Jump to content
SAU Community

Recommended Posts

  • 2 weeks later...

Fired it up this morning.

(typical crap sound quality due to engine noise)

It's all untuned and just running on the start-up mode, hence the big lumpy idle. It wont take throttle yet, but at least it runs under it's own steam.

What ID are the toyota throttles?

42mm.

The tune on Thursday will just be a temporary measure, so that I am able to run the car at a test day on Monday to find all the problems before going to the final tune and dialing up the cams fully. Just want to be able to turn the wheels again, been a long couple of months.

I have to ask, with your choice of ECU, does the Link do a lookup comparison between MAP and TPS?

With ITB, you'll find that at different throttle positions, you get the same pressure behind the throttle body (Headed for the motor) but, you're actually getting different air, especially since you get a lot of air turbulence.

This is where you'll LOSE out on your throttle response, and get a drop in power, if it's not able to be tuned properly.

The Adaptronic which was mentioned earlier, does exactly this. The GTR doesn't have to worry about anything of the likes until you go MAP sensor on it. And then it sees the exact same issue.

Also to the person saying the Adaptronic runs unreliable drivers... I'd like to ask, SINCE WHEN?

Just a quick update. No pic's/vid's at the mo, haven't got time.

The car is up and running. Has much more torque, good throttle responce and sounds awsome!

Ran the car at two gravel hillclimbs on the weekend and found the extra torque very usable off the turns.

My mate is currently making some longer trumpets based off the info from the dyno run. This will mean we can dial in a wider power band from the cams and complete the tune. In the meantime I'm jut getting on with racing the thing again.

  • 1 month later...

I've done a few events with the ITB setup now and I have been very impressed with the results.

The car pulls much stronger in the mid-range, which is where I need it and it still rev's out easily to 8k. The throttle responce mid corner is instant and I am able to use more control when I'm looking for grip and there are no flatspots anywhere in the rev range from 3500rpm on.

The video below is of a steep hill we ran up a couple of weeks back. Compared to last year, I found it far more driveable and easier to keep momentium.

http://nz.youtube.com/watch?v=pjSTmw_WWqs

Still more tuning to be done, so hopefully with a few adjustments I'll have a wider powerband to play with.

picture001smlzy8.jpg

Edited by screamin'
  • 3 weeks later...

What power did it end up making and what torque?

Do you have a dyno graph?

Sounds really nice, good to see people doing something out of the mainstream and the engine bay looks really neat.

Don't have figures for the torques or ponies, wasn't too fussed about that and at the end of the day numbers don't mean much on gravel.

It has great midrange torque for a 2ltr and this makes the car far more drivable and controlable through the corners, when compared to the same events last year.

Why would itb's be illegal, unless you guys have some emission controls or something over there, which means in that case my SS is illegal too.

After the first event the engine bay is now really dusty, so it didn't look that good for long!

  • 4 months later...

Been running it for a while now. Car is going real good, had a couple of 1st in class (1600-2000cc) and a 1st two wheel drive on one hill climb. Good to be beating the Escorts and Tereno's.

Got a couple of short vid's of last weekends rallysprint. Day started off at -5°C and didn't get much warmer!

Some photo's. Check out the frozen road!

http://www.colourandlight.co.nz/galleries/...ne09/index.html

  • 2 months later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • I'm normally copping my own abuse from neglecting my daily drivers. "Those suspension bushes will last a bit more", "Don't worry about the oil leak, just keep topping it up". The project cars I'm always doing things slowly on them as I'm wanting them to be done better, and neater, and nicer. Luckily I don't have to deal with 18 year old Matt's "Learning to wire" stuff in the project cars. And there's only one piece of wiring I'm displeased about in the Landcruiser, and it's about to be cut out... However, the box loads of parts that have been going through this place lately for the Landcruiser... Brake pads Brake Rotors Full handbrake overhaul Wheel Bearings Seals Swivel hubs Steering Boxes Half the suspension joints Shocks Air bags (Ones to go in the rear springs for towing) Water pump Timing kit Lower timing case Harmonic Balancer Radiator Lots of other little seals and shits Gas struts for the bonnet New power window switches And god knows what else I've forgotten... Ha ha ha I have my fingers crossed the pinion seals don't start leaking on the diffs, that the transfer case doesn't leak, and the gearbox input shaft doesn't leak, nor the rear main seal. As they're about the only seals I haven't replaced in the driveline! I'm seriously eyeing off buying new caliper rebuild kits front and rear brake calipers... I'll probably recheck all the valve clearances soon too, and hopefully, it should be all good and sweet to haul some long distance trips again!
    • Every time I pull my 3x gauges out of the console and see the crack-addict way that I did the wiring, and I just can't bring myself to tear it all apart and "make it nice", because it is currently working. In fact, the last time I was in there I probably made it worse.
    • The best part is when you own the car long enough that you look back and find your OWN ham fisted amateur shit!
    • The annoying part about neglect, is when you start to replace one thing, and find ten more broken things. Ham fisted monkey repairs you normally only find out about when trying to do something unrelated! Ha ha   Neglect you can kind of anticipate the huge costs to fix it all. Ham fistedness is normally a shock the first time your work on a new old car, as everything "looked" good before.
    • For DBA, check out their guide table here. https://dba.com.au/wp-content/uploads/2023/01/Direct_Replacement-Guide-2021.2.pdf   Additionally they have some other guides and info on how to make sure you choose the right pad.
×
×
  • Create New...