to be non-responsive, and the VMs on it were ditto. Power cycle it to a stream of loud Dell beep codes - which was unpopular at midnight, I can tell you. Move it to the lounge room so I can HDMI it to the TV for a screen, see the boot messages complaining about the /PVE/data having all sorts of LVM problems, saying it needs to be fixed manually. And I'm like....great. How am I going to work out what I need to do? At least it wasn't the stupid Silicon Power SSD shat itself. Mental note for all readers - DO NOT BUY SP SSDS! They are shit. I have had one take out an entire VM setup already, and this one could have done the same. Maybe it actually has. Cheap Chinesium shitbaskets. I won't cheap out again, even on play projects with no budget. Because my time budget having to fix shit is worth far more than the cost of proper parts.
    • I do typically agree. These days even the screens most people use have more of a boot time than the main device. However, I've seen an interesting use of the RPi in vehicle, however it involves effectively building your own OS and MBR, as then it boots up exceptionally quickly, as you don't have everything needing to start up, and you can then also run it up as an RTOS, while still having more compute than an Android can give for things like display, and processing. A very huge task that would be though for Duncan, I'm not sure that's his skill set (or Arduino programming and wiring) ha ha. If end goal is definitely just water cooling, Arduino would be the simpler setup especially for a rookie. If he wants extra display stuff though, bashing some code in Python on an RPi may be the better result for both systems.   Unfortunately the new device I'm building at work which runs a display, is too slow of a display for dashboard style purposes. More extreme low power, update only a couple of times a day type system
    • I don't like "actual computers" for in car use. They take time to boot up, have OS annoyances, and so on. Arduinos etc are ready to go a few seconds after power on, don't mind being agressively powere cycled, because everything is non-volatile, don't mind being shaken and stirred.
    • As Fred would tell us, it's all about interpreting the rules. It's not a water sprayer, it's a water mister... But everything else you've said, 100%! Even a raspberry Pi would be great, use HDMI out for a display, and add a raspberry Pi CANBus hat to read values out from the ECU.
×
×
  • Create New...