Jump to content
SAU Community

Recommended Posts

Just wondering if anyone can help. I bought a 1998 S2 RS4 S Stagea about 8 months ago.

I recently did my first mod and it was a k and n pod filter, other than that my stagea is stock as a rock. Since doing this mod ive noticed that my car is spiking a couple of pound according to the boost gauge but only sometimes. occasionally when it spikes i get a big miss, it sounds as like tiney little pops coming out the exhaust, several of them. And i lose power. If i keep my foot down it clears and i get power again and if i take my foot off and try again it doesnt do it. can anyone help?

It doesnt sound real healthy and i dont want 2 do any damage

Thanks

Link to comment
https://www.sau.com.au/forums/topic/223011-stagea-miss/
Share on other sites

Sounds like it is hitting 'rich and retard', plenty of info about this throughout this forum, but basically you probably need to start thinking about, depending on your budget and plans, a minimum AFC (apexi Air fuel controller). This is because since your pod filter was installed the ECU is detecting a larger amount of air entering the engine than normal, via the air flow meter, and is keeping things 'safe' by increasing the fuel and retarding the ignition. Not a great problem, something we all hit once the mods start.

Link to comment
https://www.sau.com.au/forums/topic/223011-stagea-miss/#findComment-3929429
Share on other sites

Im having the same problem aswell... My 1997 Stagea has a FMIC and Pod filter and was running stock boost no problems.. as soon as i put the boost controller on and raised it to 11-12psi its popping and missing under heavy load..

Link to comment
https://www.sau.com.au/forums/topic/223011-stagea-miss/#findComment-3929627
Share on other sites

I found when i boosted my stag over 10psi it started to hit Rich & Retard and the turbo would spool really quickly and then ping its guts out. i was told the stageas have a fuel cut over 10psi, thought how it detects that is beyond me. basically i turned the boost down to 10psi and haven't had any dramas since

Link to comment
https://www.sau.com.au/forums/topic/223011-stagea-miss/#findComment-3929814
Share on other sites

it detects it by reading the voltage of the AFM, once the ECU detects a certain voltage it will go into rich and retard, hence why AFC's stop this when they are tuned correctly, ie most of the time leaned out to give better Air fuel ratios by reducing the AFM voltage at the ECU.

Mods like pod filter, exhaust, more boost will bring it on.

Link to comment
https://www.sau.com.au/forums/topic/223011-stagea-miss/#findComment-3929848
Share on other sites

Will either be Rich and Retard or a missfire caused by old or incorrectly gapped plugs or one or more ignition coils are on thier way out. If your still running stock boost and as you say everything else on the car is dead stock I doubt it'll be R&R. I'd try a new set of plugs gapped at 0.8 and see if this fixes it and go from there. Can you say at what RPM this happens, I was having serious spark break down from about 3000rpm through to about 4500rpm if it even got that far. My coils were stuffed, fitted splitfires and its running better than it ever has. But I'd start with the cheap options first.

Link to comment
https://www.sau.com.au/forums/topic/223011-stagea-miss/#findComment-3929850
Share on other sites

had mine gapped at .8 mm before my exhaust and fmic. after they were fitted i found that the spark seemed to break down at 5000 rpm + only when driving hard . sold the car before i gaped the plugs smaller but 99 percent shure that was the problem.. started to wander down the rich and retard path but ended up being the garden path :D

Link to comment
https://www.sau.com.au/forums/topic/223011-stagea-miss/#findComment-3929978
Share on other sites

Will either be Rich and Retard or a missfire caused by old or incorrectly gapped plugs or one or more ignition coils are on thier way out. If your still running stock boost and as you say everything else on the car is dead stock I doubt it'll be R&R. I'd try a new set of plugs gapped at 0.8 and see if this fixes it and go from there. Can you say at what RPM this happens, I was having serious spark break down from about 3000rpm through to about 4500rpm if it even got that far. My coils were stuffed, fitted splitfires and its running better than it ever has. But I'd start with the cheap options first.

yeah it seems to be round 3000 rpm to about 5000 rpm then after that it seems to go away. thanks for the suggestions. Will try plugs and then coilpacks. If that doesnt fix it then ill go further. Process of illumination always works. used to have a vl commodore with rb25 conversion pumping out 250rwkw, never had any problems like this with that, hense being abit worried.

Thanks

Link to comment
https://www.sau.com.au/forums/topic/223011-stagea-miss/#findComment-3930056
Share on other sites

I found when i boosted my stag over 10psi it started to hit Rich & Retard and the turbo would spool really quickly and then ping its guts out. i was told the stageas have a fuel cut over 10psi, thought how it detects that is beyond me. basically i turned the boost down to 10psi and haven't had any dramas since

Nice looking stagea, i want 2 buy a tow bar or get 1 custom made 4 mine, where about did u get or who made it 4 u?

Link to comment
https://www.sau.com.au/forums/topic/223011-stagea-miss/#findComment-3930069
Share on other sites

yeah it seems to be round 3000 rpm to about 5000 rpm then after that it seems to go away. thanks for the suggestions. Will try plugs and then coilpacks. If that doesnt fix it then ill go further. Process of illumination always works. used to have a vl commodore with rb25 conversion pumping out 250rwkw, never had any problems like this with that, hense being abit worried.

