Jump to content
SAU Community

Eastlink

justntime

By justntime,
in Victoria

 Share

Recommended Posts

justntime Contributor

justntime

Posted
Posted

Subject: Fw: Speed cameras - Eastlink

The locations are as follows :

WELLINGTONROAD ROWVILLE OVERPASS BRIDGE BOTH DIRECTIONS 6 CAMERAS 3 IN EACH DIRECTION.

These camera's are mounted high up in the honeycomb design of the underbelly and special attention has been given that they not be seen from either direction.

GREENS ROAD DANDENONG OVERPASS BRIDGE BOTH DIRECTIONS 6 CAMERAS 3 IN EACH DIRECTION.

Conditions of installation same as above.

EASTLINK TUNNEL RINGWOOD 12 CAMERAS 6 EACH SIDE.

These cameras are located at station boxB22and can move on special slide rails that allow them to be moved forward or backwards between station BoxB22and B35. these are expected to raise the most revenue.

FRANKSTON FREEWAY TO GREENS ROADOVERPASS DISTANCE 17 STRAIGHT KMS. (IDEAL DRAG STRIP)

This area is of major concern for the State Government, at this stage no legislation has been passed for the installation of cameras in either direction until you hit the Green Rd Bridge. Signs have been erected along this 17km strip that indicate 'Speed cameras operate in this area' in both directions but nothing is operating. The Government does not want to project itself as an immediate cash cow and as a result will not introduce them until next year at this stage.

They have placed into the road when the bitumen was poured, electronic trackers which are a new system of detection that works like the ones on the Geelong Freeway that measure you by Time Vs Speed.These are still being tested and measured for accuracy and efficiency.

It is possible that random mobile units may be deployed or hand held speed guns used as it is feared that this strip has become nick named the Dandy Dragstrip by the workers.

:D

:D:):O

Link to comment
https://www.sau.com.au/forums/topic/221945-eastlink/
Share on other sites
UNR33L Grand Master

UNR33L

Posted
Posted
hey, are we goin to have an eastlink cruise before they turn the toll gates on?

yeah there will be, either in the vic member section or events section just keep eyes open :D can't wait to block 3-4 lanes of skylines ahead and behind in the rear-view nothing beats teh sound too.

Link to comment
https://www.sau.com.au/forums/topic/221945-eastlink/#findComment-3916957
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Latest Posts

    • Dose Pipe Sutututu
      UniClutch

      By Dose Pipe Sutututu · Posted

      Another one
    • TurboTapin
      Leaking Rear Subframe Bushing?

      By TurboTapin · Posted

      Yes, I had ordered the spherical bushings at the same time as the rest. I have high hopes for the anti squat reduction kit. 
    • GTSBoy
      Leaking Rear Subframe Bushing?

      By GTSBoy · Posted

      Make sure you use the spherical bushes** on the lower arms, ifyou do that. ** at least, if not the whole replacement lower arm.
    • GTSBoy
      R32 only blows hot air

      By GTSBoy · Posted

      The tap for coolant flow control will be stuck open. It's not just the air door motor that dies.
    • Duncan
      R32 only blows hot air

      By Duncan · Posted

      Not really, but the heater box is pretty simple mechanically....if the door is one way the air bypasses the heater core and if it is the other way it goes through it for warm air.  If you are sure the actuator you moved manually is for the heater mix (there would also be one for output air direction) then I'd take the heater box out and see what is happening (you'll have to regass and re-coolant the systems afterwards) BTW pp724 onwards from the GTR workshop manual cover the system in good detail, it is probably worth checking. I think the IAT sensor might be a problem electrically for getting cold (if you got 24 error code not -24 it thinks the incoming air is -50c) and it covers how to test the sensor (although most likely it is either not plugged in or a wire is damaged)
×
×
  • Create New...