Jump to content
SAU Community

Wrecking Fully Worked R33 Gtst

wildr33gtst
 Share

Recommended Posts

wildr33gtst Rising Star

wildr33gtst

Posted
Posted (edited)

Hi unfortunately Just after finishing my project Not even being able to drive it 500kms before the unthinkable happened and my car was written off got hit in the Rear End by someone who obviously cant drive. The car owes me well over $50000 I have receipts for all the work and parts i have purchased for it most of the parts were bought directly from Japan. All top of the range japanese parts have been put on this car and the engine is still brand new not even 500kms like i said. I'm stripping everything from interior to motor to panels everything must go selling everything cheap and basically every part in brand new or hardly used. And as i said i have receipts for most of it.

Engine Parts include:

Fully bored and crack tested block with Arias Pistons and Rev conrods

The head has been ported and polished.

It has a Garrett GT3540r Turbo with .82 Exhaust housing with a Hi Mount Manifold which inludes

Oil and Water lines with a PSR wastegate plumbed back into custom V band dumpipe in Which JPC did a fantastic job of making it look factory. This Setup alone cost me in excess of $4000 with out labour All parts i have receipts for and done less that 500kms as my motor was still being run in so everything is in mint condition.

I have Denso 550cc Injectors with an Bosch 044 fuel pump and Sard Fuel Regulator.

Genuine Greddy plenum with Ford XF Throttle body including piping.

Os Giken Cam Gears Gates timing belt

Link Ecu with Hand Controller

2 Way Diff

Manual Gearbox with basically a brand new xtreme heavy duty clutch.

Bilstein Height and Damper adjustable coil overs

black Chrome 18 inch Rims with good tread

Everything i Have put alot into this car and has been modified to make big power was looking at making at least 360rwkw was making 330rwkw on my old setup before motor was built and new turbo etc was put on.

These are just the parts i can think about on top of my head there is plenty more.

I also have a Trust Front bar and nice trust sideskirts clear indicators

The interior is A1 and series 2 i need everything gone.

Going to take motor out this weekend and gearbox etc.

Will post up prices in the next couple of days if anyone needs any parts just let me know and i will take it off for you. I have lost an absolute fortune on this car and whats my loss is your gain just need it all gone makes me to depressed looking at it knowing how much i have put into it.

cheers

Edited by wildr33gtst
Link to comment
https://www.sau.com.au/forums/topic/225450-wrecking-fully-worked-r33-gtst/
Share on other sites
  • Replies 49
  • Created
  • Last Reply

Top Posters In This Topic

Popular Days

Top Posters In This Topic

Popular Days

Posted Images

wildr33gtst Rising Star

wildr33gtst

Posted
  • Author
Posted

will put up some prices when i go home im located in bentleigh. Will be home in an couple of hours 2 reply 2 everyones messages and posts. Cheers

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • GTSBoy
      NC MX5

      By GTSBoy · Posted

      My thought is if you were just moving it forward and the upstream geometry remained the same, then no difference at all. But because the current one has the filter direct into the AFM inlet, you effectively have the best chance of a completely symmetric air flow profile upstream, and in, the AFM, whilst the aftermarket inlet thingo has a (small, to be sure) bend between the filter and the AFM. That would bias the flow to the outside of the bend (downstream of the bend) which might well reduce the size of the signal seen by the AFM, for the same total flow rate. Having said that: If you're proposing to make your inlet look like a hybrid of your existing one and the aftermarket one, such that there is no bend where the filter is clamped on... then I say it will be just fine. If there is going to be such a bend, then, if you can align the insertion of the AFM blade such that it is at right angles to the plane of the bend, then there is a better than even chance that the centreline velocity where the blade is will remain more or less the same, and the velocity will just be a little faster to the outside of that, and just a little slower to the inside. **This is not professional investment advice and you should consult a suitably qualified ouija board, tea leaves or the intestines of a goat for more accurate prognostication.
    • pacman_1219
      Blue/grey smoke after idle

      By pacman_1219 · Posted

      Hi Tao, Thanks for your reply.  It's been a while and I managed to get the valve stem seals replaced with the head on the car.  Unfortunately this didn't solve my issue, the car still smokes a lot after idling (to be honest during idle you can see a bit of blue smoke from the exhaust), same after deceleration. I will try disconnecting the valve cover breathers, do I leave the PCV valve in? By engine oil drain pipe, do you mean the turbo oil drain?
    • GTSBoy
      Nissan fuga 450gt android screen

      By GTSBoy · Posted

      What about if you just give it direct 12v and earth?
    • The king 2.0
      Nissan fuga 450gt android screen

      By The king 2.0 · Posted

      Hi guys . Can someone help me  I bought an Android screen for my Nissan fuga but it won't turn on   
    • MBS206
      NC MX5

      By MBS206 · Posted

      My guesstimate, with no real numbers to back it up, is it won't effect it greatly at all.its not a huge change in position, and I can't see the air flow changing from in turbulence that much based on distance, and what's in front of it. Johnny and Brad may have some more numbers to share from experience though.
×
×
  • Create New...