Jump to content
SAU Community

Recommended Posts

As it says...

Our biggest issue at the moment in getting this club up and running officially is the fact that we have a very diverse range of people wanting membership and wanting to be apart of that glorious thing that is, SAU_VIC.

On one hand we have the people that want CAMS affiliation, track days exclusive to our members.

On the other we have those that just want to be apart of SAU to hang out, enjoy and do things with those that are in this group as we all are a great bunch of people, more of a social skyline enthusiast type role

Now the first option is great and what we all deep down want. Involvement in a club that is able to hold track days and group events exclusive to our club. The only issue with this is that it gets costly.

Just to get the club up and running with CAMS affiliation is going to cost us all. There is also a lot of paper work associated with it and a lot of time needs to be dedicated. We will need a ABN, PO BOX, Public Liability etc etc and this costs money.

Lets say we got this far, we would then need someone/people dedicated to planning and organising events. When i say events im not talking about "yeah we are going to meet up at bell st maccas and cruise down to st kilda", im talking about a proper event, with maps and a purpose.

This type of club will take dedication from people who can dedicate their time and resources into the club. It will also not be a cheap club to join from what we have already researched and as such may not be viable for a lot of people out there. As such i think we need to find some way to have both!

Track days and such for those that want it and just social events for those that dont want to have to pay for the rest of it.

Perhaps we can make a club that has those who want track work etc and on the side with lesser access and so fourth have a "social club" for those that who just want to go on general cruises, meets etc.

I would say that the best way to do this would be to put it to a poll and let u guys decide.

Link to comment
https://www.sau.com.au/forums/topic/22158-your-club-what-do-you-want/
Share on other sites

  • Replies 58
  • Created
  • Last Reply

Top Posters In This Topic

I think the best option for all is the option between Full and Social...

ideal structure would be...

Minimal CAMS affiliation (ie less than 40 members registered for CAMS purposes). Costs $440 p/a

Then you have the social club, charge $20 for membership, gets you a few stickers and a membership card which gets you habib rates at a couple of workshops etc.

Lets say we get about 50 members (not that hard) that's $1000 to start the club. This could give us a good base to work with.

For members wanting track days they'll have to opt for the CAMS affiliation route which could be $20 + cost for cams affiliation divided amonst no of ppl wanting to participate in track days.

Without a track day membership you can't participate in a SAU VIC organised track day, but you are more than welcome to watch.

How's that sound guys?

Last time we had a drive to get SAU into MAS a lil impromptu BBQ raised $240 sumfin, so $20 per person for membership isn't a hard ask.

As for ABN and PO Box I can handle that, I've done it before for my own business, so its not too much of a hassle. Biggest hassle is book keeping and Public Liability.

$20 a person is nothing. I was part of the Volvo club of Victoria (don't laugh) which is a non-cams club and that cost me $50 a year. That included: a monthly meeting (with guest speakers), economy runs (even with other clubs), a discount card, cruises, bbqs and a quarterly magazine. So there were formalities but it was also very sociable. So the option between full and social is a good way to go...

with the full membership u will need to pay 30-50 a year ontop of the $20 (or around there)... which includes cams, track days, official cruises and bbqs and functions etc

Originally posted by inark

with the full membership u will need to pay 30-50 a year ontop of the $20 (or around there)... which includes cams, track days, official cruises and bbqs and functions etc

Inark thats still not very expensive, i think that most people would be willing to pay that. Thats less than a weeks insurance!! (for some) I like the 2 stage membership as well. I think people would pay $30 just for social mem., just to help the club along a bit at the start.

Now all i need is a car, still cant find anyone selling an R32 5speed with sunroof in Vic. :)

:) track days dont matter about what car u got or what mods... its about experiencing things that most ppl dream about... ive always wanted to go out on to a track and see what i can do no matter what car im in... its not a race jayden so if ur car isnt AS fast its no matter :D

no one will laugh... cause thats not the type of ppl that we want in the club.

West... no rollcage will be needed :)

James & Max thats great to hear... also for cams affiliation we will need volunteers of about 10+ppl who will need to be trained by the CAMS guys as field marshalls etc for track days... this means NO track work for these ppl and they will only be doing marshalling so im sure from the guys who arent going to go the full membership we can organise ppl from the club to do stuff like this if they have the time.