Hi mate,

Straight up Im no mechaninc but Id like to voice my opinion.... By the sounds of it one of your coil packs is stuffed or the plugs need changing/gapping. Does it feel like the car is sort of jolting for a bit when you put the foot down then in goes back to normal after about 5kish rpm? My mates stag was doing this and it had 2 of the coil packs replaced and all the plugs and its fine now. Hunt around for some splitfire coilpacks and get them on their as for plugs their are many threads just do a search.

Also if you still have the stock air box drive it with the pod and make sure its making the problem, go home chuck on airbox and go again just to rule that out of the picture. Id be highly supprised if the pod is whats giving you trouble.

Good luck mate.

Link to comment
https://www.sau.com.au/forums/topic/223011-stagea-miss/#findComment-3931679
Share on other sites

Hi mate,

Straight up Im no mechaninc but Id like to voice my opinion.... By the sounds of it one of your coil packs is stuffed or the plugs need changing/gapping. Does it feel like the car is sort of jolting for a bit when you put the foot down then in goes back to normal after about 5kish rpm? My mates stag was doing this and it had 2 of the coil packs replaced and all the plugs and its fine now. Hunt around for some splitfire coilpacks and get them on their as for plugs their are many threads just do a search.

Also if you still have the stock air box drive it with the pod and make sure its making the problem, go home chuck on airbox and go again just to rule that out of the picture. Id be highly supprised if the pod is whats giving you trouble.

Good luck mate.

I put a new set of plugs in and had them gapped by my mechanic. im not sure if it was doing this before i put the pod on as i didnt have the car long b4 i modded it. The problem with this problem is that it only happens sometimes, very rarely actually and u would think if it was a coil pack braking down it would be getting worse or happening all the time. Ill start off with coil packs and new plugs then go from there

Thanks

Link to comment
https://www.sau.com.au/forums/topic/223011-stagea-miss/#findComment-3933196
Share on other sites

When my coils started to go it was very intermittant (spelling :ermm: ) at first. This was about a year or so ago now, then got a little bit worse as the months went on, wait till the warmer weather comes back then you'll notice it :geek: Then just got to the stage where the car was chewing a lot of fuel (more than usual for a stagea) and even 1/2 throttle would cause break down in spark. Once the splitfires were in its been a dream to drive :huh: I've still got my factory coils, don't know which ones are stuffed though?

Link to comment
https://www.sau.com.au/forums/topic/223011-stagea-miss/#findComment-3933798
Share on other sites

When my coils started to go it was very intermittant (spelling :wacko: ) at first. This was about a year or so ago now, then got a little bit worse as the months went on, wait till the warmer weather comes back then you'll notice it :) Then just got to the stage where the car was chewing a lot of fuel (more than usual for a stagea) and even 1/2 throttle would cause break down in spark. Once the splitfires were in its been a dream to drive :D I've still got my factory coils, don't know which ones are stuffed though?

Priced a set of splitfires $520, anyone see any cheaper anywhere

Link to comment
https://www.sau.com.au/forums/topic/223011-stagea-miss/#findComment-3934304
Share on other sites

  • 1 month later...

I'm currently experiencing something that sounds very similar to the original poster's issue.

Misfire on boost and above half throttle, from about 3-5000rpm. Initially we thought it was as the car had run low on fuel, as chucking $30 worth of fuel in seemed to fix it, although it still missed up near 6k rpm...for about 15 minutes then the misfire came back just as before.

Changed plugs, fuel filter etc, still not sorted.

Coilpacks look 100% fine (in my experience the classic internet mechanic fix of changing them just masks the real issue anyway).

Its an auto late '97 S1 with a pod filter and full Nismo exhaust, test gauge says 10psi maximum with no spiking any higher.

I couldn't discern a big fuel cloud in the mirrors though..... All that strikes me is fuel pump perhaps?

Any ideas?

Edited by floody
Link to comment
https://www.sau.com.au/forums/topic/223011-stagea-miss/#findComment-4024555
Share on other sites

Coilpacks look 100% fine (in my experience the classic internet mechanic fix of changing them just masks the real issue anyway).

Yeah my coilpacks looked good too (I think you really need to check them with a multimeter.)

I had this problem for the last few weeks, and was a bit wary of jumping in and following forum suggestions but decided to risk it and get some new plugs and splitfires.

Figured changing the plugs might fix it but figured I didn't want the same problem again in three weeks time so the splitfires were probably a good invesment.

The guys are 100% right. Not only did it fix the misfire, but seems to be better through the entire rev range. (very smooth :( )

I decided to go with the platinum plugs with 1.1 mm gap as my car is 100% standard (S2 25t x four).

A lot of guys are running a .08 gap but I think most of them have modified cars.

Anyway, I was cheering. Very grateful for the advice handed out on this forum.

Link to comment
https://www.sau.com.au/forums/topic/223011-stagea-miss/#findComment-4024707
Share on other sites

I'm wary of spending money on coilpacks as usually you end up replacing perfectly functional items, only to find further down the track that it was the loom, CAS or similar that was the real problem.

