Jump to content
SAU Community

Recommended Posts

  • Replies 1.1k
  • Created
  • Last Reply

Top Posters In This Topic

I am down for a Perth ride - I have even given up smoking after 19 years, so kinda interested to see what sort of effect it will have on my fitness...

Congrats man!

Unfortunately it has no effect on your fitness. You will still be farked after excercise. Breathing is easier though.

your heart rate slowing down would be due to your body getting a nicotine fix, plus the fact you arent moving when smoking (assuming that as you might still be riding when smoking??)

the nicotine would remove the anxiety effects symptomised with nicotine withdrawals therefore relaxing your nervous system and assisting with lowering heart rate, blod rpessure.

Of course 30 - 40 minutes later, if you are an excessive smoker, your blood pressure and heart rate would more than likely by higher than a typical person resting heart rate and blood pressure.

5 main symptoms of high bllod pressure that i see is:

Diet

Smoking

Drinking

Genetics

Lack of excerise

Hope that all makes sense....

Worst time to be smoking is directly after excercise, your body is absorbing everything thrown at it! hence why protein intake is recommended 15 - 20 minutes after excerise, protein isolates mainly. In having a cigerette your body would be absorbing the chemicals extremely quickly.

so i have spent the last 45 mins pulling a magnetic trainer apart to see how it works. don't worry kenny it wasn't yours, lol. i had 1 dropped in to be fixed (it's a rim drive one and needs a new belt), so i thought that while i was at it i would find out exactly how they work. fkn interesting stuff. took my a while to figure out. on 1 side there is a solid ring that is a magnet. on the other side 6 smaller magnets. if you touch a piece of metal to anywhere on either of the magnets it will attract the metal, however if you get another magnet, as you go along you will feel the magnet get pulled then pushed away, even on the magnet that is 1 piece and round.

so basically how it works is there is an aluminium plate that spins between the 2 magnets. now aluminium isn't magnetic, but when the resistance is on low the magnets are attracting towards each other and the plate spins easily. as you turn the resistance up the magnets start to oppose each other and obviously this magnetic field causes a resistance that makes it harder for the plate to spin. i don't know enough about magnets to explain it properly, but that is how i think it works, and as far as the 2 magnets attracting and opposing each other, that is know for a fact, because if i open the unit with the resistance at hard it pops open when i undo the screws, but when the resistance is easy i have to pull a bit to get it open.

ok, just did a quick bit of research. i was right about the magnetic for slowing it down. it's called an eddy current. it's also used on rollercoasters and trains. it's a frictionless brake

whats a good tyre pressure to run on my bmx? i just bought a 2009 haro forum from a local dealer, got it cheap cos the 2010 stuffs in. when riding it it feels like the dealer didnt have enough air in the tyres so it doesnt freewheel that well and when i hand squeeze the tyres i'm pretty sure they feel a bit soft to me. same thing happened with the bmx i had last year but i cant remember what i pumped them up to.. so can someone tell me what sort of pressure bmx tyres should be?

read the side of the tyre and see what it says. it could be anywhere up to 100psi, but it depends on the quality of the tyre. better tyres will take higher pressures. generally a lower quality tyre will take up to about 65psi. and yeah 2009 stuff is cheap now because the 2011 stuff will be out in a few weeks. also if it isn't rolling that well then there are 2 other things to check. 1: chain tension. often from the factory the chain will be done up a touch too tight and this can be enough to put a touch more pressure on the bearings and slow things down a bit. 2: the cones in the wheel are a touch tight. again a common factory thing. to check this remove the wheel and spin the axle with your fingers. it should spin easily but not have any play in it.

and dan, i already know how that works.

i found some pics on the apollo facebook page of the 2011 range (only a few pics) and cherie has fallen in love with this bike, so looks like i will be ordering one at the show tomoro. don't know a price yet, but looks to be an entry level ladies road bike, so probably be around the $1000 mark

34855_133201680048634_133196210049181_134799_402180_n.jpg

so today i got a flattie and had to walk the bike about 1km home. lucky it happened on my way back. when i investigated the puncture tonight i found a dirty great big nail sticking through the tyre - yep, that'll do it.

i know how to patch the tube so thats no worries but is it ok to use the same tyre? the hole left by the nail is real tiny but i duno if a tube at 80-100psi might be inclined to try escape through it lol.. thoughts??

