Jump to content
SAU Community

Recommended Posts

nice painting skills.

but i think it looks a bit weird the way the black comes so close to the front wheel, and cuts in at the headlight half way.

would have looked better on a slant, with the whole front in black, including black front bar.

sort of like this

post-29392-1215263419_thumb.jpg

Edited by Munkyb0y
  • Replies 67
  • Created
  • Last Reply

Top Posters In This Topic

Top Posters In This Topic

Posted Images

I like it cause its different. every skyline looks the same where i live either 1 of 4 colours white,grey,black,silver. so i did mine up to be different if everyone did there cars up the same we wouldn't be on the SAU forum it'd be the HSV owners club(no offence guys)

Edited by yup21t

It's good that you like it.

it's your car.

You were after opinions..

I just think the black comes down too far.

and it makes it look as though it wasn't thought out very well (to me!).

I don't mind cars which are 2 toned with a massive range of colours.. even those ugly gold and brown silvia's look ok sometimes.

but this black comes down too far I think.

As someone mentioned earlier, if it had stopped at the bonnet/top of the guards level, it would have looked great.

Mine is painted Westinghouse white from factory and I think it looks better than that combo you've done.

Having said that, I like both the black or the candy red you used, but on their own. not in that design.

Geez so much hate...

It's your car man, if you like how it turned out then f**k what the rest of the people here think.

I like it, not my idea of PERFECT but it's very different, at least you're not the same as every other man and his dog.

why is it so important to be different than everyone else?

I don't get the obsession.

Why the fark do you want to be the same?????? :(

Fark, it will be a boring place if we all did the same things, had the same opinions, drive the same cars, had the same colour/mods/power/handling/etc/etc/etc.............................

true thanks heaps. i chose to be different because when you go to a show or an event there's nothing worse than seeing the same car over and over. i posted these photo's just to see how it would be viewed by other people and and alot of you like it and alot of you dont and thats cool. but if it bothers you that much and it's (yuck,worst you've seen) looks like shit or what ever just think you dont own it and you dont have to live with it. if its that bad please SAU delete this thread and my apologize if i offended all the skyline owners of australia.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • So for the wide band is a Bosch 4.9 correct for the Link G4+ along with a Can bus? Just get the Link gear or is generic ok too? Eg here: LINK LINK DIGITAL WIDEBAND CAN MODULE WITH BOSCH 4.9 SENSOR : KYP Performance House  
    • Bit difficult to follow. Have a look below and see what the standard R32 layout was like. Note there was a restrictor in place immediately before "turbocharged pressure control solenoid" that, if removed, magically got you 1 bar boost.
    • I might be way off the mark here.. there must be a T junction under the manifold. That takes manifold pressure through a check valve prior to the T, one side splits out to this bleed off orifice, the other straight to the wastegate actuators. 
    • Carrying out some engine due diligence before my first drive in a 260RS that has been in storage for 10+ years, and found two lines that are susposed to be plumbed into the boost control solenoid. One of the lines (the wastegate boost supply line) to actuate the gates, had a bolt in one end blocking it. The other line (main boost signal line) from the very rear of the intake manifold (RB26DETT) and runs up to the boost controller had this pill in the end of it as seen in photos. Other than the obvious (T28 Ceramic turbos might well be cooked)  Can anyone shed any light on if there is any validity at all with this mod, bleeding a constant fixed rate of manifold boost pressure off through this 3mm hole?  Is it deliberate?  Was this a 90s Jap mod done to RB26's? Or has someone just fitted this without any idea of what happens to ceramic T28s if they are not gate controlled?    
×
×
  • Create New...