Jump to content
SAU Community

Recommended Posts

Hi guys this is my first post so go easy.

Anyway i have recently bough an R33 with a GT3040 (vg30 rear .68 housing, in stock comp cover) and find it way too laggy....starts to just come on at around 4200rpm and gets going around 5000rpm. Its pretty stock only having a 3" Blitz exhaust (straight through) and Tomei 255l pump.

At first i thought the extra lagg was good because when my g/f drives it its very tame but now i really am looking for more power especially down low!!!!! I know i need to get a power fc, injecters and front mount b4 i wind up the boost but i dont see the point if its just going to make more power up top and still have nothing down low. Top end is not bad now but revving to 7k every time i want to over take isnt the best.

I'm very tempted to put a stock turbo on it and just drive it.

Any thoughts would be great.

Cheers james!

Link to comment
https://www.sau.com.au/forums/topic/230687-r33-with-gt3040/
Share on other sites

  • Replies 40
  • Created
  • Last Reply

Top Posters In This Topic

Hi guys this is my first post so go easy.

Anyway i have recently bough an R33 with a GT3040 (vg30 rear .68 housing, in stock comp cover) and find it way too laggy....starts to just come on at around 4200rpm and gets going around 5000rpm. Its pretty stock only having a 3" Blitz exhaust (straight through) and Tomei 255l pump.

At first i thought the extra lagg was good because when my g/f drives it its very tame but now i really am looking for more power especially down low!!!!! I know i need to get a power fc, injecters and front mount b4 i wind up the boost but i dont see the point if its just going to make more power up top and still have nothing down low. Top end is not bad now but revving to 7k every time i want to over take isnt the best.

I'm very tempted to put a stock turbo on it and just drive it.

Any thoughts would be great.

Cheers james!

I have a 3040 on my r33 has .82 rear starts spooling at 3500 full boost (18psi)at 4000.

are you using the stock exhaust manifold

what size dump pipe

Link to comment
https://www.sau.com.au/forums/topic/230687-r33-with-gt3040/#findComment-4053070
Share on other sites

Yes its a stock manifold and yes its a genuine garret built by ATS in Melbourne. I would have thought with the 0.62 it would spool up a lot quicker especially under load in 3rd. I would love it to start at 3000rpm!

Will a tune (with power fc) help this or do my problems lie somewhere else?

Also it seems to be running very low boost (looks around 4psi), but i will confirm with an aftermarket guage in the next few days. Am i able to use an adjustable boost controller and wind it up to say 8 or 9 psi with stock computer???

Once again thanks in advance.

James

Link to comment
https://www.sau.com.au/forums/topic/230687-r33-with-gt3040/#findComment-4053416
Share on other sites

change the actuator on the turbo to an ajustable one. Thats what i had on it a while ago before i restored it to standard.

When i had it setup i was making fullboost by 3,800.

Get an ajustable actuator (hks)

ecu (will bring boost on earlier)

front mount cooler

Then youl be good as gold

Link to comment
https://www.sau.com.au/forums/topic/230687-r33-with-gt3040/#findComment-4053510
Share on other sites

Check you boost actuator; if it's soft or lazy it will be opening the internal gate too early, causing turbo to be laggy and not boost up properly.

I would personally take it to a mechanic that has a dyno and knows how to diagnose these issues.

Link to comment
https://www.sau.com.au/forums/topic/230687-r33-with-gt3040/#findComment-4053511
Share on other sites

i would change the exhaust manifold, get a power fc and adjustable exhaust cam gear

Hell no. Not worth the $'s with that turbo/setup. I made 275rwkw with the standard manifold and great response using a turbo very similar to this and a GTRS.

I have seen others make over 330rwkw using the std manifold.

As others have stated:

- ECU + tune

- Good actuator

- turbo back exhaust

- fmic

then to optimize the set-up

- Injectors

- Boost controller

Link to comment
https://www.sau.com.au/forums/topic/230687-r33-with-gt3040/#findComment-4053648
Share on other sites

its not about making power. you want to make it came onboost faster. when my car was running a apexi rx6b turbo i change the stock manifold for a stainless low mount it started coming onboost 1000 rpm faster. didnt give it a bigger number on the dyno but made it faster.

Link to comment
https://www.sau.com.au/forums/topic/230687-r33-with-gt3040/#findComment-4053928
Share on other sites

1000rpm is unlikely but this isnt an apexi RX6 were talking about, its a cropped vg30 rear

nothing like an RX6 housing

it would be silly using an rx6 on stock manifold, it would be like trying a t67 or t88

Link to comment
https://www.sau.com.au/forums/topic/230687-r33-with-gt3040/#findComment-4053953
Share on other sites

1000rpm just from a manifold on what isnt a big turbo in most terms...

Interesting...

Agreed :D

Also....fitting a hiflowed std turbo to a high mount manifold is a BIG waste of money. This turbo should be making full boost by 3800-4000rpm max.; if it's not, there is something wrong with the setup/tune. Fitting a top mount manifold will not fix the problem.

Link to comment
https://www.sau.com.au/forums/topic/230687-r33-with-gt3040/#findComment-4058077
Share on other sites

Ok bit of an update.

I fit a boost gauge today and its boosting to only around 4psi. I fit a manual boost controller and nothing happend....... I went back and had a look and the wastegate flap thingy was set so that it was open all of the time!!!! Obviously the previous owner had done this after he pulled the supporting mods off to keep it safe!

Well i angled the actuator so that it was shut and went for a quick spin and geeeeee what a difference. Boost starts at 3000rpm and keeps going until around 8psi. I could actually year the turbo this time. Anyway i only did this once or twice and cruised home so not to do any damage and will put it back the way i was.

