Jump to content
SAU Community

Recommended Posts

Check you boost actuator; if it's soft or lazy it will be opening the internal gate too early, causing turbo to be laggy and not boost up properly.

I would personally take it to a mechanic that has a dyno and knows how to diagnose these issues.

*cough* :ermm:

To set the actuator properly the hole on the actuator shaft should be about half a hole short from fitting on the gate pin. You then need to pull the arm so that the pin fits through the hole. This will provide the right preload/tension on the gate.

The std ecu normally runs pretty rich, so if you have a std 7psi actuator i would dare say it would be ok. If you do not have the money for an ecu and tune i would seriously find a w/shop doing a "dyno day", adjust the actuator just before going on the dyno and inform the tuner/mechanic of the situation and to keep an eye/ear out for a/f ratios and detonation. This way it will only cost you about $40-$50, instead of the $120+ w/shops may charge to do a single run.

All the best.

  • 4 weeks later...
  • Replies 40
  • Created
  • Last Reply

Top Posters In This Topic

The rear housing is more of the restriction, not the front

VG30 machine jobbies always choke up

Made over 270rwkw@16psi with mine, proven both on EAS and Racingline dyno's. My old one is now hanging off the side of a std NEO engine making over 270rwkw@16psi too. Any more boost was useless as that's about the limitations of this turbo.

Hardly a "choke up" though :rolleyes:

Made over 270rwkw@16psi with mine, proven both on EAS and Racingline dyno's. My old one is now hanging off the side of a std NEO engine making over 270rwkw@16psi too. Any more boost was useless as that's about the limitations of this turbo.

Hardly a "choke up" though :(

If its @ a limit on 16psi, its choking.

the compressor of that combo is good for over 300

  • 3 months later...

Hello all, I thought i would dig up an old thread.

Have since apgraded injectors AFM and have a blitz front mount and its currently making around 250rwkw on 15psi.

Anyway from other ppls results i have seen that with the 0.62 rear housing this turbo doesnt make much more after around 16psi which i'm nearly at. My question is it worth fitting an adjustable ex cam gear to this setup and getting a retune? I'm running the standard air box with a k&n filter and standard everything else.

Thanks again

James

PS: i did a search but most of the results were in regards to stock turbos. Thought mine might be a little different

Edited by Bond

you should be able to make more power with an adjustable exh cam gear (assuming you are not talking a NEO RB25DET). at the very least you should be able to move the power curve around to where it helps you the most. you can make 5-10kw from midrange to top end.

Also i'm lead to beleive that my 0.62 rear housing is holding me back in regards to top end power (is there any way of testing which side is hiolding me backCan anything be done to get some more out of it or do i have to bite the bullet and upgrade to a 0.82 (or whatever it is).

Thanks

James

check out what the mafia squeezed out of the 0.63 housing on his GT3076.

i am pretty sure you can make at least 270rwkw or thereabouts with the 0.63 housing.

the compressor will clearly flow more but it should make 250rwkw comfortably.

sure you dont want to add Tomei poncams and some head work :P

lol nah, cant comment on that ^ as I havent got my baby back yet, soon my pretties, soon ....

for a larger rear housing, turbo off/on etc, labour from shop, id say $600 to supply/replace rear housing?

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • It is a kunfine Android screen . Does anyone know the wirering diagram of the fuga ??
    • just an update to this, poor man pays twice  Tried sanding down the pulleys but it didnt do the trick. Chucked another second hand alternator in the na car which I got for free off my mate and its fixed the squelling. Must have been unlucky with the bearings.    As for my turbo car, I managed to pick up a cwc rb alternator conversion bracket + LS alternator for 250 off marketplace, looked to be in really good nick. Installed it , started the car and its not charging the battery.... ( Im not good with auto elec stuff so im not sure if this was all I needed to do but I verified such by using a multimeter on the battery when the engine was running and I was only getting 12.2v )   I had to modify the earth strap for the new LS alternator , factory earth strap was a 10mm bolt which did not fit the bolt on the LS alternator which was double the size so I cut it off , went to repco bought some ring terminals that fit, crimped it onto the old earth strap and bolted it up to the alternator , started the car and same issue. Ran like shit and was reading 12.2 at the battery.  For a "plug and play" advertised kit thats not very plug and play but alas.  My question is , am I missing something ? Ive been reading that some people recommend upgrading the stock 80 amp alternator fuse to a 140 amp but I dont see how that would stop the alternator charging especially at idle not under load.  Regardless ive pulled it out and am going to get it bench tested by an auto elec tomorrow but it would be handy to know if ive missed something silly or have done something wrong.   
    • My wild guess is that you have popped off an intake pipe....check all of the hoses between the turbo and the throttle for splits or loose clamps.
    • Awesome, thanks for sharing!
    • To provide more specific help, more information is needed. What Android screen? What is its wiring diagram? Does the car's wiring have power at any required BAT and ACC wires, and is the loom's earth good?
×
×
  • Create New...