Jump to content
SAU Community

Eastlink

justntime

By justntime,
in Victoria

 Share

Recommended Posts

justntime Contributor

justntime

Posted
Posted

Subject: Fw: Speed cameras - Eastlink

The locations are as follows :

WELLINGTONROAD ROWVILLE OVERPASS BRIDGE BOTH DIRECTIONS 6 CAMERAS 3 IN EACH DIRECTION.

These camera's are mounted high up in the honeycomb design of the underbelly and special attention has been given that they not be seen from either direction.

GREENS ROAD DANDENONG OVERPASS BRIDGE BOTH DIRECTIONS 6 CAMERAS 3 IN EACH DIRECTION.

Conditions of installation same as above.

EASTLINK TUNNEL RINGWOOD 12 CAMERAS 6 EACH SIDE.

These cameras are located at station boxB22and can move on special slide rails that allow them to be moved forward or backwards between station BoxB22and B35. these are expected to raise the most revenue.

FRANKSTON FREEWAY TO GREENS ROADOVERPASS DISTANCE 17 STRAIGHT KMS. (IDEAL DRAG STRIP)

This area is of major concern for the State Government, at this stage no legislation has been passed for the installation of cameras in either direction until you hit the Green Rd Bridge. Signs have been erected along this 17km strip that indicate 'Speed cameras operate in this area' in both directions but nothing is operating. The Government does not want to project itself as an immediate cash cow and as a result will not introduce them until next year at this stage.

They have placed into the road when the bitumen was poured, electronic trackers which are a new system of detection that works like the ones on the Geelong Freeway that measure you by Time Vs Speed.These are still being tested and measured for accuracy and efficiency.

It is possible that random mobile units may be deployed or hand held speed guns used as it is feared that this strip has become nick named the Dandy Dragstrip by the workers.

:D

:D:):O

Link to comment
https://www.sau.com.au/forums/topic/221945-eastlink/
Share on other sites
UNR33L Grand Master

UNR33L

Posted
Posted
hey, are we goin to have an eastlink cruise before they turn the toll gates on?

yeah there will be, either in the vic member section or events section just keep eyes open :D can't wait to block 3-4 lanes of skylines ahead and behind in the rear-view nothing beats teh sound too.

Link to comment
https://www.sau.com.au/forums/topic/221945-eastlink/#findComment-3916957
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Latest Posts

    • The Mafia
      Borg Warner EFR Series Turbo's V 2.0

      By The Mafia · Posted

      My EFR 8474 Black, made 800awhp on a roller dyno. at 25-26psi. E85. Shaft speed was around 106,000rpm 1.01 rear. The rear is maxed.  6 boost Turbosmart 60mm gate 3.5inch exhaust  Head is worked to the shithouse. Bain racing. VCam. 272 exhaust. RB28 - RB26 foundation.  You have an intake issue. Start getting proper data and I mean go back to the simple things.  - Pressure test your intake - Block off the Turbo BOV, you don't need it.  - Test pressure before and after your intercooler If your head is pretty stock, that is your issue. Especially if it is NA.  Take it off and spend $10k on it. 
    • MBS206
      Mistakes were made, my R34 Story

      By MBS206 · Posted

      Temp = -21.052 X Voltage + 114   That should get you pretty close. Calcs based on two points I could do easy calcs on (30 and 70 degrees).   It also says your sensor should only read as low as 9 degrees when it maxes out at 5V, and should hit a peak of 114 degrees at 0V... Just as a heads up if you were going really cold places, or wanting to be aware when temps really go up with it.
    • itsforandres
      BCNR33 Blower Motor Resistor - Testing

      By itsforandres · Posted

    • itsforandres
      BCNR33 Blower Motor Resistor - Testing

      By itsforandres · Posted

      you, sir, are a prince. good on ya.   
    • joshuaho96
      Are you an oil nerd?

      By joshuaho96 · Posted

      You're not wrong but 5W30 at 100C is like 10 cSt vs 25 cSt for 10W60. If we think in terms of viscosity margin 10W60 will probably still be ok at 130C but 5W30 is probably too little. It's absolutely shocking how hot the oil gets in something like a stock FL5 from only ~3 minutes of use on the Nordschleife. I would not risk taking a car like that to anything remotely intense without a ton of work done for cooling. Heat shielding on the manifold/turbo/downpipe, oil coolers, etc. 
×
×
  • Create New...