Jump to content
SAU Community

Recommended Posts

Hey guys,

Well, it's 5,000 after my I bought my Skyline so time to change the oil. (and yes, I should have done it as soon as I bought it, I know...) I haven't had a Skyline before, and my previous two cars have been a magna and a HQ, so I'm used to something that I can just do whatever to and it'll be fine. So if you can bear with me and offer any helpful comments that'd be great!

So Saturday morning was spent reading through the 42 pages of the 'good oil' DIY thread, and the oil change tutorial and whilst I then had a good idea as to how to do it and how much things cost, not so much on what oil was a definite answer to run with.

I've got a stock R33 Series 2 GTS-T, with 93,000 on the clock, so I decided against any 0w oil, and bought 5ltr of Motul 8100 5w40. The general consenus on the oil thread seemed to be running at either a 0w or a 5w oil, but 0w sounded a little too thin. The autobahn assistant recommended a 10w for it, but I thought that may be a little too heavy, so went with the 5w. So, question to you guys is, what do you run in yours?

The oil that was in it from the shop was a lot thicker than the oil that I put in. I've always had the feeling that the motor wasn't as responsive as it should be and that it was being restrained under acceleration, where as after I put the 5w oil in, the difference is amazing. The engine feels so much smoother and more responsive than it did before, a blip of the throttle results with an instant rev, as opposed to a slightly delayed and sluggish rev. So it feels like it was a good choice. However now I can hear some noise from the tappets that I didn't notice before, it's only when you've got your head in the engine bay can you hear it, it's not so loud that you hear it with the bonnet down, but is this normal for an engine of this age?

Currently oil pressure at idle is a bit over the 2kg/mm^2 mark, and sits at dead horizontal at about 70/80kmh so at about 4kg/mm^2, are these normal values?

Thanks in advance for any help guys, oh, and also, does anyone know any places to recommend/avoid for my 100,000 service? And a idea of the cost?

Cheers,

Link to comment
https://www.sau.com.au/forums/topic/228024-oil-change-sanity-check/
Share on other sites

i used mobil 1 but now i'm using nulon 10/40 i think! both are fully synthetic and i like the nulon because it's quiet!

but if you're looking for someone to do the 100k service there are some people who can do it on here but if you want a workshop go to boostworx!

Royal Purple 10w 40! Good Stuff :laugh: Used to have a slight tapping noise with the Mobil 1 0w 40 but has seemed to quieten down a bit since the new gear has gone in. Has just been changed so i'll let you know if it comes back after 5,000km's.

Edited by SLEEPR85

i am going to be doing my oil change and all this weekend and i always use fully synthetic 10w 40 specially this time of the year....

your tappet noise theory could be the tappets or injectors as steve said......get a mechanic that knows his stuff to check it out

Quiet oil?

Thick oil is quieter, an old trick to use when selling a car with an old motor was to use the thickest oil possible to reduce smoke and quieten tappets and assorted noises.

A bannana skin or stocking in the diff made it quieter.

A raw egg in the radiator fixed leaks or (or ground pepper to fix a cracked head)

A quick steam clean to hide the old leaks and you can ask an additional 1k for the car.

Thick oil is quieter, an old trick to use when selling a car with an old motor was to use the thickest oil possible to reduce smoke and quieten tappets and assorted noises.

A bannana skin or stocking in the diff made it quieter.

A raw egg in the radiator fixed leaks or (or ground pepper to fix a cracked head)

A quick steam clean to hide the old leaks and you can ask an additional 1k for the car.

So how is it you know these things? :laugh: Haven't been a used car salesman in the past?

So how is it you know these things? :( Haven't been a used car salesman in the past?

You spend time in workshops and you come accross all sorts of things.

Some of the fixes above are also useful for the bush mechanic, when parts aren't available you have to improvise. I can also fix a flat tyre with spinifex, and recharge a battery with urine. :)

great choice in oil buddy 8100 is good! ive ran a few before fuchs/torco dont notice a big difference really but i run motul fluids throughout!

while car is running grab a large screwdriver put the handle to your ear and then touch the other end ontop of engine (like on the cam cover then on the inj rail) slowly move around this will allow you to find the ticking noise easier

Thanks for the replies guys, I'm just concerned that the oil that I've got in there is too thin. But the engine seems to be loving it as it revs so much easier and is much more responsive.

The ticking noise seems to be coming from the underneath the valve cover which is why I was thinking it was from the valve train. I didn't notice it before which is why I was thinking it was the oil.

What're the standard oil pressures that the car should be operating at? My seems to sit on over 2kg/cm^2 at Idle and up around 4 when driving, (however yesterday afternoon it was idleing below two, and only just over when driving, which had me very worried, however it's still full of oil and hasn't done that since.. so I've got no idea what it was doing then...)

Thick oil is quieter, an old trick to use when selling a car with an old motor was to use the thickest oil possible to reduce smoke and quieten tappets and assorted noises.

A bannana skin or stocking in the diff made it quieter.

A raw egg in the radiator fixed leaks or (or ground pepper to fix a cracked head)

A quick steam clean to hide the old leaks and you can ask an additional 1k for the car.

hmmm, eggs, bananas, & pepper.........sounds like a good recipe for a protein shake.

