Jump to content
SAU Community

Eastlink

justntime

By justntime,
in Victoria

 Share

Recommended Posts

justntime Contributor

justntime

Posted
Posted

Subject: Fw: Speed cameras - Eastlink

The locations are as follows :

WELLINGTONROAD ROWVILLE OVERPASS BRIDGE BOTH DIRECTIONS 6 CAMERAS 3 IN EACH DIRECTION.

These camera's are mounted high up in the honeycomb design of the underbelly and special attention has been given that they not be seen from either direction.

GREENS ROAD DANDENONG OVERPASS BRIDGE BOTH DIRECTIONS 6 CAMERAS 3 IN EACH DIRECTION.

Conditions of installation same as above.

EASTLINK TUNNEL RINGWOOD 12 CAMERAS 6 EACH SIDE.

These cameras are located at station boxB22and can move on special slide rails that allow them to be moved forward or backwards between station BoxB22and B35. these are expected to raise the most revenue.

FRANKSTON FREEWAY TO GREENS ROADOVERPASS DISTANCE 17 STRAIGHT KMS. (IDEAL DRAG STRIP)

This area is of major concern for the State Government, at this stage no legislation has been passed for the installation of cameras in either direction until you hit the Green Rd Bridge. Signs have been erected along this 17km strip that indicate 'Speed cameras operate in this area' in both directions but nothing is operating. The Government does not want to project itself as an immediate cash cow and as a result will not introduce them until next year at this stage.

They have placed into the road when the bitumen was poured, electronic trackers which are a new system of detection that works like the ones on the Geelong Freeway that measure you by Time Vs Speed.These are still being tested and measured for accuracy and efficiency.

It is possible that random mobile units may be deployed or hand held speed guns used as it is feared that this strip has become nick named the Dandy Dragstrip by the workers.

:D

:D:):O

Link to comment
https://www.sau.com.au/forums/topic/221945-eastlink/
Share on other sites
UNR33L Grand Master

UNR33L

Posted
Posted
hey, are we goin to have an eastlink cruise before they turn the toll gates on?

yeah there will be, either in the vic member section or events section just keep eyes open :D can't wait to block 3-4 lanes of skylines ahead and behind in the rear-view nothing beats teh sound too.

Link to comment
https://www.sau.com.au/forums/topic/221945-eastlink/#findComment-3916957
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Latest Posts

    • oHBoy.
      2001 R34DE

      By oHBoy. · Posted

      lol the 2nd one boss, thank you for pointing this out. I feel as i spend more time here this intro message is some thing i will always make me laugh and shake my head at. Perfect Intro:  I have the vehicle  
    • PranK
      2001 R34DE

      By PranK · Posted

      R34DE as in R34 with an RB25DE? So did you get this? Or you planning to?  I'm not really sure what you're saying. 
    • Dose Pipe Sutututu
      What should I do next to hold the head on

      By Dose Pipe Sutututu · Posted

      Possibly avoid using a Cometic one unless the deck/head surface are perfectly flat. I did have a look just then and forgiving gaskets such as Tomei or Nitto don't exist for the FJ20, however the Bar-Tek or Kameari ones look good and might do the trick.
    • GTSBoy
      boost source Size Garrett gt28 gen2

      By GTSBoy · Posted

      Because pipe threads for pipe things. M threads for bolt things. Throw some teflon sealant onto it and dust your hands off knowing you did the right thing, instead of going twice around the block to achieve a result using the wrong things. Of course, all of these solutions are ignoring the fact that the minimum thread pitch we're talking about here is 1.25mm, with the 1/4" in NPT or BPS being out around 1.4mm. You will need to know that the boss you're tapping has enough thickness for at least a few threads. That's one of the reasons that 1/8" is commonly used - because the pitch is <1mm. And why would you look to use 1/4" NPT in a BSP country anyway? Ugh.
    • Dose Pipe Sutututu
      boost source Size Garrett gt28 gen2

      By Dose Pipe Sutututu · Posted

      Just throwing around ideas, does it need to be in the compressor cover? Why not the hot side piping?
×
×
  • Create New...