Jump to content
SAU Community

Recommended Posts

Nissan do this, it means you have the special million dollar winning car,

Nah, but unscrew the 4 screws in the speedo, pull it out, check the speedo cable is plugged in properly, if it is, then check the sensor at the other end(gearbox end is still working, follow the cable up, sometimes they snap, if it's buggered just get a new speedo cable, if it's not, then you might need to take it to a mechanic, something must be stopping it from spinning)

If the speedo and P/S are still working, then it shouldn't be a problem with the cable.

The Japanese seem less opposed to fiddling odometers (winding them back). It's possible some sort of damage was done that prevents the odometer going past 100k.

I have the same problem as mine started to play up at 75000kms and fixed itself.

It has now hit 80000kms and wont budge, even the trip meter has stopped.

So I pulled it apart today and had a look seemed easy enough but I couldn't find anything wrong so I just pushed the odometer numbers gently past 80000 with a small screwdriver.

Dunno if this has worked yet as my radiator is out and I cant drive it.

Will let you know as soon as I do tho.

On a side note my boost guage seems to be playing up.

When Im idling the guage reads 0 pressure not vacuum, but when I start to boost it it climbs up.

Also noticed that when the car is off it falls down to 7 deg vacuum.

Any ideas????

I have exactly the same problem.......

the ODO meter stop when reaching 89999kms

yes, four 9 and doesn't go past the 90000kms!

and the trip meter also stopped........

I opened it up and can see nothing wrong

went to wrecker to buy a used one.

realise that the one I had......doesn't have the P, R, N, D, 1, 2......at the centre......

so I am guessing it is for a manual car

and now maybe I could understand why the O/D light doesn't turn on

so what's the reason behind the not running odometer?

i heard that when your car is moving, you shouldn't reset the trip meter..........but I need confirmation about that lol

and also I think it stopped before I reset -_-"

This is what we were concerned about at 5 mins to midnight on 31/12/99 eh?

Had an N13 that did the same thing, and after about 2 months, the odo moved on. Might have been after speed hump rather than a chicane.... Silly isn't it!

Rubber Mallet? I'll LOL if that works!

the car's odometer just stopped in shock when it realised it was the second time it had clicked over 100,000klm :( I guess they wound it back a fair way.

no idea how to fix it but it is pretty common with these cars

pull it apart and look for the cogs from memory there is one white one and severl black ones, check to see if they are all lined up and "meshing" nicely in there, also make sure no damage to the shaft and that everything is plugged in! Gl hame.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • From there, it is really just test and assemble. Plug the adapter cables from the unit into the back of the screen, then the other side to the car harness. Don't forget all the other plugs too! Run the cables behind the unit and screw it back into place (4 screws) and you should now have 3 cables to run from the top screen to the android unit. I ran them along the DS of the other AV units in the gap between their backets and the console, and used some corrugated tubing on the sharp edges of the bracket so the wires were safe. Plug the centre console and lower screen in temporarily and turn the car to ACC, the AV should fire up as normal. Hold the back button for 3 sec and Android should appear on the top screen. You need to set the input to Aux for audio (more on that later). I put the unit under the AC duct in the centre console, with the wifi antenna on top of the AC duct near the shifter, the bluetooth antenna on the AC duct under the centre console The GPS unit on top of the DS to AC duct; they all seem to work OK there are are out of the way. Neat cable routing is a pain. For the drive recorder I mounted it near the rear view mirror and run the cable in the headlining, across the a pillar and then down the inside of the a pillar seal to the DS lower dash. From there it goes across and to one USB input for the unit. The second USB input is attached to the ECUtec OBD dongle and the 3rd goes to the USB bulkhead connected I added in the centre console. This is how the centre console looks "tidied" up Note I didn't install the provided speaker, didn't use the 2.5mm IPod in line or the piggyback loom for the Ipod or change any DIP switches; they seem to only be required if you need to use the Ipod input rather than the AUX input. That's it, install done, I'll follow up with a separate post on how the unit works, but in summary it retains all factory functions and inputs (so I still use my phone to the car for calls), reverse still works like factory etc.
    • Place the new daughterboard in the case and mount it using the 3 small black rivets provided, and reconnect the 3 factory ribbon cables to the new board Then, use the 3 piggyback cables from the daughterboard into the factory board on top (there are stand offs in the case to keep them apart. and remember to reconnect the antenna and rear cover fan wires. 1 screw to hold the motherboard in place. Before closing the case, make a hole in the sticker covering a hole in the case and run the cable for the android unit into the plug there. The video forgot this step, so did I, so will you probably. Then redo the 4 screws on back, 2 each top and bottom, 3 each side and put the 2 brackets back on.....all ready to go and not that tricky really.      
    • Onto the android unit. You need to remove the top screen because there is a daughterboard to put inside the case. Each side vent pops out from clips; start at the bottom and carefully remove upwards (use a trim remover tool to avoid breaking anything). Then the lower screen and controls come out, 4 screws, a couple of clips (including 3 flimsy ones at the top) and 3 plugs on the rear. Then the upper screen, 4 screws and a bunch of plugs and she is out. From there, remove the mounting brackets (2 screws each), 4 screws on the rear, 2 screws top and bottom and 3 screws holding in the small plates on each side. When you remove the back cover (tight fit), watch out for the power cable for the fan, I removed it so I could put the back aside. The mainboard is held in by 1 screw in the middle, 1 aerial at the top and 3 ribbon cables. If you've ever done any laptop stuff the ribbon cables are OK to work with, just pop up the retainer and they slide out. If you are not familiar just grab a 12 year old from an iphone factory, they will know how it works The case should now look like this:
    • Switching the console was tricky. First there were 6 screws to remove, and also the little adapter loom and its screws had to come out. Also don't forget to remove the 2 screws holding the central locking receiver. Then there are 4 clips on either side....these were very tight in this case and needed careful persuading with a long flat screw driver....some force required but not enough to break them...this was probably the fiddliest part of the whole job. In my case I needed both the wiring loom and the central locking receiver module to swap across to the new one. That was it for the console, so "assembly is the reverse of disassembly"
    • But first....while I was there, I also swapped across the centre console box for the other style where the AV inputs don't intrude into the (very limited !) space.  Part# was 96926-4GA0A, 284H3-4GA0B, 284H3-4GA0A. (I've already swapped the top 12v socket for a USB bulkhead in this pic, it fit the hole without modification:) Comparison of the 2: Basically to do the console you need to remove the DS and PS side console trim (they slide up and back, held in by clips only) Then remove the back half of the console top trim with the cupholders, pops up, all clips again but be careful at the front as it is pretty flimsy. Then slide the shifter boot down, remove the spring clip, loose it forever somewhere in the car the pull the shift knob off. Remove the tiny plastic piece on DS near "P" and use something thin and long (most screwdrivers won't fit) to push down the interlock and put the shifter down in D for space. There is one screw at the front, then the shifter surround and ashtray lift up. There are 3 or 4 plugs underneath and it is off. Next is the rear cover of the centre console; you need to open the console lid, pop off the trim covering the lid hinge and undo the 2rd screw from the driver's side (the rest all need to come out later so you can do them all now and remove the lid) Then the rear cover unclips (6 clips), start at the top with a trim tool pulling backwards. Once it is off there are 2 screws facing rearwards to remove (need a short phillips for these) and you are done with the rear of the console. There are 4 plugs at the A/V box to unclip Then there are 2 screws at the front of the console, and 2 clips (pull up and back) and the console will come out.
×
×
  • Create New...