Jump to content
SAU Community

Recommended Posts

Hehe, I've been working on my Albert to English translations for a while. I can even do English to Albert :D

Bert, prob same as last, cbf go all the way there to come all the way back. neg plans might sit on side of road waitin, otherwise it's thorns again... n shit...

  • Replies 239
  • Created
  • Last Reply

Top Posters In This Topic

Top Posters In This Topic

Posted Images

i don't think the ferries are lowered car friendly

Hey guys, I live there, the ferry is pretty easy to get onto. Plenty of clearance but I'll check it out for you guys.

Albert I'd say it's about a 40 minute cruise, or a 60 minute amble :P Some beautiful corners through Arcadia.

Hehe, I've been working on my Albert to English translations for a while. I can even do English to Albert :P

Bert, prob same as last, cbf go all the way there to come all the way back. neg plans might sit on side of road waitin, otherwise it's thorns again... n shit...

Doof, you can come in mine, provided I have it ready by then :D

Hehe, I've been working on my Albert to English translations for a while. I can even do English to Albert :)

Bert, prob same as last, cbf go all the way there to come all the way back. neg plans might sit on side of road waitin, otherwise it's thorns again... n shit...

yeha yeha what eves

cbf english pretty much aye

sooo 50 decades ago..

Hey guys, I live there, the ferry is pretty easy to get onto. Plenty of clearance but I'll check it out for you guys.

Albert I'd say it's about a 40 minute cruise, or a 60 amble thrash :( Some beautiful corners through Arcadia.

Oh good, Can you post up a route map for me please Steve :)

I notice this is being on a sunday, doh - you are teh suck Albert!

edit - Zilch - please edit your post :)

Oh Chris its like a month notice.. N/A it much

+ I like drunken dirty sunday arvos :D

yeha yeha what eves

cbf english pretty much aye

sooo 50 decades ago..

Oh good, Can you post up a route map for me please Steve :thumbsup:

Oh Chris its like a month notice.. N/A it much

+ I like drunken dirty sunday arvos :thumbsup:

Yeah no worries, I'll sort that out for you mate. Between work hours :)

They are currently widening the 1st part of the Berowra Waters Road down to the ferry so I'll have to wait till they're gone before I can check clearance for you guys but I'm fairly sure if you go sideways you won't scrape, I never have(although the new car might) and my line was fairly low.

Yeah no worries, I'll sort that out for you mate. Between work hours :thumbsup:

They are currently widening the 1st part of the Berowra Waters Road down to the ferry so I'll have to wait till they're gone before I can check clearance for you guys but I'm fairly sure if you go sideways you won't scrape, I never have(although the new car might) and my line was fairly low.

I don't know if they have changed it recently but I've only been there once about 18 months ago. My car had no chance of getting on to the ferry.




  • Similar Content

  • Latest Posts

    • Possibly avoid using a Cometic one unless the deck/head surface are perfectly flat. I did have a look just then and forgiving gaskets such as Tomei or Nitto don't exist for the FJ20, however the Bar-Tek or Kameari ones look good and might do the trick.
    • Because pipe threads for pipe things. M threads for bolt things. Throw some teflon sealant onto it and dust your hands off knowing you did the right thing, instead of going twice around the block to achieve a result using the wrong things. Of course, all of these solutions are ignoring the fact that the minimum thread pitch we're talking about here is 1.25mm, with the 1/4" in NPT or BPS being out around 1.4mm. You will need to know that the boss you're tapping has enough thickness for at least a few threads. That's one of the reasons that 1/8" is commonly used - because the pitch is <1mm. And why would you look to use 1/4" NPT in a BSP country anyway? Ugh.
    • Just throwing around ideas, does it need to be in the compressor cover? Why not the hot side piping?
    • 1/8NPT drill size = 8.7mm. Since the hole got messed up by me, it’s probably around 9mm.    So 1/4” NPT would be next step. A drill size of around 11mm would be preferred there which is not way of my M12 (drill 10.5mm and tap M12 threads) 
    • 3 Kids are starting to hit that ages. I wanted to get them something special to learn on, put down the screens and have some fun. 4Door 2001 R34DE Black Pearl GV1 Jap Import, AU 2nd owner. Pre Work done. Suspension - Wheels Pedders SportsRyder Coilovers   Wheels TSG Spokey Boi 18'x9.5"+15 Body JASI Aero 4 door Type R Full Kit LED Conversion - Parker, Blinkers, & Reverse Exhaust Hurricane Headers 100 CPI high flow cat 2.5" Piping Cannon muffler Internal Bride low max stradia ii - front seats  Bride RO seat base and Rails (R/H) Cube short shifter LED Conversion - Interior   
×
×
  • Create New...