will keep u guys updated as we go.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Next on the to-do list was an oil and filter change. Nothing exciting to add here except the oil filter is in a really stupid place (facing the engine mount/subframe/steering rack). GReddy do a relocation kit which puts it towards the gearbox, I would have preferred towards the front but there's obviously a lot more stuff there. Something I'll have to look at for the next service perhaps. First time using Valvoline oil, although I can't see it being any different to most other brands Nice... The oil filter location... At least the subframe wont rust any time soon I picked up a genuine fuel filter, this is part of the fuel pump assembly inside the fuel tank. Access can be found underneath the rear seat, you'll see this triangular cover Remove the 3x plastic 10mm nuts and lift the cover up, pushing the rubber grommet through The yellow fuel line clips push out in opposite directions, remove these completely. The two moulded fuel lines can now pull upwards to disconnect, along with the wire electrical plug. There's 8x 8mm bolts that secure the black retaining ring. The fuel pump assembly is now ready to lift out. Be mindful of the fuel hose on the side, the hose clamp on mine was catching the hose preventing it from lifting up The fuel pump/filter has an upper and lower section held on by 4 pressure clips. These did take a little bit of force, it sounded like the plastic tabs were going to break but they didn't (don't worry!) The lower section helps mount the fuel pump, there's a circular rubber gasket/grommet/seal thing on the bottom where the sock is. Undo the hose clip on the short fuel hose on the side to disconnect it from the 3 way distribution pipe to be able to lift the upper half away. Don't forget to unplug the fuel pump too! There's a few rubber O rings that will need transferring to the new filter housing, I show these in the video at the bottom of this write up. Reassembly is the reverse Here's a photo of the new filter installed, you'll be able to see where the tabs are more clearing against the yellow OEM plastic Once the assembly is re-installed, I turned the engine over a few times to help build up fuel pressure. I did panic when the car stopped turning over but I could hear the fuel pump making a noise. It eventually started and has been fine since. Found my 'lucky' coin underneath the rear seat too The Youtube video can be seen here: https://www.youtube.com/watch?v=uLJ65pmQt44&t=6s
    • It was picked up on the MOT/Inspection that the offside front wheel bearing had excessive play along with the ball joint. It made sense to do both sides so I sourced a pair of spare IS200 hubs to do the swap. Unfortunately I don't have any photos of the strip down but here's a quick run down. On the back of the hub is a large circular dust cover, using a flat head screw driver and a mallet I prised it off. Underneath will reveal a 32mm hub nut (impact gun recommended). With the hub nut removed the ABS ring can be removed (I ended up using a magnetic pick up tool to help). Next up is to remove the stub axle, this was a little trickier due to limited tools. I tried a 3 leg puller but the gap between the hub and stub axle wasn't enough for the legs to get in and under. Next option was a lump hammer and someone pulling the stub axle at the same time. After a few heavy hits it released. The lower bearing race had seized itself onto the stub axle, which was fine because I was replacing them anyway. With the upper bearing race removed and the grease cleaned off they looked like this The left one looked pristine inside but gave us the most trouble. The right one had some surface rust but came apart in a single hit, figure that out?! I got a local garage to press the new wheel bearings in, reassemble was the opposite and didn't take long at all. Removing the hub itself was simple. Starting with removing the brake caliper, 2x 14mm bolts for the caliper slider and 2x 19mm? for the carrier > hub bolts. I used a cable tie to secure the caliper to the upper arm so it was out of the way, there's a 10mm bolt securing the ABS sensor on. With the brake disc removed from the hub next are the three castle nuts for the upper and lower ball joints and track rod end. Two of these had their own R clip and one split pin. A few hits with the hammer and they're released (I left the castle nuts on by a couple of turns), the track rod ends gave me the most grief and I may have nipped the boots (oops). Fitting is the reversal and is very quick and easy to do. The lower ball joints are held onto the hub by 2x 17mm bolts. The castle nut did increase in socket size to 22mm from memory (this may vary from supplier) The two front tyres weren't in great condition, so I had those replaced with some budget tyres for the time being. I'll be replacing the wheels and tyres in the future, this was to get me on the road without the worry of the police hassling me.
    • Yep, the closest base tune available was for the GTT, I went with that and made all the logical changes I could find to convert it to Naturally Aspirated. It will rev fine in Neutral to redline but it will be cutting nearly 50% fuel the whole way.  If I let it tune the fuel map to start with that much less fuel it wont run right and has a hard time applying corrections.  These 50% cuts are with a fuel map already about half of what the GTT tune had.  I was having a whole lot of bogging when applying any throttle but seem to have fixed that for no load situations with very aggressive transient throttle settings. I made the corrections to my injectors with data I found for them online, FBCJC100 flowing 306cc.  I'll have to look to see if I can find the Cam section. I have the Bosch 4.9 from Haltech. My manifold pressure when watching it live is always in -5.9 psi/inHg
    • Hi My Tokico BM50 Brake master cylinder has a leak from the hole between the two outlets (M10x1) for brake pipes, I have attached a photo. Can anyone tell me what that hole is and what has failed to allow brake fluid to escape from it, I have looked on line and asked questions on UK forums but can not find the answer, if anyone can enlighten me I would be most grateful.
    • It will be a software setting. I don't believe many on here ever used AEM. And they're now a discontinued product,that's really hard to find any easy answers on. If it were Link or Haltech, someone would be able to just send you a ECU file though.
×
×
  • Create New...