Jump to content
SAU Community

Recommended Posts

  • Replies 55
  • Created
  • Last Reply

Top Posters In This Topic

Well i just went on the new Eastlink. Not bad

I had a good run i was the only car in the tunnel. Well worth seeing at night guys...

And as for that motel thing...Well i dont know.. Im guessing some kind ot control tower..

Only saw 1 cop car(van) at the Frankston end heading back towards the city....

Superfluous art work is such a wank...personally I'd rather look at an empty paddock and have cheaper tolls.

Seriously I like roads to be roads not "conceptual experiences" what a waste of $$ and we're all paying for the privilege of admiring it.

Fancy bridges-tunnels, hotels to nowhere, ect Grrrrrrr.

A lasting legacy of how we were all Bracks'd.

Nice Toll road though, It's just a shame it's not the freeway we've all waited 30+yrs for. :D

Edited by madbung
All they need now is a popsicle stick skyscraper, giant magnifying glass, and the escalator to nowhere!

MONORAIL!

Gold!!! can I drive?

Whoever tags that "hotel" first I hope they do a Homer in one of the windows trying to get out.

Tried to get from one part of the suburb to the other this arvo and traffic was banked back till the flinders turn off. With all those eastern wombats queing across the intersections it was frustrating to say the least.

It was worse than boxing day traffic and thats saying something...now who was that idiot who scrapped the bypass?

GO HOME EVERYONE!! there's nothing for you here :(

Edited by madbung
people say the cameras dont work for the first month, but by all means you go first and speed through :( not worth the risk imo
Too late. Some idiot P-plater already been done - 135kph in 100 zone.

After all the publicity, it would seem some are just too f*****g stupid to have a licence.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Which solenoid? Why was it changed? Again, why was this done? ...well, these wear..but ultimately, why was it changed? Did you reset the idle voltage level after fitment? I'm just a tad confused ~ the flash code doesn't allude to these items being faulty, so in my mind the only reason to change these things, would be some drive-ability issue....and if that's the case, what was the problem? Those questions aside, check if the dropping resistor is OK ...should be 11~14 ohms (TCU doesn't throw a flash code for this) ~ also, these TCU designs have full time power (to keep fault code RAM alive), and I think that'll throw a logic code (as opposed to the 10 hardware codes), if that power is missing (or the ram has gone bad in the TCU, which you can check..but that's another story here perhaps).
    • Question for people who "know stuff" I am looking at doing the new intake like the one in the picture (the pictured is designed for the OEM TB and intake plenum), this design has the filter behind the front bar, but, the filter sits where the OEM duct heads into the front bar, and the standard aperture when the OEM ducting is removed allows the filter to pulled back out of the front bar into the engine bay for servicing, a simple blanking plate is used to seal the aperture behind the filter This will require a 45° silicone hose from the TB, like the alloy pipe that is currently there, to another 45° silicone hose to get a straight run to the aperture in the front bar Question: how will it effect the tune if I move the MAF about 100-150mm forward, the red is around where my MAF is currently, and the green would be where it would end up Like this This is the hole the filter goes through  Ends up like this LOL..Cheers    
    • Despite the level up question, actually I do know what that is....it is a pressure sender wire.  So check out around the oil filter for an oil pressure sender, or maybe fuel pressure near the filter or on the engine. Possibly but less likely coolant pressure sensor because they tend to be combined temp/pressure senders if you have one. Could also be brake pressure (in a brake line somewhere pre ABS) but maybe I'm the only one that has that on a skyline.
    • Pull codes via the self-diagnosis procedure. As far as I can tell this is just a sign of transmission issues but not a code unto itself.
    • Hi All, putting the engine back together and everything is perfect except have this plug left over.. any ideas what it is for and where it goes? Is on cold side under the intake plenum *note not a stock plug, as everything has been modified Cheers
×
×
  • Create New...