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • As discussed in the previous post, the bushes in the 110 needed replacing. I took this opportunity to replace the castor bushes, the front lower control arm, lower the car and get the alignment dialled in with new tyres. I took it down to Alignment Motorsports on the GC to get this work done and also get more out of the Shockworks as I felt like I wasn't getting the full use out of them.  To cut a very long story short, it ended up being the case the passenger side castor arm wouldn't accept the brand new bush as the sleeve had worn badly enough to the point you could push the new bush in by hand and completely through. Trying a pair of TRD bushes didn't fix the issue either (I had originally gone with Hardrace bushes). We needed to urgently source another castor arm, and thankfully this was sourced and the guys at the shop worked on my car until 7pm on a Saturday to get everything done. The car rides a lot nicer now with the suspension dialled in properly. Lowered the car a little as well to suit the lower profile front tyres, and just bring the car down generally. Eternally thankful for the guys down at the shop to get the car sorted, we both pulled big favours from our contacts to get it done on the Saturday.  Also plugged in the new Stedi foglights into the S15, and even from a quick test in the garage I'm keen to see how they look out on the road. I had some concerns about the length of the LED body and whether it'd fit in the foglight housing but it's fine.  I've got a small window coming up next month where I'll likely get a little paint work done on the 110 to remove the rear wing, add a boot wing and roof wing, get the side skirt fixed up and colour match the little panel on the tail lights so that I can install some badges that I've kept in storage. I'm also tempted to put in a new pair of headlights on the 110.  Until then, here's some more pictures from Easter this year. 
    • I would put a fuel pressure gauge between the filter and the fuel rail, see if it's maintaining good fuel pressure at idle going up to the point when it stalls. Do you see any strange behavior in commanded fuel leading up to the point when it stalls? You might have to start going through the service manual and doing a long list of sensor tests if it's not the fuel system for whatever reason.
    • Hi,  Just joined the forum so I could share my "fix" of this problem. Might be of use to someone. Had the same hunting at idle issue on my V36 with VQ35HR engine after swapping the engine because the original one got overheated.  While changing the engine I made the mistake of cleaning the throttle bodies and tried all the tricks i could find to do a throttle relearn with no luck. Gave in and took it to a shop and they couldn't sort it. Then took it to my local Nissan dealership and they couldn't get it to idle properly. They said I'd need to replace the throttle bodies and the ecu probably costing more than the car is worth. So I had the idea of replacing the carbon I cleaned out with a thin layer of super glue and it's back to normal idle now. Bit rough but saved the car from the wreckers 🤣
    • After my last update, I went ahead with cleaning and restoring the entire fuel system. This included removing the tank and cleaning it with the Beyond Balistics solution, power washing it multiple times, drying it thoroughly, rinsing with IPA, drying again with heat gun and compressed air. Also, cleaning out the lines, fuel rail, and replacing the fuel pump with an OEM-style one. During the cleaning process, I replaced several hoses - including the breather hose on the fuel tank, which turned out to be the cause of the earlier fuel leak. This is what the old fuel filter looked like: Fuel tank before cleaning: Dirty Fuel Tank.mp4   Fuel tank after cleaning (some staining remains): Clean Fuel Tank.mp4 Both the OEM 270cc and new DeatschWerks 550cc injectors were cleaned professionally by a shop. Before reassembling everything, I tested the fuel flow by running the pump output into a container at the fuel filter location - flow looked good. I then fitted the new fuel filter and reassembled the rest of the system. Fuel Flow Test.mp4 Test 1 - 550cc injectors Ran the new fuel pump with its supplied diagonal strainer (different from OEM’s flat strainer) and my 550cc injectors using the same resized-injector map I had successfully used before. At first, it idled roughly and stalled when I applied throttle. Checked the spark plugs and found that they were fouled with carbon (likely from the earlier overly rich running when the injectors were clogged). After cleaning the plugs, the car started fine. However, it would only idle for 30–60 seconds before stalling, and while driving it would feel like a “fuel cut” after a few seconds - though it wouldn’t fully stall. Test 2 – Strainer swap Suspecting the diagonal strainer might not be reaching the tank bottom, I swapped it for the original flat strainer and filled the tank with ~45L of fuel. The issue persisted exactly the same. Test 3 – OEM injectors To eliminate tuning variables, I reinstalled the OEM 270cc injectors and reverted to the original map. Cleaned the spark plugs again just in-case. The stalling and “fuel cut” still remained.   At this stage, I suspect an intermittent power or connection fault at the fuel pump hanger, caused during the cleaning process. This has led me to look into getting Frenchy’s fuel hanger and replacing the unit entirely. TL;DR: Cleaned and restored the fuel system (tank, lines, rail, pump). Tested 550cc injectors with the same resized-injector map as before, but the car stalls at idle and experiences what feels like “fuel cut” after a few seconds of driving. Swapped back to OEM injectors with original map to rule out tuning, but the issue persists. Now suspecting an intermittent power or connection fault at the fuel pump hanger, possibly cause by the cleaning process.  
×
×
  • Create New...