Jump to content
SAU Community

Recommended Posts

I looked but didn't really find anything useful so I will ask. I want to get oil pressure/water temp/boost gauges but when I fit them I would like them to sit beneath my head unit where the din pocket goes. Is this possible? If so, how can it be done? I reckon they would look mint there. Any other suggestions?

Cheers,

Evan

Link to comment
https://www.sau.com.au/forums/topic/229573-gauges-in-din-pocket-area/
Share on other sites

been done plenty of times dude, might be a tight squeeze for 3 guages unless you allow it to take up both pockets although i think i have seen it done in the one pocket, you could try using some aluminum sheet and just cut the holes for the guages where you want them to sit, the fix the plate in place where the din pocket screws go

Hey,

Yeah it can be done pretty easy. You could get the Defi din Gauges or you can get the justjap gauges. Justjap do a package where you get 3 gauges (boost, oil temp, water temp) and a metal plate that will fit under your deck. There are also 3 different type of packages with different gauges. Cost $175 all up for the Justjap package or around $500 for the defi din gauges :thumbsup:

Just make sure you dont buy the din GTR gauges... i did that and then found out that i couldnt use them in my gts-t...lol

http://justjap.com/store/home.php?cat=267

post-43948-1216943097_thumb.jpg

post-43948-1216943162_thumb.jpg

Edited by R33Matt

Terrific, thanks everyone for your replies. I like the defi gauges a LOT but damn theyre expensive for 3 gauges... Any experience with the jjr gauges? Are they accurate? And it doesn't quite specify if they are electric gauges or mechanical. I don't really like the idea of hot oil and water lines going thru into the cabin of my car...

Cheers,

Evan

Yeah the JustJap gauges that come in the package are mechanical, but you could buy the metal plate for $20 and then buy the electric gauges seperate. They sell the electric gauges as well for $90 each. Ive used a Autogauge Boost Gauge in my R32 before and had no problems :thumbsup:

post-43948-1216957720_thumb.jpg

  • 3 weeks later...

hey mate

check this: scroll down for the interior pic

http://nissansilvia.com/forums/index.php?showtopic=269140

u will see i just got a 3 din c/f surround and passed all my gauges through there...

dont ask me where i got it from, a mate gave it to me so i guess try autobarn or just jap???

Does anyone know if that Defi DIN gauge set can actually replace the original gauges in the GTR?

Also does it come with a boost gauge? it doesn't say

The defi din consists of 1x Pressure and 2x Temperature.

So you connect the pressure to either boost or oil etc

  • 2 weeks later...
  • 2 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I wasn’t able to replicate the sound anymore. It was a one time sound so maybe it was just coincidence but it was like small pebbles being dropped in a coke can.   should I try cleaning the MAF? It could be it’s functioning but dirty? I don’t know.
    • Update 4: Hi all. The car drives again! Haven't driven for long, only to store it in the garage again, but the test drive was successful. The coolant and oil leaks seem to be fixed for now. Temps on the engine were also very good, while moving I never even saw 80C water during the approx. 30 minute drive. Ate up all the coolant in the reservoir though so will have to fill that even more when I go to the car next time. One thing that pisses me off is that the RPM gauge is still f**ked, I even resoldered the board twice and used copper paste on the silly screws that are used as connections. Next time I take it out I'll take apart the board and fit new components, I'll see if I can get a replacement IC for it.  I have an appointment set for 22nd of September for the engine tune to 370hp. Alignment also still needs to be done. My hope is that I can get all the legal stuff over with by the end of this season. Anyone of you have advice regarding intercoolers? Currently there is an APEXI core fitted, one of those weird hybrid ones, 600x270x76. I don't think it's bad but it's not new and now I still have the chance to change it now to legally include it in the paperwork. Only issue is that the only options that would arrive in time are a HKS Type R intercooler or generic Ebay spec intercoolers comparable to a JustJap one. Ideally I'd order a Plazmaman but it takes over a month to receive which would mean making the car legal has to wait until next season. Would love to hear some input on this. Same story for my injectors, the previous owner was a nunce and put ID 1050x on the engine. They work but are obviously not ideal at "normal" power levels. But I don't see a reason to change them unless the tuner says it's necessary. I read online before buying a different exhaust that the top secret style rear diffusers won't fit due to the size of the rear resonators. My buddy and I made it work by slightly "adjusting the shape" of the mounting bracket and making some spacers out of 3d print for the mounting bolts. Fits like a charm. Just putting this here in case someone has this problem. Even the hefty HKS Silent Hi Power rear can fits without hitting anything.
    • Well they got my money but they are not getting my gearbox ! 
    • It's needed for rolling idle up, and I think it is a decider on VCT also.
    • I mean, not really. Link ECU's can absolutely still have errors from the ECU thinking it's getting a sensor it's not expecting. I would imagine the speed at the ECU level in Nistune does absolutely nothing anyway? I assume the ECU does not do any fancy TC stuff with regards to front+rear wheel speed or anything of that like anyway. Someone who uses Nistune may be more fluent in it. 
×
×
  • Create New...