Jump to content
SAU Community

Recommended Posts

Hi Guys/Gals,

i have a BNR34 RB26DETT, just recently my work machanic serviced my car and he put in NGK Platinum spark plugs after that the car started to misfire bad :D . i put NGK Iridium plugs back in and the misfire is a little better but it's still there. now it's getting worse and worse the car is splattering and when i accelertate car just splaters and doesn't go anywhere. would a retune fix this or is it deeper than that. any help and suggestion would be greatly appriciated.

Link to comment
https://www.sau.com.au/forums/topic/226088-engine-is-fd/
Share on other sites

Coppers for the win at around .8mm gap

Check all the plugs are clicked in

Check that the contacters in the bottom of the coil packs are still there i had a set floating around the floor of my car put them in and was missing found the contacter on the floor put in back in and is good you will have to remove the rubber boot to find them also while your there give them a clean with some fine emeroy paper

If that all fails swap over coils and air flow meters only do one at a time to find out which is f**ked

Link to comment
https://www.sau.com.au/forums/topic/226088-engine-is-fd/#findComment-3983011
Share on other sites

Bit early for R34 coil packs to be failing.

Does it have an aftermarket ecu. If so id say it needs a retune and some fresh copper plugs.

Two words Race Pace

Racepace is were i got my stage1 done and were i normally get my car serviced. the 1 time i didn't take it there this happens. anywayz tried to book but Ben said he's busy for 2 weeks.

Link to comment
https://www.sau.com.au/forums/topic/226088-engine-is-fd/#findComment-3985989
Share on other sites

so is it constantly or just under boost?

constant. when engine is cold it's misfire is really really bad but once it's working temp it's kind of ok (but still there). must be foul on plugs until high temp burns most of it away hence ok when warm. what do u guys/gals think?

Link to comment
https://www.sau.com.au/forums/topic/226088-engine-is-fd/#findComment-3986292
Share on other sites

yeah loose plug then, check the coilpack loom and all plugs, even unplug and replug them all

if the coils were old and tired it would misfire on boost but be ok for normal load

if the gap was wrong it would be fine for normal load only on boost it would misfire

Link to comment
https://www.sau.com.au/forums/topic/226088-engine-is-fd/#findComment-3986303
Share on other sites

ok...thats the answer i been waiting for.....what i reckon is wrong is that the connector prong to the coil on misfiring cylinder isnt fitted into the connector properly ive done it myself....what you do is let the car idle and disconnect each coil connector until you find the one that doesnt make a diffrence and theres your culprit

Link to comment
https://www.sau.com.au/forums/topic/226088-engine-is-fd/#findComment-3986933
Share on other sites

I just got my car back from the mechanic with the same problem. What the problem was, the coil pack wire was shorting out and caused the car to misfire like hell. He replaced the sparks (copper ones gapped to .8) due to them fouling up and changed the coil pack wire. Car is 100% better.

Link to comment
https://www.sau.com.au/forums/topic/226088-engine-is-fd/#findComment-3989955
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • The wideband reading is meaningless if it's not running. Why are you using shitty old sidefeeds on any engine, let alone a Neo? What manifold and fuel rail are you using to achieve that? Beyond that, can't help you with AEM stuff as I've never been their ECU/CAS combo.
    • Manual boost controllers (where a little of the boost was bled off) were quite common back in the day, because they were cheap and easy. Generally they had a manual adjustment screw rather than being fixed like yours. Down side is they always bleed boost, not just when you want them to so an electronic boost controller that uses a solenoid will have less lag.
    • Hello , im new here and i have A31 home build  RB25det neo stock eng / turbo  aem ems 2 blue connector  aem 3.5 map aem cas disk aem wideband connected to ecu  355 lph pump 550 nismo yellow injectors side feed aftermarket regulator  and won’t start with base aem tuner basic tune eventually flipped cas 180 degree so it triggers on correct stroke not in exhaust cycle  Now it won’t start Wideband reads 10 and 11 at lowest fuel setting  and will share calibrations soon for aem tuner i think something is wrong in aem tuner    please if you have any information, am very grateful         
    • Legend. I ended up finding the facebook account of the owner of the first car i sent but sadly he deactivated the account. I think you’re right in saying it’s some sort of well done custom job. Really appreciate your help anyways.
    • Totally equivalent. Stock often goes from the comp cover because that's where the actuator is also installed and the factory needs 2" of hose to make the connection - and it comes as a pre-assembled unit. They totally have a boost reference from somewhere between the turbo and the throttle(s). Oh, jeez. Just do it in M12 then. We don't actually care that much. I would expect any such AN converter fitting to rely on an o-ring or some other seal onto a flat surface under the flange of the hex**, because bolt threads are no intended to provide a pressure seal. unlike..... pipe threads. **which also requires a suitably flat and smooth surface on the turbo's boss to provide the seal.
×
×
  • Create New...