If it is coilpacks...WTF is up with their quality in late model skylines? I have 20 year old ones in my HR31 which are still in A1 condition, but seems R32/33/Stag items crap out inside a decade.

Link to comment
https://www.sau.com.au/forums/topic/223011-stagea-miss/#findComment-4024815
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Look, realistically, those are some fairly chunky connectors and wires so it is a reasonably fair bet that that loom was involved in the redirection of the fuel pump and/or ECU/ignition power for the immobiliser. It's also fair to be that the new immobiliser is essentially the same thing as the old one, and so it probably needs the same stuff done to make it do what it has to do. Given that you are talking about a car that no-one else here is familiar with (I mean your exact car) and an alarm that I've never heard of before and so probably not many others are familiar with, and that some wire monkey has been messing with it out of our sight, it seems reasonable that the wire monkey should be fixing this.
    • Wheel alignment immediately. Not "when I get around to it". And further to what Duncan said - you cannot just put camber arms on and shorten them. You will introduce bump steer far in excess of what the car had with stock arms. You need adjustable tension arms and they need to be shortened also. The simplest approach is to shorten them the same % as the stock ones. This will not be correct or optimal, but it will be better than any other guess. The correct way to set the lengths of both arms is to use a properly built/set up bump steer gauge and trial and error the adjustments until you hit the camber you need and want and have minimum bump steer in the range of motion that the wheel is expected to travel. And what Duncan said about toe is also very true. And you cannot change the camber arm without also affecting toe. So when you have adjustable arms on the back of a Skyline, the car either needs to go to a talented wheel aligner (not your local tyre shop dropout), or you need to be able to do this stuff yourself at home. Guess which approach I have taken? I have built my own gear for camber, toe and bump steer measurement and I do all this on the flattest bit of concrete I have, with some shims under the tyres on one side to level the car.
    • Thought I would get some advice from others on this situation.    Relevant info: R33 GTS25t Link G4x ECU Walbro 255LPH w/ OEM FP Relay (No relay mod) Scenario: I accidentally messed up my old AVS S5 (rev.1) at the start of the year and the cars been immobilised. Also the siren BBU has completely failed; so I decided to upgrade it.  I got a newer AVS S5 (rev.2?) installed on Friday. The guy removed the old one and its immobilisers. Tried to start it; the car cranks but doesnt start.  The new one was installed and all the alarm functions seem to be working as they should; still wouldn't start Went to bed; got up on Friday morning and decided to have a look into the no start problem. Found the car completely dead.  Charged the battery; plugged it back in and found the brake lights were stuck on.  Unplugging the brake pedal switch the lights turn off. Plug it back in and theyre stuck on again. I tested the switch (continuity test and resistance); all looks good (0-1kohm).  On talking to AVS; found its because of the rubber stopper on the brake pedal; sure enough the middle of it is missing so have ordered a new one. One of those wear items; which was confusing what was going on However when I try unplugging the STOP Light fuses (under the dash and under the hood) the brake light still stays on. Should those fuses not cut the brake light circuit?  I then checked the ECU; FP Speed Error.  Testing the pump again; I can hear the relay clicking every time I switch it to ON. I unplugged the pump and put the multimeter across the plug. No continuity; im seeing 0.6V (ECU signal?) and when it switches the relay I think its like 20mA or 200mA). Not seeing 12.4V / 7-9A. As far as I know; the Fuel Pump was wired through one of the immobiliser relays on the old alarm.  He pulled some thick gauged harness out with the old alarm wiring; which looks to me like it was to bridge connections into the immobilisers? Before it got immobilised it was running just fine.  Im at a loss to why the FP is getting no voltage; I thought maybe the FP was faulty (even though I havent even done 50km on the new pump) but no voltage at the harness plug.  Questions: Could it be he didnt reconnect the fuel pump when testing it after the old alarm removal (before installing the new alarm)?  Is this a case of bridging to the brake lights instead of the fuel pump circuit? It's a bit beyond me as I dont do a lot with electrical; so have tried my best to diagnose what I think seems to make sense.  Seeking advice if theres for sure an issue with the alarm install to get him back here; or if I do infact, need an auto electrician to diagnose it. 
    • Then, shorten them by 1cm, drop the car back down and have a visual look (or even better, use a spirit level across the wheel to see if you have less camber than before. You still want something like 1.5 for road use. Alternatively, if you have adjustable rear ride height (I assume you do if you have extreme camber wear), raise the suspension back to standard height until you can get it all aligned properly. Finally, keep in mind that wear on the inside of the tyre can be for incorrect toe, not just camber
    • I know I have to get a wheel alignment but until then I just need to bring the rear tyres in a bit they're wearing to the belt on the inside and brand new on the outside edge. I did shorten the arms a bit but got it wrong now after a few klms the Slip and VDC lights come on. I'd just like to get it to a point where I can drive for another week or two before getting an alignment. I've had to pay a lot of other stuff recently so doing it myself is my only option 
×
×
  • Create New...