Save you the trouble though, just run 80W90 in the sump.......that'll eventually make the engine so quiet that you won't hear it.....only the sound of wind & smell of diesel from the flat bed truck you & your car are sitting on, lol

i use motul 300v 15w50, i use thicker oil because i have a rebuilt rb25 with forged pistons.

my oil pressure sits on 2 bar at idle too, & i also get a fair bit of tappet noise. the tappet noise started after the engine build and only occurs on idle when fully warmed up. its something i would like to get fixed at some point, although im not sure what would be involved?

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Who did you have do the installation? I actually know someone who is VERY familiar with the AVS gear. The main point of contact though would be your installer.   Where are you based in NZ?
    • Look, realistically, those are some fairly chunky connectors and wires so it is a reasonably fair bet that that loom was involved in the redirection of the fuel pump and/or ECU/ignition power for the immobiliser. It's also fair to be that the new immobiliser is essentially the same thing as the old one, and so it probably needs the same stuff done to make it do what it has to do. Given that you are talking about a car that no-one else here is familiar with (I mean your exact car) and an alarm that I've never heard of before and so probably not many others are familiar with, and that some wire monkey has been messing with it out of our sight, it seems reasonable that the wire monkey should be fixing this.
    • Wheel alignment immediately. Not "when I get around to it". And further to what Duncan said - you cannot just put camber arms on and shorten them. You will introduce bump steer far in excess of what the car had with stock arms. You need adjustable tension arms and they need to be shortened also. The simplest approach is to shorten them the same % as the stock ones. This will not be correct or optimal, but it will be better than any other guess. The correct way to set the lengths of both arms is to use a properly built/set up bump steer gauge and trial and error the adjustments until you hit the camber you need and want and have minimum bump steer in the range of motion that the wheel is expected to travel. And what Duncan said about toe is also very true. And you cannot change the camber arm without also affecting toe. So when you have adjustable arms on the back of a Skyline, the car either needs to go to a talented wheel aligner (not your local tyre shop dropout), or you need to be able to do this stuff yourself at home. Guess which approach I have taken? I have built my own gear for camber, toe and bump steer measurement and I do all this on the flattest bit of concrete I have, with some shims under the tyres on one side to level the car.
    • Thought I would get some advice from others on this situation.    Relevant info: R33 GTS25t Link G4x ECU Walbro 255LPH w/ OEM FP Relay (No relay mod) Scenario: I accidentally messed up my old AVS S5 (rev.1) at the start of the year and the cars been immobilised. Also the siren BBU has completely failed; so I decided to upgrade it.  I got a newer AVS S5 (rev.2?) installed on Friday. The guy removed the old one and its immobilisers. Tried to start it; the car cranks but doesnt start.  The new one was installed and all the alarm functions seem to be working as they should; still wouldn't start Went to bed; got up on Friday morning and decided to have a look into the no start problem. Found the car completely dead.  Charged the battery; plugged it back in and found the brake lights were stuck on.  Unplugging the brake pedal switch the lights turn off. Plug it back in and theyre stuck on again. I tested the switch (continuity test and resistance); all looks good (0-1kohm).  On talking to AVS; found its because of the rubber stopper on the brake pedal; sure enough the middle of it is missing so have ordered a new one. One of those wear items; which was confusing what was going on However when I try unplugging the STOP Light fuses (under the dash and under the hood) the brake light still stays on. Should those fuses not cut the brake light circuit?  I then checked the ECU; FP Speed Error.  Testing the pump again; I can hear the relay clicking every time I switch it to ON. I unplugged the pump and put the multimeter across the plug. No continuity; im seeing 0.6V (ECU signal?) and when it switches the relay I think its like 20mA or 200mA). Not seeing 12.4V / 7-9A. As far as I know; the Fuel Pump was wired through one of the immobiliser relays on the old alarm.  He pulled some thick gauged harness out with the old alarm wiring; which looks to me like it was to bridge connections into the immobilisers? Before it got immobilised it was running just fine.  Im at a loss to why the FP is getting no voltage; I thought maybe the FP was faulty (even though I havent even done 50km on the new pump) but no voltage at the harness plug.  Questions: Could it be he didnt reconnect the fuel pump when testing it after the old alarm removal (before installing the new alarm)?  Is this a case of bridging to the brake lights instead of the fuel pump circuit? It's a bit beyond me as I dont do a lot with electrical; so have tried my best to diagnose what I think seems to make sense.  Seeking advice if theres for sure an issue with the alarm install to get him back here; or if I do infact, need an auto electrician to diagnose it. 
    • Then, shorten them by 1cm, drop the car back down and have a visual look (or even better, use a spirit level across the wheel to see if you have less camber than before. You still want something like 1.5 for road use. Alternatively, if you have adjustable rear ride height (I assume you do if you have extreme camber wear), raise the suspension back to standard height until you can get it all aligned properly. Finally, keep in mind that wear on the inside of the tyre can be for incorrect toe, not just camber
×
×
  • Create New...