Jump to content
SAU Community

Recommended Posts

i'm off to get my 2835 installed in a couple of weeks so i decided to do a few of the less time consuming supporting mods myself... (fuel pump etc)

so i installed some new splitfire coils and some bcpr7es gapped to 0.8... and put the car back together

when i took it for a drive i noticed 2 things...

1) it feels smoother and more linear throughout the rev range

2) its running less boost. ?!

formerly i was getting .9 bar with boost controller (bleeder) switched off but spiking out to 1.1

now its getting .5 bar and not spiking past .55

so i turned up the bleed valve to .8 bar and it holds nicely without spiking past .85ish

car has pfc, fmic, turbo back etc. how much boost shold it be producing with these mods?

also when the car was tuned a year ago @ racingline, nige said there was a tiny leek that he didn't have time to locate,(i needed transport back) but the car was running fine and not to worry. the car ran strong for a year with no problems.

so... my question is this...

was the car running with a leek that was acting like a bleed valve and upping the boost for a year

OR

did i not put a hose on properly this time? (i have checked and checked again...)

Link to comment
https://www.sau.com.au/forums/topic/222437-interesting-problem/
Share on other sites

Oh and they're gapped to .8 cause i've been told by many many people that would be the optimum gap...

On a stock ecu/tuned car running 98ron yes

With an aftermarket ecu, tuned and new splitfires your gap should be 1.1..

The idea of setting the gap to .8 is a cheap get around for the pinging/breakdown issues most skylines have on 98ron when using the factory tune.

It's a stop gap, for peeps that can't do it the right way atm...with your parts you shouldn't be bothering with that crap.

Embrace the strength of a bigger spark!!

I did the same thing when I first got my nissan, until I got around to doing it right.

i dunno... taking all that shit off again... might give it a go when i get round to installing those injectors that are still sitting in the box next to my bed :thumbsup:

any ideas on the prob guys?

Even once the coilpacks are "coated in silicon" the car will fart and miss above 5000RPM if you gap is at 1.1mm WHERE IT IS MEANT TO BE!

Once you chuck the Splitfires in, (Or even BRAND NEW stock coilpacks) you will be able to gap plugs to 1.1mm AND rev to redline perfectly cleanly, producing a better flame front in your engine.

Technically, from what I can gather, it will also allow you to run slightly more advanced timing when you do the tune, as you have a wider initial flame front.

Hence @ 1.1mm you should be able to make more power cleanly...

Even once the coilpacks are "coated in silicon" the car will fart and miss above 5000RPM if you gap is at 1.1mm WHERE IT IS MEANT TO BE!

Once you chuck the Splitfires in, (Or even BRAND NEW stock coilpacks) you will be able to gap plugs to 1.1mm AND rev to redline perfectly cleanly, producing a better flame front in your engine.

Technically, from what I can gather, it will also allow you to run slightly more advanced timing when you do the tune, as you have a wider initial flame front.

Hence @ 1.1mm you should be able to make more power cleanly...

Depends on a variety of things but, in this case the 0.8mm gap is going to be better at high rpm/boost and power levels in terms of reliable spark.

1.1mm is a nice gap for a cleaner burn at lower rpm, hence it's factory.

The factory coils are just as good as splitfires by the way. Splitfires are just cheaper to buy new.

Depends on a variety of things but, in this case the 0.8mm gap is going to be better at high rpm/boost and power levels in terms of reliable spark.

1.1mm is a nice gap for a cleaner burn at lower rpm, hence it's factory.

The factory coils are just as good as splitfires by the way. Splitfires are just cheaper to buy new.

How do you figure a smaller spark is better on higher boost?

Gapping down is a very basic and simplistic way of advancing timing...used to get around pinging on a stock non-tunable ecu.

If you tune the car correctly with 1.1 gap it is better...you can actually feel the difference in top end, revs more freely.

Splitfires don't create more horsepower, but they do give a stronger spark (%20?) which certainly helps.

But hey if 8 is your lucky number.... who am I to say different.

How do you figure a smaller spark is better on higher boost?

Gapping down is a very basic and simplistic way of advancing timing...used to get around pinging on a stock non-tunable ecu.

