Jump to content
SAU Community

Recommended Posts

Seems to me that there are some tight arses on here that want to save a couple of dollars everytime they fill up instead of spending the couple of dollars and preventing the massive bill of 5 grand plus to rebuild their engines.

Japanese fuel has higher octane ratings than we have here so the least you should be putting into your cars are 98. If you cant afford the fuel you shouldnt have bought the car.

ive used 95 octane once and instantly felt the difference, never went back to 95, always use 98 and it is literally only a couple of dollars extra for the whole tank to be on 98 instead of 95 so ive always used the 98 since..... i doubt one tank of 95 will do any damage at all, and they are set to run at 95 minimum, not 98 but nissan recommends 98 or higher, but 95 is acceptable..... but up to you if you wanna risk saving a total of $100 ish in fuel costs only to have to rebuild an engine.....

i'm a tight ass so i choose to spend the extra $100 a year on decent fuel

You noticed a difference between 95 and 98 because it would have been pinging and the ecu would have pulled timing and possibly dumped a little fuel in.

100% and I mean 100% stock car and 95ron is fine.

Drop an exhaust on it and you need 98 otherwise it will be pinging.

When i was running stock boost i ran 95 and its fine!!!!! Now that its been tuned for 98 i only run 98 (remap ecu) but the other day my mrs fillied it up with 95 :P The ecu automatically pulled a heap of timing and it was fine (still went well). Just used it all up and filled it back with 98 and all good. Cant comment on a power fc though.

Just a pitty the ECU stops listening to the det sensors past ~5000rpm. So no protection and BANG there goes a ring land. :P

The PFC. There's no ign retard but the dash light flashes at you letting you know some things up. Then you trim out a few degree's and your fine until the next batch of fuel.

When I was pushing the stock turbo near its limits I found 95ron I had to pull out ~5degree's. 91-92ron was 8-9degree's. So way too much.

Std ecu, stock boost, stock exhaust 95 ron was ok. 2degree's advance had it pinging. 98ron I was able to push in 5degree's and with everything stock it picked up a healthy 10rwkw which is not too bad considering its just a turn of the crank angle sensor. :D

When pouring Octane Boost or Toluene to raise RON, it's best to wear a latex glove, so that none of it gets on your skin.

$2 shops have them pretty cheap.

They're carcinogenic and it absorbs through the pores.

(Sure a charred steak is also carcinogenic but some toxins are riskier than others).

Tez (also a pharmacist) :)

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I was 99% sure the standard one is long enough to get there, you might just have to change the throttle orientation. If not, I remember someone having used an r31 cable instead, but that is probably harder to find than r33 by now...
    • HELP   Hey all, Is there an accelerator cable from another Nissan that can be used on the R33 GTST RB25DET with a Greddy forward facing plenum?  Thanks in advance  Rob 
    • Or do we think it was installed to give 1 bar of boost max, all day, everyday?
    • So could it be assumed it has been installed intentionally with potentially a power FC boost controller kit? 
    • Had my rig on Matt's dyno at PITS the other day. After a few years between tunes I added a few sensors and swapped intercoolers. Result. 553hp at 26psi. Not bad for an FJ20 that was built in 2007. The problem.. It filled the overflow bottle on hard runs which leads me to believe the head gasket isn't sealing. I have a coolant pressure sensor which was reading cap pressure at 22psi and occasionally overrunning to 23/24 psi on deceleration after a pull. It was not spiking. It has arp2000 head studs and a cometic gasket. As its been 18 years in service, I pulled the engine out and head off. Everything looks good but we obviously have an issue. Where I'm at.. Years ago I had the same issue, I checked the stud tension and they were all over the place. Some at 60 to 70 and some up near 90. I nipped them all to 100ft lbs and this stopped the water push until now. I believe this compromised the gasket back then. What do I do? 2 options are..  1) I bought arp 625+s, which I could put in with a new gasket. Thinking Kameari this time, reassemble and try again. 2) strip the block, get fire rings machined in with copper gasket and try that. I do not want to push it more than 28 to 30psi. I think the turbo will be out by then anyway. (G30-770). My other concern is the long term ability of a copper head gasket. Are they streetable for years? I feel like a new gasket with the new studs will probably suffice, but I don't know. Any thoughts welcome and advice on copper gaskets and fire rings. Thanks!
×
×
  • Create New...