Jump to content
SAU Community

Recommended Posts

  • Replies 244
  • Created
  • Last Reply

Top Posters In This Topic

ill give him full credit once its tuned and running properly... its only idling and light revs atm lol

dont let it idle for too long...id keep it shut down now until you can give it some decent revs with the engine loaded up as this will help the rings to bed properly. Then feed it some boost!!

http://www.mototuneusa.com/break_in_secrets.htm

I know its hard to have it sit there and not drive it, but you should only turn key when you are ready to drive/tune it. It will give the engine the best possible chance to bed everything in.

http://www.mototuneusa.com/break_in_secrets.htm

I know its hard to have it sit there and not drive it, but you should only turn key when you are ready to drive/tune it. It will give the engine the best possible chance to bed everything in.

that link is how i like to do things...don't baby them...run them hard to give them every possible chance.

  • 2 months later...
hows the update going with this?

any final power figures?

don't quote me but i think it was making boost at 3000rpm and full boost at 4100rpm...they got to 530hp before the dyno shat itself. Ill get Simon to post when proper info comes to hand.

  • 4 weeks later...

first proper dyno sheet 22p 536.3hp at only 7500 start to die off im gonna put it down to the size of the ex housing .81 single entry

he still hasnt touched the cam gear still set at 0 both sides and he said he still hasnt started looking for power. still conservative nearly 550ks to a tank so im pretty happy with it....

response for the size turbo it is is quite insane aswell neways have a gander

post-7443-1253941219_thumb.jpg

yeh ur rite file size is huge lol.... and no its not a run in tune.... thats basically a half done proper tune i had sum minor boost leaks to fix b4 he would push it ne further...... and wen i got back afta tightening a few t bolt clamps etc the dyno had magically arsed itself.... i waited 4 days in total to get the car redone only to try a sidestep of the clutch in 3rd and lets just say we found the weak point.... believe this or not but a hks gd max twin plate slipped b4 the gbox let go..... so yeh i wasted those four days down in brisbane for nuthin. im abit down for cash atm so thats the tune its gettin for the moment until the clutch is done. still tho 402rwkw is still nuthin to snuff ya nose at....

400rwkw is a good number dont get me wrong, but its only 46hp more than my 25 at basically the same boost level with a GT30. Granted im running E85.

I would have though an RB28 with big cams and a T04Z would be making a little more than that, maybe im wrong.

like i said theres still not finished.... havent touched cam gears at all 20p still 5 pound to go and also havent started pushing the timing at all yet its still very conservative. and yes e85 is good shit so ive heard im only on bp ultimate because thats all i can get..... and yeh i wasnt exactly happy with the first figure either but hey its a start and im going from there

Edited by skylinekid

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Depending on how long the car sat it is very possible for injectors to be stuck open or closed, I'd get them cleaned and flow tested. Other than that, obviously when the loom changes and the car doesn't start any more....the loom is suspect so some tracing / comparing may be required
    • Harness is for a s1 Rb25det, and it is engine and lower harness.  the old harness had broken off plugs and was in very rough condition/exposed wires and splices etc. it is not able to be put back on the car, I could visually inspect to see if they had rewired any pins on the ecu plug. The fuel pump definitly isn’t turning off it’s an external pump and very loud you can hear it. Will look at the other harness tonight, am also going to pull the fuel rail and watch the injectors spray, will update here with what I find. Pretty sure at this point it has to be something to do with injectors because car will fire up on starting fluid and cas is clicking the Injectors. Fuel pressure is steady 43psi 
    • Check the injectors flow evenly, and are actually flowing what you and the ECU think they should be flowing. If it's starting up on starter fluid, you have a fuel issue. Is it possible under cranking your fuel pump is turning off?   The harness you replaced, is that the whole engine harness? Do yourself a test, and drop the old harness on and plug it into the Z32 ECU. It's possible they've wired things different. From memory S1 to S2 is different in RB25 and you may have a wrong loom
    • I haven’t pulled the injectors to watch them spray yet but they are clicking from the cas and all of the spark plugs are wet with fuel. I’ve thought the cylinders were being flooded from the beginning and was hoping fuel pressure would fix it. Tonight I am going to pull the rail and watch the injectors spray. Don’t know how to test/diagnose if the plugs are firing in correct sequence but that should be a timing thing and as far as timing goes my car still has the half moon for the cas can only install it 1 way. And my mechanical timing is 100% correct I posted photos above. Confirmed with the balancer on and off. 
×
×
  • Create New...