If you tune the car correctly with 1.1 gap it is better...you can actually feel the difference in top end, revs more freely.

Splitfires don't create more horsepower, but they do give a stronger spark (%20?) which certainly helps.

But hey if 8 is your lucky number.... who am I to say different.

I'm sorry but, 'feeling the difference' in top end?

Unless the tune was rooted before I can assure you that not only is there no power difference but, also this 'feeling' is peculiar only to cars that started out with a spark issue or were seriously 'under-gapped' for the density of the air/fuel mixture.

Smashing more power/rpm/boost into a motor and gapping down on the exsisting heat range is tuning 101( for all cars). If you get no joy in the top end after gapping down on the exsisting heat range you go to a colder plug etc.

For example, for most of the NA V8's I've tuned you can just about go off a rule of thumb that is gap down 4 thou for every 50hp added.

I've been doing this to alot of different cars over the years so 'luck' has nothing to do with it. :)

There are some serious horsepower GTST's & GTR's running around with factory coils as well. Splitfires do one thing well and thats make a cheap replacement for the expensive factory coils when they are shagged. :D

Edited by rev210

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hello all I have 2 r34 sedans , one turbo one na, only recently aquired the na 34.  Man what is with these things.... My turbo 34 started sounding like a super charger, it was screaming at anything above 4000rpm , I took the alternator apart and replaced the front bearing which is the only one I think you can access and it did not fix the issue so presumably the bearing in the rear of the alternator is gone. ( diagnosed it was the alternator by taking off the aux belts one by one to figure out which pulley or bearing it was )  My friend gave me one he had lying around, Installed it , it did not squeal for maybe 500kms and now its started to squeal again briefly on startup  Recently got an na r34 and I replaced the timing belt, water pump + all the auxillirary belts. Runs amazing but it suddenly developed the same squeaking problem but significantly worse, Ive had my neighbour come down screaming at me because it was waking her up everytime I moved the car. It takes a good 2 minutes before it quietens down.  Im yet to diagnose where its coming from but im fairly sure its coming from the alternator aswell. My question isnt about how to fix it but rather where can you get a new alternator for an rb25 neo??? Ive searched everywhere but I havent been able to find a direct fit oem type replacement thats not genuine. All the automotive stores sell an oex one - BXA035 - which I picked up for cheap through a friend with staff discount , got it home only to find the connector is completelty different.... As far as im aware bxa035 is for rb20/30's and after a bit of figuring out the bxa035 has an ev14 type connector, which is tiny compared to the rb25 connector. I actually had an ev14 connector lying around which I was considering just replacing the bigger plug with to get the alternator working but the bxa035 is rated for 70amp vs the rb25 alternators are 90amp ( or so ive been told ? ) That paired along with the fact im about to install an amp + sub in the back and I have the stock sized small battery Im not sure itll do the job unless anyone has another opinion?  I know and have seen all the websites selling the ls1 alternator conversion kit but I am not going down that route, nor do I have the money to. Hopefully I can figure out how to get 2 brand new alternators for both cars. I would buy second hand which there seems to be many of but considering how common this seems to be im sure If I installed a second hand one it would start squealing in no time  Or even better if anyone knows how to fix the issue directly with the alternator itself... Any input appreciated Thank you     Link for bxa035 connector picture
    • As above, replace as many as you can afford. If anything, due to old age.
    • Can confirm previous shop that built my motor had no fking clue about oil control and caused my motor to shit itself after two track days. Current shop, Birrong Automotive, has managed to build me a motor, not to mention, has also let me tune it myself and it has yet to blow up after 7 track days. Great oiling success, yashimash.
    • It definitely seems like you have no beef, with only digging up a 5 year old post, to comment on an inflammatory item with total insensitivity, and of which had nothing to do with the thread.  Yep, you definitely seem like a great person and your friends and family would be so proud to know of your lovely actions
    • Thanks buddy, so happy to be back! Managed to pickup a Unicorn R34 completely stock and clean. Looking forward to adding some goodies to it and posting one here. I'm shocked that so many forums stopped. If you could find my old profile - I'd love that if its possible. My old account was JET200GT. My email might need to be fixed too. To use this one. I think it was the same though..
×
×
  • Create New...