Jump to content
SAU Community

Recommended Posts

hi to all i got a slight problem dont know what it is as i am new to skylines i just installed a pod filter in my r33 and when ever i hit boost in normal driving i can hear a beeping noise coming from towards the left hand side of the car i can not figure out if its coming from the engine or somewhere in the car if any one knows the problem please tell me because its really annoying and do not want to damage the car in anyway because of that beeping noise thanks!!!

Link to comment
https://www.sau.com.au/forums/topic/230174-pod-filter-in-series-1-r33/
Share on other sites

I took my JDM stereo out a few months ago and since then ive been hearing it. As i havnt put a new stereo in yet and have left the large hole in the dash i can hear it more louder although its still very faint. I cant spot where its coming from but seems to be near the heater unit in the behind the dash somewhere. Its defiently electronic. It beeps once every 1.5 secs or so. Ive noticed it more on cold mornings when its dark but not when im coming home from work when its warmer and daylight.

should not be anything to do with the pod filter modification, even if the afm is played with i dont think it triggers a beeping sound..i'd say it is electrical...try identify wat region it is coming from, maybe take it to someone e.g a mechanic and take him/her for a drive..

mine does a similar problem, when im cruising in 5th gear and hold my accelerator in the same spot for a minute, this 'faint beeeeeeeeeppp' sound will start, soon as i just release the peddle or press it a wee bit more it stops, then if i hold it in that same spot it'l start again...:S

definetly sounds like its comin from the drivers side

?

i sometimes get a high pitched sound coming from my engine bay. But once i rev it to get if over idle rpm it goes away, then when it drops back to idle rpm it continues to make it. Just confused because i don't know wtf it could be.

i sometimes get a high pitched sound coming from my engine bay. But once i rev it to get if over idle rpm it goes away, then when it drops back to idle rpm it continues to make it. Just confused because i don't know wtf it could be.

Not the timing belt or something?

Not the timing belt or something?

Hmmm nuh i dont think a timing belt can make that kind of sound lol. What i think it might be is (just thought of it) is my HKS SSQV is sucking in air on idle. Have to check it out.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hi all,   anyone know where I can pick one of these up for a reasonable price? I just resprayed my rear trunk due to fuel stain and my new muse spat install.    added a photo for some content 🤣👍   thanks 
    • Consider a 35 too...
    • He's right ~ there is no 'magic' with stuff like this ... it is more likely that in the process of looking for the short, the loom/wire 'incidentally' got moved in the process, thus removing the short ~ now, that maybe a wire (in a loom) rubbing against the edge of some grounded metal, that's worn through the insulation, causing the (now intermittent) short to ground. If one wire in a loom has been damaged in this fashion, it's reasonable to presume that other wires beside it may have also be damaged, and now exposed...you can bet the green crusty copper corrosion will start... ...that'd be a pisser, Murphy's Law steps right in as GTS observes...but worse, something like that is easier to find when shorted...ie; unplug bulb and fuse, and put multimeter in continuity mode so you get constant beep, and carefully poke about hoping to find if some movemet of the harness stop the beeping.... ...it's still all a bit Arnie tho' ..It'll be back... 😃
    • Yeah, but knowledge of one wire's insulation worn through to short on earth implies the possibility of other wires doing the same. I had my power steering die, because the wire that runs to the solenoid valve on the rack runs in the same loom as the power wire for the O2 sensor. And when the O2 sensor/wire did something stupid and burnt part of that loom to death, the only indication was the shit(ter) fuel economy and the heavy steering. It took deep excavation of the looms in the bay to find the problem. Not wear through in that case, but similar shit.
    • Ah, I thought he'd wired it to one of the spare ECU inputs! Too long ago since I read that post, ha ha. I've been arguing with radiators, harmonic balancers, alternators and rust since reading it.
×
×
  • Create New...