Jump to content
SAU Community

Recommended Posts

define "jdm" look.

i was running -6 rear and -4 front 17x9 with 215 tires for awhile. got sick of pizza cutter tires, now im +10 17x9 with a 255 tire, all 4 fenders rolled.

youre not going to get the "jdm" look without rolling your fenders. people here do it for 40 bucks a fender with the rolling tool and a heat gun

+1

  • 3 weeks later...
Perfect look in my opinion

18x9.5 +15 all around ! Rear are rolled/flared, front are rolled only

That's not my car, but on mine I'll probably go with work XD9 in 17x9.5 +17

dsc00260bid3.jpg

dsc00213ok1.jpg

dsc00216gk7.jpg

dsc00259ny2.jpg

hey just a quick question,

im looking at 18 x 9.5 CR kais for my 33, in the pic are they 18 x 9.5 with +15 offset? CR kais come with a +12 offset so that means theyll stick out n extra 3mm is that right?

i dont wanna fork out thousands of $$$ and get it wrong lol

hope you can help, thanks heaps

hey just a quick question,

im looking at 18 x 9.5 CR kais for my 33, in the pic are they 18 x 9.5 with +15 offset? CR kais come with a +12 offset so that means theyll stick out n extra 3mm is that right?

i dont wanna fork out thousands of $$$ and get it wrong lol

hope you can help, thanks heaps

Check this out : http://www.1010tires.com/WheelOffsetCalculator.asp

Sparco NS2's

18x9 front

18x10 rear

dunno my offset

post-53838-1229061301_thumb.jpg

post-53838-1229061393_thumb.jpg

post-53838-1229061329_thumb.jpg

If you haven't had your guards rolled, the offset on those rims must be very high...like +40 or higher at a guess...

my 9.5" +22's stuck out heaps on the rear

I'm running 18x9's with 265s on my R33 and have not had my guards rolled. I don't get any scraping either.

However my car isn't as low as a lot of 33's here seem to be but I'm not stock either.

Offset is key.

I'm running 18 9.5 +20 all round and have had the guards rolled, but it looks JDM.

Old pic, different front bar now.

lookin tuff!

bit lower perhaps? :)

auss13 - the offset is written on the inside of the rims :)

  • 1 year later...

TYRE SIZES TO KEEP THE SAME ROLLING CIRCUMFERANCE AS THE 16" FACTORY TYRE'S ARE FRONT 225/45/17 AND THE REARS 255/40/17 17 X 8 + 25 front and 17 x 9 +35 rear. THAT WAY YOUR SPEEDO SHOWS THE CORRECT SPEED ALS OJUST ASK YOUR LOCAL TYRE SHOP TO MATCH THE 16" ROLLING CIRFUMFERANCE TO YOUR NEW TYRES THEN U WILL BE OK

:D

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • The 296mm rotors are the R33 turbo brakes. The 310mm rotors are the R34 turbo brakes. The calipers are nearly the same, but not. They're the same caliper but the R34 caliper has longer legs so that it sits out far enough to go over the rotor. The pads are the same for both. When you say, "I bough tsome EBC"....did you just mean pads? Or rotors? 310mm rotors fit under 17" wheels. There may be some wheels without enough clearance though. I can't fit my fingers between the barrel of my wheel and the "corners" of my R34 calipers, but there is plenty of room behind the spokes. This is on Enkei RPF1. You can fit 324mm rotors inside a 17" wheel, but I'd be willing to bet that it would be close to impossible with the Nissan/Sumitomo caliper (using an adapter, of course), because the Sumitomo caliper is fatter than the Brembo caliper that is supposed to go on the 324mm rotors.
    • Hi. Can someone tell me what brakes(and mainly WHERE) can i buy brakes on R34 GTT? I bought some EBC which SHOULD go on my car(i have GT but it has GTT brakes) but it does not fit, Brakes are "too" small(296mm) Are 310mm be good or? I have 17 inch wheel so no "big boys" but for me driving i just need one that fits and i can get here in EU/Czech.
    • Since winter isn't that harsh anymore in Poland, i will definetely drive it 365 days a year 😉. But if the snow hits i will try it for sure and let U know. Only swap i am planning to do is of course R34 GTR front 😍.
    • Hey. Very valuable information about pitwork, I will pay attention when buying any consumable parts 🙏 As for the carpets - I got a handful of information from nengun, from which it appears that indeed the carpets for the driver's side are OEM. They are not able to show me any pictures due to the long chain of different sales entities but after I place the order, as soon as the goods arrive at the nengun warehouse from which they will send the shipment to me they can send me photos and if my purchase differs from OEM I can immediately return it / cancel the purchase. I think I will give it a try 😉. Of course i'll let you know what's what as soon as i get them P.s. I know the topic is not relevant to the thread, but both nengun and amayama have these SICK 😍 trunk room lamps available. Do you know anyone who ordered them? I need to have one in my car
    • I've managed to find this: Nissan_Stagea_AutechVersion260RS (1).pdf
×
×
  • Create New...