Jump to content
SAU Community

Recommended Posts

hey all

i haf a 94 r33 Gts...and i fill up on bp ultimate...

the prob is...even when my car runs around 430kms already on a full tank and the needle is just touchingt the line at e...

no warning light comes up?

it freaks me out cause then i dont know how much ic an push it

is there a warning lightand WHEN is it supposed to come out?

Link to comment
https://www.sau.com.au/forums/topic/22914-low-fuel-warning-guage/
Share on other sites

It could also be that the light is broken, but not very likely

If its really a concern, just go crusing when you are close to empty again, with a friend in their car.

I remember the first time my light came on, I had my car about 6 months and it really confused me having never seen it before.

My best effort is 80km from first fuel light coming on.

Streamer, how many L are you putting in when you fill up?

hmm...not sure...but if i drive till around where the E line is, the needle EXACTLY on the line at the E...yet no light,

i can fill up to around 50 bucks.

with around 98c per litre.

i can go for close to 480ks driving like a nana...if not then its around 420.

why?

i have seen the light only twice now having owned the car for a year, i didnt think it had one for a long time till i decided to forget to fill up and sure enough on it came and scarfed the **** outa me, so off to the servo i went.....

Well, the R33 has a 65L fuel tank, and if you are only putting in $50 at around 98c, you're only putting in just over 50L. You'd have nearly 100km worth of fuel left when you're currently filling up.

I can drive til my light comes on and get around 450 easily, mind you my car is still completely stock until next month, so this could be why.

what i meant is i fill up till the thing clicks and the tank is on the verge of overflowing...

mind u, 65l is prob frm the last drop...

i never even had e chance to see the light alto i might try this time cause my gas is low once again.

eveytime i try, i freak out.

so with the needle on the e line, i fill around 55...

so i guess it works out...

A fuel filter does indeed catch most of the impurities, but there is still a chance something can get through.

I had a car (carby) this happened to and it was well maintained, i let the fuel run down and the car died.

So a new carby, fuel pump and tank clean out later........

The problem was dirty fuel from the servo, and it was proven, i only ever ran premium in it!

Agreed, running on empty is not a good thing. Ive only had occasion to do it once.

The idea of running out of fuel anywhere is something Ill try to avoid.

All I was trying to say was that the fuel light will come on, and you still have time left. It is of course, a fuel warning light, hence, warning.

i saw the light today when parked on a slope.

went to uni

came back, backed out of the slope and there went the light.

safely say that i saw the light hence satisfied for now that there is a light and never worry abt stallin in the middle of the road again.

managed to get in 58l too...of bp ultimate today which means it is a 65l tank for sure.

i get around 450 - 470 if driving normally with the occasional lead footedness when the road is wet...like today in perth...YAY

only on private rds tho...

heh

laters

Speaking of guage, i haven't yet own a skyline, but looking at the R33 GTS25 does the radiator fans comes on straight away when you switch the engine on (i know it does when its warm obviously). And the temp guage goes up half way after like 5mins of driving it. Is this normal? If not wat seems to b the problem? Help!

Thanx guys!

  • 2 weeks later...
Originally posted by Phat^Beatz

Speaking of guage, i haven't yet own a skyline, but looking at the R33 GTS25 does the radiator fans comes on straight away when you switch the engine on (i know it does when its warm obviously). And the temp guage goes up half way after like 5mins of driving it. Is this normal? If not wat seems to b the problem? Help!

Thanx guys!

*Bump* Help! *Bump*:P

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • If as it's stalling, the fuel pressure rises, it's saying there's less vacuum in the intake manifold. This is pretty typical of an engine that is slowing down.   While typically is agree it sounds fuel related, it really sounds fuel/air mixture related. Since the whole system has been refurbished, including injectors, pump, etc, it's likely we've altered how well the system is delivering fuel. If someone before you has messed with the IACV because it needed fiddling with as the fuel system was dieing out, we need to readjust it back. Getting things back to factory spec everywhere, is what's going to help the entire system. So if it idles at 400rpm with no IACV, that needs raising. Getting factory air flow back to normal will help us get everything back in spec, and likely help chase down any other issues. Back on IACV, if the base idle (no IACV plugged in) is too far out, it's a lot harder for the ECU to control idle. The IACV duty cycle causes non linear variations in reality. When I've tuned the idle valves in the past, you need to keep it in a relatively narrow window on aftermarket ecus to stop them doing wild dances. It also means if your base idle is too low, the valve needs to open too much, and then the smallest % change ends up being a huge variation.
    • I guess one thing that might be wrong is the manifold pressure.  It is a constant -5.9 and never moves even under 100% throttle and load.  I would expect it to atleast go to 0 correct?  It's doing this with the OEM MAP as well as the ECU vacuum sensor. When trying to tune the base map under load the crosshairs only climb vertically with RPM, but always in the -5.9 column.
    • AHHHH gotchaa, I'll do that once I am home again. I tried doing the harness with the multimeter but it seems the car needed a jump, there was no power when it was in the "ON" position. Not sure if I should use car battery jump starter or if its because the stuff that has been disconnect the car just does send power.
    • As far as I can tell I have everything properly set in the Haltech software for engine size, injector data, all sensors seem to be reporting proper numbers.  If I change any injector details it doesnt run right.    Changing the base map is having the biggest change in response, im not sure how people are saying it doesnt really matter.  I'm guessing under normal conditions the ECU is able to self adjust and keep everything smooth.   Right now my best performance is happening by lowering the base map just enough to where the ECU us doing short term cut of about 45% to reach the target Lambda of 14.7.  That way when I start putting load on it still has high enough fuel map to not be so lean.  After 2500 rpm I raised the base map to what would be really rich at no load, but still helps with the lean spots on load.  I figure I don't have much reason to be above 2500rpm with no load.  When watching other videos it seems their target is reached much faster than mine.  Mine takes forever to adjust and reach the target. My next few days will be spent making sure timing is good, it was running fine before doing the ECU and DBW swap, but want to verify.  I'll also probably swap in the new injectors I bought as well as a walbro 255 pump.  
    • It would be different if the sealant hadn't started to peel up with gaps in the glue about ~6cm and bigger in some areas. I would much prefer not having to do the work take them off the car . However, the filler the owner put in the roof rack mount cavities has shrunk and begun to crack on the rail delete panels. I cant trust that to hold off moisture ingress especially where I live. Not only that but I have faded paint on as well as on either side of these panels, so they would need to come off to give the roofline a proper respray. My goal is to get in there and put a healthy amount of epoxy instead of panel filler/bog and potentially skin with carbon fiber. I have 2 spare rolls from an old motorcycle fairing project from a few years back and I think it'd be a nice touch on a black stag.  I've seen some threads where people replace their roof rack delete with a welded in sheet metal part. But has anyone re-worked the roof rails themselves? It seems like there is a lot of volume there to add in some threads and maybe a keyway for a quick(er) release roof rack system. Not afraid to mill something out if I have to. It would be cool to have a cross bar only setup. That way I can keep the sleek roofline that would accept a couple bolts to gain back that extra utility  3D print some snazzy covers to hide the threaded section to be thorough and keep things covered when not using the rack. 
×
×
  • Create New...