Jump to content
SAU Community

Recommended Posts

g'day.

Im looking at getting Bridgestone Adrenaline RE001s to fit on my R34 GTR rims (fitted on my R32 GTR).

What size do you guys recommend for these rims? Is it better to go more narrow for the fronts or keep them all the same widths?.

R34 gtr rims are 18" x 9".

The car will be predominately street use with the occassional track day.

Link to comment
https://www.sau.com.au/forums/topic/231856-optimum-tyre-specs-for-r34-gtr-rims/
Share on other sites

g'day.

Im looking at getting Bridgestone Adrenaline RE001s to fit on my R34 GTR rims (fitted on my R32 GTR).

What size do you guys recommend for these rims? Is it better to go more narrow for the fronts or keep them all the same widths?.

R34 gtr rims are 18" x 9".

The car will be predominately street use with the occassional track day.

Hey mate, I had the same rims on the same car, i put on bridgstone potenza SO-3's. they were 255/35/18's. they were a very very good tyre and didnt scrub at all.. hope this helps..

Thanks guys for your replies. I think i will take heed on the 255/35/18 on all corners. I am now looking at importing some Bridgestone RE-01R's from Tirerack.com. I heard they are pretty damn sticky and are a good compromise for street and a little bit of track work. Used to have Yoko Advans but didn't rate them much. If i cant get my hands on the RE-01rs, i may consider Federal 595 RS-R or Toyo T1-Rs. Its all too confusing, too many options and opinions out there. :wave:

Those rims came standard with 245's... which fit well... 255's will fit ok too, touch more baggy.

i have 255 michelins on my 34s and they're actually slightly stretched.

given that manufacturers widths vary between brands, a 245 or 255 road would be fine.

I've seen some 265 road tyre fitments on 34 wheels where the sidewalls are straight up - not baggy

hey godspeed,

i had 285 SO3 bridgestones on my r33GTR, they fit sweet, looked like a beast ha, but tram lined quite badly, went down to 255 toyo's, fixed problem

Edited by donkey

245s are the way to go on 9inch wide rims in my opinion. depends on the tyre of course too. I've tried 235, 245 and 255 on 9 inch wide rims. all are ok (though the 235s have always been semi slicks which are about the same width as a 255 road tyre).

so to recap, go for the 245s all round. either 40 or 45 profile.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I wasn’t able to replicate the sound anymore. It was a one time sound so maybe it was just coincidence but it was like small pebbles being dropped in a coke can.   should I try cleaning the MAF? It could be it’s functioning but dirty? I don’t know.
    • Update 4: Hi all. The car drives again! Haven't driven for long, only to store it in the garage again, but the test drive was successful. The coolant and oil leaks seem to be fixed for now. Temps on the engine were also very good, while moving I never even saw 80C water during the approx. 30 minute drive. Ate up all the coolant in the reservoir though so will have to fill that even more when I go to the car next time. One thing that pisses me off is that the RPM gauge is still f**ked, I even resoldered the board twice and used copper paste on the silly screws that are used as connections. Next time I take it out I'll take apart the board and fit new components, I'll see if I can get a replacement IC for it.  I have an appointment set for 22nd of September for the engine tune to 370hp. Alignment also still needs to be done. My hope is that I can get all the legal stuff over with by the end of this season. Anyone of you have advice regarding intercoolers? Currently there is an APEXI core fitted, one of those weird hybrid ones, 600x270x76. I don't think it's bad but it's not new and now I still have the chance to change it now to legally include it in the paperwork. Only issue is that the only options that would arrive in time are a HKS Type R intercooler or generic Ebay spec intercoolers comparable to a JustJap one. Ideally I'd order a Plazmaman but it takes over a month to receive which would mean making the car legal has to wait until next season. Would love to hear some input on this. Same story for my injectors, the previous owner was a nunce and put ID 1050x on the engine. They work but are obviously not ideal at "normal" power levels. But I don't see a reason to change them unless the tuner says it's necessary. I read online before buying a different exhaust that the top secret style rear diffusers won't fit due to the size of the rear resonators. My buddy and I made it work by slightly "adjusting the shape" of the mounting bracket and making some spacers out of 3d print for the mounting bolts. Fits like a charm. Just putting this here in case someone has this problem. Even the hefty HKS Silent Hi Power rear can fits without hitting anything.
    • Well they got my money but they are not getting my gearbox ! 
    • It's needed for rolling idle up, and I think it is a decider on VCT also.
    • I mean, not really. Link ECU's can absolutely still have errors from the ECU thinking it's getting a sensor it's not expecting. I would imagine the speed at the ECU level in Nistune does absolutely nothing anyway? I assume the ECU does not do any fancy TC stuff with regards to front+rear wheel speed or anything of that like anyway. Someone who uses Nistune may be more fluent in it. 
×
×
  • Create New...