Jump to content
SAU Community

Recommended Posts

380RS fender flares installed

c605bcc8-46d8-4259-994d-a5f479ad681a_zps

Nissan-NISMO-Fairlady-Z-Type-380RS-350hp

Looking good Am, like its crouching. Any trouble fitting/blended them in?

Always loved JDM James' G35 (if I'm honest, the hood was not to my taste), now that thing had some flares on it...

They fit pretty nice. The front bumper side marker light gets in the way. Other than that, not bad at all.
JDMJames had a nice ride. Someone else owns it now. I always have to try something different. I wasn't willing to cut up my stock fenders (especially the rear) for $200 riveted on fender flares that can't be undone.

6eaecd04-5f44-4e5a-97f3-b8f363bee0b6_zpsfee4d943-27f3-4adc-9a67-2b09937b8249_zps16c0ca31-f214-4f19-b6fe-ce5d9958b634_zps

Edited by SleepyRN

Chris your car is beyond awesome.

Question-

Why haven't you upgraded to projector headlights?

Dont thinknit will fit in with the style hes going for. 380RS fender flares....thats an awesome idea!

Thanks! I do really enjoy how the reflector lights blend in with the paint. The projectors just seem to be so "bright" with their chrome finish.

I am running a cup kit that is custom fitted to my coilovers.

Thanks again :) Always enjoy seeing VQ's from across the world and sharing mine with you guys!

For anyone that hasn't seen my thread on the V35 front page (I know I almost never check it) - anyone after a Urethane Nismo copy front bumper? I remember a while back when I discussed bringing some in a few people wanted them.

http://www.skylinesaustralia.com/forums/topic/432230-f-s-v35-coupe-urethane-nismo-style-front-bumper-bars/

  • 2 months later...
  • 2 weeks later...

Hey mate nice 300 but if you plan to go lower than that i would remover the mudspats behind the front wheels as they will hit on bumpa and coming out of driveways and what not and breaking other parts. What are the wheel and tire specs?

1469854_10202660558696616_2064180614_n.j

Almost there ... !!! :X :X :X

Woah!! Dat ride height!!!!! Persobally i would have put coilovers in first before wheels and all that cosmetic stuff that does nothing for performance. Enjoy running spacers on those wheels when coilovers go in!

  • 2 weeks later...

Lol yeah, it's chillin out up there so it doesn't get stepped on!

Got the other side halfway done. It's at a different angle than the drivers side. Just still trying to get a feel for how I want to place them. Still have a lot of cutting to do on them.

20140102_111253_zpsv4jdqzis.jpg

New wheels are behind schedule... still about 3 weeks away from being done :verymad: Were supposed to be done by now!

The Gram Lights are being passed around. No owner has kept them longer than a month. They're getting beat up, I'm sure... sad story...

Going with a real classic wheel next, but haven't seen any V35's or Z33's when them yet! So it'll be interesting! I'll post up pics as soon as they are done getting made!

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Hi, is the HKS  Tower Bar still available ? negotiable ? 🤔
    • From there, it is really just test and assemble. Plug the adapter cables from the unit into the back of the screen, then the other side to the car harness. Don't forget all the other plugs too! Run the cables behind the unit and screw it back into place (4 screws) and you should now have 3 cables to run from the top screen to the android unit. I ran them along the DS of the other AV units in the gap between their backets and the console, and used some corrugated tubing on the sharp edges of the bracket so the wires were safe. Plug the centre console and lower screen in temporarily and turn the car to ACC, the AV should fire up as normal. Hold the back button for 3 sec and Android should appear on the top screen. You need to set the input to Aux for audio (more on that later). I put the unit under the AC duct in the centre console, with the wifi antenna on top of the AC duct near the shifter, the bluetooth antenna on the AC duct under the centre console The GPS unit on top of the DS to AC duct; they all seem to work OK there are are out of the way. Neat cable routing is a pain. For the drive recorder I mounted it near the rear view mirror and run the cable in the headlining, across the a pillar and then down the inside of the a pillar seal to the DS lower dash. From there it goes across and to one USB input for the unit. The second USB input is attached to the ECUtec OBD dongle and the 3rd goes to the USB bulkhead connected I added in the centre console. This is how the centre console looks "tidied" up Note I didn't install the provided speaker, didn't use the 2.5mm IPod in line or the piggyback loom for the Ipod or change any DIP switches; they seem to only be required if you need to use the Ipod input rather than the AUX input. That's it, install done, I'll follow up with a separate post on how the unit works, but in summary it retains all factory functions and inputs (so I still use my phone to the car for calls), reverse still works like factory etc.
    • Place the new daughterboard in the case and mount it using the 3 small black rivets provided, and reconnect the 3 factory ribbon cables to the new board Then, use the 3 piggyback cables from the daughterboard into the factory board on top (there are stand offs in the case to keep them apart. and remember to reconnect the antenna and rear cover fan wires. 1 screw to hold the motherboard in place. Before closing the case, make a hole in the sticker covering a hole in the case and run the cable for the android unit into the plug there. The video forgot this step, so did I, so will you probably. Then redo the 4 screws on back, 2 each top and bottom, 3 each side and put the 2 brackets back on.....all ready to go and not that tricky really.      
    • Onto the android unit. You need to remove the top screen because there is a daughterboard to put inside the case. Each side vent pops out from clips; start at the bottom and carefully remove upwards (use a trim remover tool to avoid breaking anything). Then the lower screen and controls come out, 4 screws, a couple of clips (including 3 flimsy ones at the top) and 3 plugs on the rear. Then the upper screen, 4 screws and a bunch of plugs and she is out. From there, remove the mounting brackets (2 screws each), 4 screws on the rear, 2 screws top and bottom and 3 screws holding in the small plates on each side. When you remove the back cover (tight fit), watch out for the power cable for the fan, I removed it so I could put the back aside. The mainboard is held in by 1 screw in the middle, 1 aerial at the top and 3 ribbon cables. If you've ever done any laptop stuff the ribbon cables are OK to work with, just pop up the retainer and they slide out. If you are not familiar just grab a 12 year old from an iphone factory, they will know how it works The case should now look like this:
    • Switching the console was tricky. First there were 6 screws to remove, and also the little adapter loom and its screws had to come out. Also don't forget to remove the 2 screws holding the central locking receiver. Then there are 4 clips on either side....these were very tight in this case and needed careful persuading with a long flat screw driver....some force required but not enough to break them...this was probably the fiddliest part of the whole job. In my case I needed both the wiring loom and the central locking receiver module to swap across to the new one. That was it for the console, so "assembly is the reverse of disassembly"
×
×
  • Create New...