I'm just happy to find out that it was something very simple and cant wait to get it tuned once a get an ECU.

Thanks

James

PS: Does the standard ecu warn if the injecters are at 100% duty and i'm leaning out?

Does anyone think its safe to run maybe 5-6psi? I want to put it back so the wastegate is shut and i can get some reasonable low down torque but not want it to boost any higher then say 6psi.

Link to comment
https://www.sau.com.au/forums/topic/230687-r33-with-gt3040/#findComment-4058122
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • From there, it is really just test and assemble. Plug the adapter cables from the unit into the back of the screen, then the other side to the car harness. Don't forget all the other plugs too! Run the cables behind the unit and screw it back into place (4 screws) and you should now have 3 cables to run from the top screen to the android unit. I ran them along the DS of the other AV units in the gap between their backets and the console, and used some corrugated tubing on the sharp edges of the bracket so the wires were safe. Plug the centre console and lower screen in temporarily and turn the car to ACC, the AV should fire up as normal. Hold the back button for 3 sec and Android should appear on the top screen. You need to set the input to Aux for audio (more on that later). I put the unit under the AC duct in the centre console, with the wifi antenna on top of the AC duct near the shifter, the bluetooth antenna on the AC duct under the centre console The GPS unit on top of the DS to AC duct; they all seem to work OK there are are out of the way. Neat cable routing is a pain. For the drive recorder I mounted it near the rear view mirror and run the cable in the headlining, across the a pillar and then down the inside of the a pillar seal to the DS lower dash. From there it goes across and to one USB input for the unit. The second USB input is attached to the ECUtec OBD dongle and the 3rd goes to the USB bulkhead connected I added in the centre console. This is how the centre console looks "tidied" up Note I didn't install the provided speaker, didn't use the 2.5mm IPod in line or the piggyback loom for the Ipod or change any DIP switches; they seem to only be required if you need to use the Ipod input rather than the AUX input. That's it, install done, I'll follow up with a separate post on how the unit works, but in summary it retains all factory functions and inputs (so I still use my phone to the car for calls), reverse still works like factory etc.
    • Place the new daughterboard in the case and mount it using the 3 small black rivets provided, and reconnect the 3 factory ribbon cables to the new board Then, use the 3 piggyback cables from the daughterboard into the factory board on top (there are stand offs in the case to keep them apart. and remember to reconnect the antenna and rear cover fan wires. 1 screw to hold the motherboard in place. Before closing the case, make a hole in the sticker covering a hole in the case and run the cable for the android unit into the plug there. The video forgot this step, so did I, so will you probably. Then redo the 4 screws on back, 2 each top and bottom, 3 each side and put the 2 brackets back on.....all ready to go and not that tricky really.      
    • Onto the android unit. You need to remove the top screen because there is a daughterboard to put inside the case. Each side vent pops out from clips; start at the bottom and carefully remove upwards (use a trim remover tool to avoid breaking anything). Then the lower screen and controls come out, 4 screws, a couple of clips (including 3 flimsy ones at the top) and 3 plugs on the rear. Then the upper screen, 4 screws and a bunch of plugs and she is out. From there, remove the mounting brackets (2 screws each), 4 screws on the rear, 2 screws top and bottom and 3 screws holding in the small plates on each side. When you remove the back cover (tight fit), watch out for the power cable for the fan, I removed it so I could put the back aside. The mainboard is held in by 1 screw in the middle, 1 aerial at the top and 3 ribbon cables. If you've ever done any laptop stuff the ribbon cables are OK to work with, just pop up the retainer and they slide out. If you are not familiar just grab a 12 year old from an iphone factory, they will know how it works The case should now look like this:
    • Switching the console was tricky. First there were 6 screws to remove, and also the little adapter loom and its screws had to come out. Also don't forget to remove the 2 screws holding the central locking receiver. Then there are 4 clips on either side....these were very tight in this case and needed careful persuading with a long flat screw driver....some force required but not enough to break them...this was probably the fiddliest part of the whole job. In my case I needed both the wiring loom and the central locking receiver module to swap across to the new one. That was it for the console, so "assembly is the reverse of disassembly"
    • But first....while I was there, I also swapped across the centre console box for the other style where the AV inputs don't intrude into the (very limited !) space.  Part# was 96926-4GA0A, 284H3-4GA0B, 284H3-4GA0A. (I've already swapped the top 12v socket for a USB bulkhead in this pic, it fit the hole without modification:) Comparison of the 2: Basically to do the console you need to remove the DS and PS side console trim (they slide up and back, held in by clips only) Then remove the back half of the console top trim with the cupholders, pops up, all clips again but be careful at the front as it is pretty flimsy. Then slide the shifter boot down, remove the spring clip, loose it forever somewhere in the car the pull the shift knob off. Remove the tiny plastic piece on DS near "P" and use something thin and long (most screwdrivers won't fit) to push down the interlock and put the shifter down in D for space. There is one screw at the front, then the shifter surround and ashtray lift up. There are 3 or 4 plugs underneath and it is off. Next is the rear cover of the centre console; you need to open the console lid, pop off the trim covering the lid hinge and undo the 2rd screw from the driver's side (the rest all need to come out later so you can do them all now and remove the lid) Then the rear cover unclips (6 clips), start at the top with a trim tool pulling backwards. Once it is off there are 2 screws facing rearwards to remove (need a short phillips for these) and you are done with the rear of the console. There are 4 plugs at the A/V box to unclip Then there are 2 screws at the front of the console, and 2 clips (pull up and back) and the console will come out.
×
×
  • Create New...